最高燒成溫度 的英文怎麼說

中文拼音 [zuìgāoshāochéngwēndù]
最高燒成溫度 英文
peak firing temperature
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 燒成 : baking
  • 溫度 : [物理學] temperature
  1. The influence of burning system on the properties and structure of the ceramic capacitors has been studied under the certain temperature system, the optimum sintering temperature of the ceramics was primarily decided by the content of bi2o3 ? 3tio2. the sintering temperature dropped with the adding of bi2o3 ? 3tio2. at the range of suitable sintering temperature, slow heating and low temperature sintering can obtain fine grain and dense structure. it results in the improving of the breakdown voltage for the middle - high voltage ceramic capacitors

    研究了燒成工藝制度對電容器陶瓷性能和結構的影響，結果表明：在一定的升溫保溫時間下，瓷料的最佳燒結溫度主要取決于組成中bi _ 2o _ 3 ? 3tio _ 2的含量， bi _ 2o _ 3 ? 3tio _ 2含量的增加將降低燒結溫度；在合理的燒結溫度范圍內，慢速升溫和低溫燒結將有利於得到細晶緻密結構，從而改善中高壓陶瓷電容器的耐壓強度。
  2. The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites

    研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。
  3. A new calculation method for optimizing diesel engine performance, called nonlinear regression - mess method, is put forward. in this paper, 25 groups of simulated values are calculated from the diesel engine working model, specific fuel consumption, peak pressure, rate of pressure rise, nox and peak temperature are fitted into explicit function about compression ratio and fuel injection advance angle

    本文利用柴油機工作過程模型，得出25組模擬計算數據，利用非線性回歸將油耗、最大爆發壓力、壓力升高率、 no _ x濃度及最高燃燒溫度擬合成壓縮比和噴油提前角的顯函數，並用網格法進行優化，用c語言編制了優化計算程序，得出最佳的壓縮比和噴油提前角，使其優化匹配。
  4. Bell - style hydrogen furnace : the bell - style hydrogen furnace can be operated at temperature as high as 2050oc under reducing or inert atmosphere such as hydrogen, nitrogen and argon

    從美國進口的高溫真空氣氛燒結爐，最高燒結溫度2050 ，能在氫氣、氮氣以及氬氣等氣氛下完成工藝操作。
  5. Results of the experiments showed that the wear mechanisms of the sintered steel included abrasive wear, adhesive wear and fatigue wear, and it was the abrasive wear most important. it was the sintered steel mixed by ni, mo that was the best on the wear resistance, because of the great lot of bainite ; the sintered steel quenched and low temperature tempered mixed by mo, w that was the best on the wear resistance, because of the rigidity of the steel was the highest

    實驗結果表明：本文中幾種燒結鋼的磨損機制均是由磨粒磨損、粘著磨損、和疲勞磨損共同作用的，且以磨粒磨損為主；在燒結態下，復合添加合金元素鎳、鉬的燒結鋼的耐磨性能最好，這是因為生成了大量的硬質相貝氏體；而淬火、低溫回火態下，則復合添加鉬、鎢的燒結鋼的耐磨性能最好，這是因為熱處理態下添加鉬、鎢的燒結鋼的硬度最高。
  6. The influence of preparing conditions on aluminum titanate composing was inquired. by analyzing element content of alumina and titania source, arranging a stoichiometric dosage, and keeping the chemical homogeneity from sol to mixed ti - al oxide precursor, a high activity powder was prepared. after calcining the precursor powder at 1250 for 2h, aluminum titanate phase is formed

    本試驗通過準確測定起始物的ti 、 al含量，嚴格化學配比，採取適當措施將微尺度上的組成均勻性從溶膠一直保持到混合鋁鈦氧化物前驅體的生成，使該粉體具有高活性，將其在1250煅燒2h ，已合成出以鈦酸鋁為主晶相的產物，比文獻報道的鈦酸鋁相的最低生成溫度降低了50 。
  7. ( 3 ) there are many flaws in direct laser metal sintering, such as the high remnants stress, micro - hole and micro - crack in sintering parts. in order to solving those problems, the programming of scanning paths is put forward, and several parts are prepared with different scanning paths respectively. the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure, the rigidity of parts prepared by short - side and same direction scanning path is highest, and the density of parts produced with the vertical scanning path is maximal

