最小轉換鍵控 的英文怎麼說
中文拼音 [zuìxiǎozhuǎnhuànjiànkòng]
最小轉換鍵控
英文
minimum shift keying- 最 : 副詞(表示某種屬性超過所有同類的人或事物) most; best; worst; first; very; least; above all; -est
- 小 : Ⅰ形容詞1 (體積、面積、數量、強度等不大) small; little; petty; minor 2 (年紀小的; 年幼的) youn...
- 轉 : 轉構詞成分。
- 換 : 動詞1. (給人東西同時從他那裡取得別的東西) exchange; barter; trade 2. (變換; 更換) change 3. (兌換) exchange; cash
- 鍵 : 名詞1 [機械工程] (使軸與齒輪、皮帶輪等連接並固定在一起的零件) key 2 [書面語] (插門的金屬棍子)...
- 控 : 動詞1 (告發;控告) accuse; charge 2 (控制) control; dominate 3 (使容器口兒朝下 讓裏面的液體慢...
- 轉換 : change; transform; convert; switch
-
To accept the current signal from high negative voltage circuit, the analog ground is raised to a certain positive voltage, which makes it possible for the signal amplitude to be compressed at the same time of its polarity reversion. a pi control program special for laser gyro current control is brought forward according to the conventional pid control method, in which the control signal is figured out corresponding to the difference between the sample and the reference value by turn of proportion - short step integral - long step integral. and at the end of this paper, a comparison of system performance on different conditions is made and the key elements influencing system performance are educed
利用集成a / d 、 d / a轉換器的新型晶元aduc824 ,實現了電流(電壓)采樣?數據處理?電流控制的閉環控制結構;地電位的抬升解決了a / d轉換器對負高壓迴路電流采樣時的輸入范圍匹配問題;控制信號反相的同時進行幅度壓縮,使得輸出調整電壓的解析度提高;根據常規的比例?積分?微分( pid )調節模型,針對陀螺系統的特性,給出了一種可以滿足系統要求、據采樣值偏差大小進行的比例?大步長積分?小步長積分、分層次比例?積分演算法;不同條件下系統穩流性能的對比、分析在論文最後給出,並據此找出了決定該系統穩流精度的關鍵因素,提出了系統的改進意見。Pressing y again will toggle thumbwheel control from moving the min / max cursor to scrolling an entire screen
若再次按y鍵將使滾輪的控制從移動最小/最大指針切換為轉動整個屏幕。Aim to the special model nc bend tube, use the modeling method that essential parameter drive product sample model ; 3 ) in the foundation that summing up a rule of optimized welding assembly underside of tube, develop the nc bend tube welding underside optimization design tool, then complete the optimization design united with two application methods : rotation method and the least squares method ; 4 ) propose a design method of nc bend tube welding jig bottom base, then establish model storehouse according to the design rules, and endow the foundation model with assembly feature
針對多數通用型數控導管,運用矢量轉換演算法反求得導管關鍵特徵,並據此創建導管模型,針對特殊造型數控導管,使用關鍵參數驅動產品庫樣本模型的方法完成建模; 3 )在歸納總結了焊接底面創建規則的基礎上,開發數控導管焊接底面優化設計工具,分別應用旋轉法和最小二乘法兩類方法完成底面的優化設計; 4 )提出了一種數控導管焊接底座設計方法。
分享友人