最小槽寬 的英文怎麼說

中文拼音 [zuìxiǎocáokuān]
最小槽寬 英文
minimum slot width
  • : 副詞(表示某種屬性超過所有同類的人或事物) most; best; worst; first; very; least; above all; -est
  • : Ⅰ形容詞1 (體積、面積、數量、強度等不大) small; little; petty; minor 2 (年紀小的; 年幼的) youn...
  • : 名詞1 (盛牲口飼料或飲料等液體的器具) trough; manger (for water animal feed wine vat) 2 (兩邊...
  1. In order to reduce the re - deposit volume of the dredged channel, the method must be based on decreasing the oncoming sediment, changing the mouth site, builting the sediment control dam and raising the reservoir level

    為了大限度地減疏浚挖的回淤量,必須依靠控制上游來沙量、調整入水口門位置、加設防淤堤及提高庫水位等手段,而不能通過調整挖泥度、位置及數量等措施來達到目的。
  2. Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

    將液體火箭發動機燃燒室的冷卻通道設計為斜航線(等傾角螺旋線)形,可以大幅度改善燃燒室的冷卻性能.斜航線冷卻尺寸較深尺寸較大,所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點,提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜,手工編制數控加工程序難度大.為了解決數控加工程序的編制問題,研究了斜航線的數學模型,開發了自動編程軟體系統.使用該系統,可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大,加工難度大,是斜航線冷卻通道加工的典型工件.經過理論分析和實際切削實驗,研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術,已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用,驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功,對其他相似類型零件的加工亦具有參考意義
  3. To avoid the serious electromagnetic interferer, the analog signals are transformed to frequency pulses which are transferred to the kernel of the system. in the measure of the groove voltage, the method of float - ground is adopted to avoid the high common signal and the range switch circuit is designed to solve the conflict of the wide dynamic range and the high precision. least square curvefit is adopted to reduce the system error

    鋁電解生產現場電磁干擾非常嚴重,為此我們將需要測量的模擬信號就近轉換為頻率脈沖后再傳送到控制核心;採用浮地接入方式消除電壓信號中的共模成分;設計了量程自動切換電路以解決電壓的動態范圍和測量精度高的矛盾;用二乘法進行曲線擬和以降低測量的系統誤差。
  4. Minimum slot width

    最小槽寬
  5. The distribution of streak width along the lateral direction shows that the width attains its maximum value at the central line and becomes narrower toward the side wall, and its distribution is symmetrical about the central line of the flume

    低速帶度在水中心位置大,往兩邊的邊壁逐漸減,而且在橫向上相對於水中心線對稱分佈。低速帶間距與度的比值約為2 0 。
分享友人