    （ 3 ）針對採用大功率激光直接燒結鎳基高溫合金成形金屬零件存在的問題，如較大的殘余應力，製件中存在著微裂紋、微孔洞等缺陷，初步提出掃描路徑的規劃，並採用幾種不同的掃描方式進行燒結試驗，發現採用短邊掃描路徑和同向掃描能夠獲得更加細小和分佈均勻的組織結構，採用短邊同向路徑制備的試樣其顯微硬度最高，而採用變向掃描（垂直）路徑制備的試樣緻密性最好。
  8. By the increasing of temperature, liyco3 - xo4 was further changed into licoo2 and lixco1 - xo, and then licoo2 formed by the reaction of lixco1 - xo with li2o. the reaction that produces licoo2 is almost completely done at 700, although some remaining li2o and li2co3 present as a partially amorphous film dispersed on the surface of licoo2, which can accelerate the growth of licoo2 crystallites. however, when temperature is higher than 850, some of licoo2 begin to decompose into the solid solution phase of liyco2 - yo2 and lixco1 - xo, and damaged its own crystal structure

    制備licoo _ 2的合成反應中licoo _ 2的微結構不斷發生變化，隨著焙燒溫度升高， co _ 3o _ 4晶粒逐漸減小， licoo _ 2晶粒和顆粒逐漸長大，晶格內部缺陷減少， licoo _ 2晶格趨于完整，在焙燒溫度為850時licoo _ 2晶粒達到最大值；焙燒溫度低於700 ，晶胞參數a隨著焙燒溫度上升而減小，晶胞參數c隨著焙燒溫度上升而增大；而高於700則晶胞參數基本保持不變。
  9. The sample composition was analyzed by means of tg and x - ray diffraction. the following conclusions can be drawn from the experiments : given conditions, the sample powder that has the same xrd data as the standard fetioa can be gotten when use any method mentioned above ; the key in synthesis is to avoid the oxidation of fe2 +, so the whole process should performed under vacuum or neutral atmosphere, samples used by this study were prepared under nitrogen atmosphere ; the heat - treated time and temperature have some influence on the sample powder, results show that the proper time and temperature is 120 minutes and 1100 respectively

    研究結果表明：在合適的反應條件下，用上述三種合成方法都能得到xrd數據與標準fetio _ 3物相基本吻合的粉體；合成反應需要克服的主要問題是防止體系中fe ~ （ 2 + ）的氧化，因此，整個反應必須在真空或者非氧化性氣體保護下進行，本研究需要的樣品是在高純從保護下合成的；煅燒的時間和溫度對最終的產物也有一定的影響，研究發現：合理的煅燒時間和溫度分別為120分鐘和1100 。
  10. In the process of making 95 alumina ceramics, selected five kinds of alumina powder and studied the influence of different alumina powder on the sintering properties and mechanic properties of 95 alumina ceramics, moreover, selected the most agreeable alumina powder according to the apparatus for granularity analysis and scanning electron microscope ( sem ). the influence of different sintering temperature on the sintering mechanic properties, the microstructure of 95 alumina ceramics were investigated by adding y2o3 and la2o3 as two kinds of rare earth additives in alumina ceramics. the results indicated that the additive of la2o3 could improve the properties of 95 alumina ceramics more effectively and could get fine grain and tabular alumina that can enhance the strength of the material

    選用了五種al2o3粉料，研究了其對95al2o3瓷燒結性能和力學性能的影響，並結合粒度分析儀sem對al2o3粉料進行優選；通過添加y2o3 、 la2o3兩種稀土添加劑，研究了不同燒成溫度對95al2o3瓷的燒結性能、力學性能及顯微結構等的影響，結果表明：添加la2o3可以有效提高95氧化鋁瓷燒結性能和力學性能，形成細晶和板狀氧化鋁瓷的顯微結構；通過對比不同氧化鋁粉料制備氧化鋁瓷燒成溫度曲線與燒結性能的關系，確定最佳的燒成溫度范圍為1570 ~ 1600 。
  11. Changing the grading of sic particles not only affects the strength and pile density, but also modifies the phase compositions and microstructure of the material. with the reducing of sic particles, the strength of the material increases obviously. the nitrification scheme has the greatest influence on phase compositions and microstructure " of si3n4 ( si2on2 ) - sic, after two continuous nitrification reacting peak and short - time high - temperature treating, the best properties can be obtained ; and the residual strength of the composite is much higher after the thermal shock resistance test, which shows that the material possesses excellent thermal shock resistance

