有效余氣量 的英文怎麼說

中文拼音 [yǒuxiàoyúqìliáng]
有效余氣量 英文
functional residual capacity
  • 有 : 有副詞[書面語] （表示整數之外再加零數）: 30 有 5 thirty-five; 10 有 5年 fifteen years
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 有效 : effective; valid; efficacious
  • 氣量 : 1 （容忍謙讓的限度; 度量） tolerance 2 （舊指才識和品德的高低） ability and insight; 氣量表 gas m...
  1. 2. recuperative gas turbine cogeneration with water injection and its thermodynamic analysis recuperative gas turbine cogeneration can reduce exhaust temperature, make use of waste heat and increase efficiency

    二、功熱並供回熱注水燃氣輪機及其熱力分析採取回熱和功熱並供可以減小熱機循環的當量排氣溫度或有效利用余熱。
  2. Our factory by produces the air current spinning machine fitting product ( reeling thread, transfers cup, divides combs roller, pressure roller and so on ) primarily, while expands, the enhancementproduction scale, efficiency unceasingly, strives for the survival by the quality, does not hesitate the great riches to increase or to renew the equipment, purchases the domestic and foreign advanced precise numerical controls lathe, the processing center, the high accuracy grinder successively and so on hundred, causes the product quality and the processing craft has the good stability and thereliability

    工廠以生產氣流紡紗機配件產品（紡紗器、轉杯、分梳輥、壓輪等）為主，在不斷擴大、提高生產規模、效率的同時，以質量求生存，不惜重資增加或更新設備，先後購進國內外先進的精密數控車床、加工中心、高精度磨床等百余臺，使產品質量和加工工藝具有良好的穩定性和可靠性。
  3. 3. on boiler retrofit, the calculation of fuel burning, the heat calculation of boiler inside structure and convection section, and the design of structure parameter of feed water heat exchanger are made. the flue gas channels " resistance calculation and the boiler strength verifying are also carried out. replacement of water cooling wall improves heat exchanging and decreases loss of heat radiant

    對鍋爐本體進行了燃料燃燒計算、爐膛結構熱力計算、對流受熱面結構熱力計算、鍋爐給水加熱器結構參數設計、煙道阻力計算及鍋爐元件強度校核等；改進了水冷壁布置使換熱效果更好，減少輻射換熱損失；改進對流段結構，更充分的利用爐膛出口煙氣余熱，提高熱效率；並且進行了煙氣阻力計算、熱效率計算和能量平衡測試，對改進后的稠油燃料和改進前進行了對比，燃燒狀況和熱效率有明顯改善。
  4. The paper mainly discussed the reasons of stress from liquid ammonia pressure vessel causing crack through examing data and experimental results and analysing relevant referential documents and materials, taking 1200 ammonia vessel ' s crack and leaking in a certain fertilization company as an example : there existed remaining welding, stress in the equipment ; there existed a stress decaying surrounding, i. e., moisture 0. 2 %, and temperature > - 5 with o2 or co2 inside ; the higher the intensity of raw materials, more possible it was to have stress decaying crack

    摘要以某化肥公司1200氨冷器殼體開裂泄漏的失效分析為例，通過對檢驗數據和結果及有關文獻資料的分析研究，探究了液氨介質壓力容器產生應力腐蝕裂紋的原因：設備中存在較高的焊接殘余應力；液氨介質具備應力腐蝕環境，即含水量0 . 2 % ，且有空氣（ o2或co2 ）污染（或摻入） ，使用溫度高於零下5 ；母材強度越高，應力腐蝕裂紋產生的傾向就越大。
分享友人
分享到 Line

分享到臉書