最小接種密度 的英文怎麼說

中文拼音 [zuìxiǎojiēzhǒngmìdù]
最小接種密度 英文
minimal inoculum density
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 小 : Ⅰ形容詞1 （體積、面積、數量、強度等不大） small; little; petty; minor 2 （年紀小的; 年幼的） youn...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 種 : 種名詞（姓氏） a surname
  • 密 : Ⅰ名詞1 （秘密） secret 2 [紡織] （密度） density 3 （姓氏） a surname Ⅱ形容詞1 （距離近; 空隙小）...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 接種 : [醫學] vaccinate; have an inoculation; inoculate
  1. Primary culture of rat preadipocyte were prepared from the epididymal, inguinal and perirenal the fat pads of male normal, healthy, 15 - 20 days sprague - dawley rats. the preadipocyte grew better under the condition of 37, 95 % humidity, 5 % co2, ph 7. 0 - 7. 2, centrifuged at 1000r / min, m199medium, and 10 % fetal bo vine serum, seeded at a density of 4 l04, 5 l04, / cm2. oil red o staining was the special method to distinguish adipocyte from other cells, gimsa and he could determine the stage of the adiopcyte differentiation through the number of lipid drop, size and the position of the nucleolus of the staining fat cell

    經過多次實驗，確定本實驗室大鼠前體脂肪細胞的最佳培養條件是：溫度為37 ，濕度為95 ， co _ 2濃度為5 ， ph值為7 . 0 7 . 2 ，離心力為1000r / min ，培養基為m _ （ 199 ）培養基，胎牛血清濃度為10 ，合適細胞接種密度為4 10 ~ 4 、 5 10 ~ 4個/ cm ~ 2 ，染色結果表明：油紅o染色是鑒定脂肪細胞的特異方法， gimsa和he染色可根據不同區域染色程度、著色差別判斷細胞核的位置及脂滴大小、多少，觀察大鼠前體脂肪細胞分化過程中的形態變化，進而確定脂肪細胞的分化階段。
  2. ( 3 ) there are many flaws in direct laser metal sintering, such as the high remnants stress, micro - hole and micro - crack in sintering parts. in order to solving those problems, the programming of scanning paths is put forward, and several parts are prepared with different scanning paths respectively. the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure, the rigidity of parts prepared by short - side and same direction scanning path is highest, and the density of parts produced with the vertical scanning path is maximal

    （ 3 ）針對採用大功率激光直接燒結鎳基高溫合金成形金屬零件存在的問題，如較大的殘余應力，製件中存在著微裂紋、微孔洞等缺陷，初步提出掃描路徑的規劃，並採用幾種不同的掃描方式進行燒結試驗，發現採用短邊掃描路徑和同向掃描能夠獲得更加細小和分佈均勻的組織結構，採用短邊同向路徑制備的試樣其顯微硬度最高，而採用變向掃描（垂直）路徑制備的試樣緻密性最好。
  3. The results show that : in the 2 - 4m of road buffer zones and 0 - 10m of infrastrctuer buffer zones, the density of dominant species and biomass will decrease for herbs, and abundance and proportion will get bigger than other exents ( inner species increasing owing to the outer species invading ) ; in the shrub disturbence extent, there exists an inverse relationship between the influence degrees and buffer zones ; in the 40m of infrastructure buffer zones, there has the biggest influence on the trees, however, the effect of road buffer zones is unobvious, only a small change on the morphology

    結果表明，草本類，游道影響源干擾區在2 4m ，設施類在0 10m ，原有優勢種密度減小，物種豐度較其它干擾范圍內有所增加（外部種入侵導致本地植物的種類數目增多） ，均勻度也增大，生物量減少；灌木類，在干擾范圍內，影響程度與影響源的距離成負相關關系；喬木類，接近設施類40m處影響最大，游道類影響源則影響效果不明顯，只有形態上略有變化。
  4. The fem results indicated that as to the rough surfaces in sliding contact, the value of the contact pressure was very high which coursed a high value of the heat flow rate, meanwhile the sliding time was not enough for the frictional heat to transfer, thus the highest value of the body temperature occurred just on the sliding surfaces, which possessed a sharp thermal gradient in direction perpendicular to the sliding surface. so the great thermal stress was caused just by the sharp gradient and the thermal elastic distortion with which the contact pressure changed occurred simultaneously, thus this change of the contact pressure would affect the temperature distribution in return

    對于相對滑動的粗糙表面，因實際接觸面積小而導致接觸壓力很大，這樣使得熱流密度會很大，同時由於滑動時間很短，熱來不及傳導，最高溫度發生在摩擦表面，在垂直於摩擦面的方向有很大的溫度梯度，使得熱應力很大，且最大應力發生在表面，同時產生熱彈性變形，這種變形使得接觸區域內的壓力分佈發生變化，這種變化又反過來影響了接觸區域的溫度分佈。
分享友人
分享到 Line

分享到臉書