有兩裂片的 的英文怎麼說

中文拼音 [yǒuliǎnglièpiānde]
有兩裂片的 英文
bilobular
  • : 有副詞[書面語] (表示整數之外再加零數): 30 有 5 thirty-five; 10 有 5年 fifteen years
  • : Ⅰ數詞1 (數目) two 2 (表示不定的數目) some; a few Ⅱ量詞(市兩的通稱) liang a unit of weight ...
  • : 裂動詞[方言] (東西的兩部分向兩旁分開) open
  • : 片構詞成分。
  • : 4次方是 The fourth power of 2 is direction
  1. The coqen basin in xizang lies between the bangong - nujiang suture zone and yarlung zangbo suture zone, and once extended northwards and southwards, respectively centred by the qiekan - goicang - asog rift zone as the center of deposition and subsidence during the middle jurassic to the early creatceous. ( 1 ) during the middle - late jurassic, the rift zone was occupied by deep - water turbidites, radiolarian siliceous rocks, shallow - water carbonate rocks, clastic rocks and basic - ultrabasic rocks, while both sides of it by littoral and shallow marine elastic rocks and carbonate rocks

    摘要位於班公湖怒江縫合帶與雅魯藏布江縫合帶之間措勤盆地,在中侏羅世早白堊世期間具以且坎古昌阿索谷帶為沉積、沉降中心向南北側展開古地理格局:中晚侏羅世時期,谷帶內由深水濁積巖、放射蟲硅質巖和淺水碳酸鹽巖、碎屑巖巖及基性超基性巖等組成;谷帶側由濱淺海相碎屑巖和碳酸鹽巖組成。
  2. He had a gray face, with slitted eyes, and a pinched nose saddled by faint blue shadows.

    一張灰白臉,長著一對縫似小眼睛和一個被挾過似鼻子,鼻樑側各淡淡烏青。
  3. For laminate containing penetrated crack, " two planes " model is introduced to analyze the influence of repair parameters on the strength of repaired laminate, including such as patch size, patch thickness, patch layout, the location of rivets

    摘要針對含穿透性損傷層壓板,採用「板」模型建立起機械連接修補結構限元分析模型,分別計算補大小、厚度、鋪排方式以及連接件位置等修補參數對修補效果影響。
  4. Through comparing and analyzing of bearing capacity, development of crack and strain of reinforced, the results show that the load - deflection plots f or specimens from the finite element analysis agree well with the experimental data, and choosing the rightful stress - strain relationship, utilizing ansys program, the test process can be well simulated. at the same time, making used of the program, the traditional shear wall is analyzed. it shows that comparing with the traditional shear wall, the hollow shear wall ' s cracking load drop 16 %, yield load and failure load drop 13 %, stiffness drop 13 % ~ 22 %

    其次在試驗基礎上,將試驗手段、限元數值模擬方法和理論分析結合起來,利用限元程序ansys對其中墻板進行非線性限元分析,並對前後承載性能,縫發展、鋼筋應變進行了比較和分析,結果表明限元節點模型分析荷載-位移曲線和試驗測得數據符合良好,選用合理材料本構模型,利用ansys可以較好模擬試驗過程;同時利用限元模型對比分析了普通剪力墻和空心剪力墻,空心剪力墻與普通剪力墻對比,其開荷載下降16 ,屈服荷載、極限荷載下降13 ,剛度下降13 22 ,開至屈服、屈服至極限荷載階段剛度衰減規律與普通剪力墻基本一致,空心剪力墻後期剛度比較穩定。
  5. The cloven halves were not broken from each other, for the firm base and strong roots kept them unsundered below ; though community of vitality was destroyed - the sap could flow no more : their great boughs on each side were dead, and next winter s tempests would be sure to fell one or both to earth : as yet, however, they might be said to form one tree - a ruin, but an entire ruin

    半並沒完全脫開,因為堅實樹基和強壯樹根使底部仍然連接著。盡管生命整體遭到了破壞一樹汁已不再流動,每一大樹枝都已枯死,明年冬天暴風雨一定會把或者都刮到地上,但是它們可以說合起來是一棵樹一雖已倒地,卻完整無缺。
  6. The automatically inspect and control system for thickness of tire cord fabrics is not equipped for the calendar machines that made in china up to now. because of the thickness of tire cord fabrics is measured and controlled by manual, the quality of products cannot be guar anteed and a lot of rubber compound were wasted. in the article, the data process and data read of the other calendaring process parameters have designed

    另外,由於被控制膠厚度較薄,若控制系統執行機構大幅度動作,嚴重時可能造成壓延機輥相抵,使輥筒斷等重大設備事故,因此,在常規控制基礎上,通過採用增量式調節特點,來實現厚度自動控制,建立並推導切合現場實際使用數學檢測公式和數學控制模型,然後通過編制相應計算機軟體來實現控制, 。
  7. The research work of the thesis include mainly : ( 1 ) observe a phenomenon which the two fracture modes are simultaneously found near crack tip of a four - point - bend specimen when the ratio of m / q is close to 3. 0mm, criteria m / q, when the fracture mode of four - point - bend specimen transits from void - mode to shear - mode. intensely location plastic distortion is observed in the front of crack tip and the macro - fracture of the specimen with the same m / q belongs to shear - mode fracture

    本文主要在以下幾個方面取得了一定進展:通過四點彎試件斷口和切試驗,觀察到紋尖端同時存在種斷機制? ?在種斷模式相互轉化臨界狀態附近,紋前方既鈍化和延伸區中空穴形核擴張,又銳化角前劇烈集中剪切變形。
分享友人