    本論文較全面地探討促進強度和顯微結構良好的si _ 3n _ 4 （ si _ 2on _ 2 ）結合相的實驗條件，實驗數據顯示：引入適量的燒結助劑能夠促進si _ 3n _ 4 （ si _ 2on _ 2 ）的生成和晶粒的長大，而過量時，其促進作用反而下降；隨著si粉加入量增加，生成的結合相明顯增多，復合材料的性能顯著提高；改變sic顆粒級配不僅影響復合材料的強度與堆積密度，而且對復合材料的物相與顯微結構也有影響，隨著顆粒逐漸細化，材料的強度有較大的提高；對復合材料的強度、物相與顯微結構影響最大的是氮化制度，經過兩個氮化高峰連續的反應和短時間的高溫后處理得到的復合材料性能最好；通過抗熱震性能實驗后復合材料的殘余強度較高，顯示出較好的抗熱震性能。
  12. Moreover, the sio2 / tio2 composite thin film showed the lowest pl intensity due to a decrease in the recombination rate of photo - generated electrons and holes under uv light irradiation, which further confirmed the film with the highest photocatalytic activity at 700 c. when the calcination temperature was higher than 700 c, the decrease in photocatalytic activity was due to the formation of rutile and the sintering and growth of tio2 crystallites resulting in the decrease of surface area

    同時，此時sio _ 2 / tio _ 2復合薄膜的熒光光譜顯示最低的熒光強度，這表明此時薄膜中的光生電子和空穴的復合速率最低，因而更有利於物質的光催化降解。當熱處理溫度高於700時，武漢理工大學碩士學位論文薄膜的光催化活性下降，這是由於薄膜中晶相二氧化欽的燒結和成長導致樣品的表面積下降以及金紅石相的形成。
  13. At the same sintering temperature, when the alumina fiber accounted for 10 %, the porosity of the composites was the lowest, the volume density was the biggest, and the compressive strength and the bending strength were the highest. when the sintering temperature was 1550 c, the compressive strength which could reach 332. 78 mpa, was the biggest ; when the sintering temperature was 1550 c, the bending strength which could reach 44. 04 mpa, was the biggest

    在同一燒成溫度下，氧化鋁纖維含量為10時，復合材料的氣孔率最低，體積密度最大，耐壓強度和抗折強度最高；燒成溫度在1550時，復合材料的耐壓強度最高，達到332 . 78mpa ，在1500時，復合材料的抗折強度最高，達到44 . 04mpa 。
  14. Its a high performance, low temperature coefficient permanent magnet with its high working temperature350 degree centigrade. when working above 180 degree centigrade, its maximum energy product bh and steady temperature are superior than ndfeb magnetic materials

    是由釤鈷和其它金屬稀土材料經配比，溶煉成合金，經粉碎壓型燒結后製成的一種磁性材料，具有高磁能積極低的溫度系數，最高工作溫度可達
  15. Polymer - network gel process was used to synthesize nanometer oxide such as zro2 ( 3. 5mol % cao ), co3o4 and nio. dta / tg, xrd and tem were used to characterize the gel and products, and determine the lowest temperature and time for calcining the gel. the effect of the concentration of starting solution, temperature and time for calcining the gel on the size of the products were also discussed

    本文採用高分子網路凝膠法進行納米zro _ 2 （ 3 . 5mol cao ） 、 co _ 3o _ 4 、 nio等納米氧化物超細粉的軟化學合成，利用dta tg 、 xrd和tem等分析手段對凝膠和產物超細粉進行表徵，確定凝膠的最低煅燒溫度和煅燒時間，並探討起始無機鹽溶液濃度、凝膠的煅燒溫度和煅燒時間對產物超細粉粒徑的影響。
分享友人
分享到 Line

分享到臉書