最後切削 的英文怎麼說
中文拼音 [zuìhòuqiēxiāo]
最後切削
英文
finish cut-
The effect of cutting speed, cutting thickness, cutting knife and materials on the working power capacity is discussed. finally tractive property of road plane milling machine is also studied. through the comparison of the results of theory calculation and experimental results the equation of working power capacity of milling machine is modified
本文對冷式瀝青路面銑刨機的動力學工作過程進行了理論分析與試驗研究，並利用金屬材料切削的基本原理，研究了主切削力，並從能量轉化守恆的角度推導了銑刨機銑刨作業阻力和功率計算公式，討論了機器切削速度、銑刨厚度以及刀具與材料特性對銑刨作業阻力和功率的影響規律，最後討論了銑刨機牽引性能，且通過試驗研究驗證了銑刨作業阻力和功率公式。Finally, he is anxious to see if you have been fortunate enough to escape the bad moral influence to which you have been exposed, and which is infinitely more to be dreaded than any physical suffering ; he wishes to discover if the fine abilities with which nature had endowed you have been weakened by want of culture ; and, in short, whether you consider yourself capable of resuming and retaining in the world the high position to which your rank entitles you.
最後，他迫切想知道您是不是有幸地擺脫過精神上的不良影響，那肯定要比任何肉體上的痛苦更不可忍受，他希望知道您天生的優良本性有沒有因為缺乏教育而被削弱。總之，您自己到底認為您能不能重新在社會上維持與您高貴的身份相稱的地位。 」At last, the conclusion is got that proper ultrasonic vibration can enhance the efficiency of the normal maf due to the ultrasonic vibration can make the grain flow more frequently and then refresh the milling - grain on - working and sharpen the grain ' s blade
最後對實驗結果進行了分析，得出功率大小適當的超聲振動可以促進磨粒刃口自銳，工作磨粒及時更新，從而提高磨刷切削能力等結論。The topography and the nano - mechanical property of the sample before and after self - assembly was characterized by afm, and the factor attributed to the change was analyzed. based on the above conclusion, the nano - mechanical property of the sample fabricated with the technology based on the scratch of afm microprobe combining traditional self - assembly method was analyzed. it was proved that this method could carry out controllable self - assembly on silicon surface ; finally, the nano - mechanical property of the sample fabricated with the technology based on the cutting of diamond tool was measured, and this method was proved to be a quick and convenient mean that could carry out controllable self - assembly on silicon surface according to the nano - mechanical property of the samples fabricated by the two method before
之後利用原子力顯微鏡對組裝前後的樣品進行了表面形貌和納米機械性能的表徵，分析了可能導致其變化的原因;藉助所得的結論，對基於原子力顯微鏡微探針的刻劃與傳統自組裝方法相結合的自組裝加工技術所制備的樣品進行了納米機械性能的分析，證明這種方法能夠實現硅基底上的可控自組裝;最後，對基於金剛石刀具切削的自組裝加工技術所制備樣品的納米機械性能進行了檢測，通過和前兩種方法制備的自組裝結構的納米機械性能進行對照，證明這種方法可以方便快捷的實現硅基底上的可控自組裝，從而實現「割草種花」的構想。Then, predicting the optimum performance and validating the optimum cutting conditions by using a confirmation experiment
預測經最優切削參數加工得到的表面粗糙度值，最後通過確認實驗驗證了其正確性。分享友人