有翼緣的 的英文怎麼說

中文拼音 [yǒuyìyuánde]
有翼緣的 英文
flanged
  • 有 : 有副詞[書面語] （表示整數之外再加零數）: 30 有 5 thirty-five; 10 有 5年 fifteen years
  • 翼 : Ⅰ名詞1 （翅膀） the wing of a bird 2 （像翅膀的東西） the wing of an aeroplane etc : 鼻翼 wing of...
  • 緣 : Ⅰ名詞1 （緣故） reason 2 （緣分） predestined relationship 3 （邊） edge; fringe; brink Ⅱ動詞（攀...
  • 的 : 4次方是 The fourth power of 2 is direction
  1. Based on basic principles of grillage method, an improved grillage model of wide cantilevers bridge deck is brought forth and its effectiveness is verified after generalizing rules of grillage meshing and sectional characteristic

    基於梁格法的基本原理，提出了寬翼緣上部結構分析的改進梁格模型，並總結了梁格單元劃分和截面特性計算的一般方法，最後通過算例驗證了該模型和方法的有效性。
  2. It is the key of ebfs, therefore, furthermore calculation about link are carried out in this thesis, introduced achieved research, summarized the affect of link on whole capability in the first, the second, numerical calculation are proceeded on link with ansys : with the purpose of discussing yielding mode critical length of link, established five different specimens ; with the purpose of discussing the influence of h / tw of web, b / tf of flange and h / b, established eighteen different specimens ; with the purpose of discussing the affect of stiffener, established four different specimens, and elaborated the affect of stiffener on link based on achieved test researches

    因此，本文對耗能梁段進行進一步計算分析，概述耗能梁段對整體性能的影響，並利用有限元程序ansys對耗能梁段進行數值計算：針對耗能梁段的屈服類型建立5種不同長度的模型，計算討論耗能梁段屈服類型的長度劃分；針對耗能梁段腹板高厚比、翼緣寬厚比以及梁段截面形狀等因素共建立了18種模型進行計算分析；針對加勁肋對耗能梁段的作用建立了4種模型，並結合已有的試驗闡述了加勁肋對耗能梁段的影響。
  3. Both flange and web exhibited satisfactory elongation characteristics (i. e. 28%).

    翼緣和腹板都有令人滿意的延伸率（即28）。
  4. Furthermore, in order to predict the force at beam tension flange when end - plate yields, kulak method, applied to determine the ultimate strength of the t - stub connections, are modified by introducing a parameter c. the general solution of parameter c is also provided in this paper

    在有限元計算的基礎上，本文分析了影響節點強度的主要因素，包括： （ 1 ）螺栓和端板的強度； （ 2 ）柱翼緣的抗壓強度； （ 3 ）柱腹板的抗壓強度。
  5. On the basis of this, the paper makes a great deal of calculation and analysis in this part, different parameters " effect and stress gradient are included. local buckling coefficient and the efficient width calculated formula are provided and look forward to take a reference to the redaction of the specification

    本文對此內容進行了較為深入的研究，考慮了多個參數的影響，對各種應力比作用下的楔形腹板的屈曲及屈曲后強度進行了計算分析，得出了考慮翼緣相關作用的楔形腹板屈曲系數及有效寬度系數的計算公式，以期為規范的修訂提供參考。
  6. The main popular theoretical method adopted to study end - plate connection is finite element technique under monotonic loading at present. this paper applies nonlinear ( material, geometry and contact ) finite element method to analyze the behaviors of connections under cyclic load at fist time. contact elements are set between end plate and column flange, screw cap and neighborhood plane, bolt bar and hole

    對于端板連接的理論分析，目前國內外的研究主要局限在單向加載有限元分析范疇，本文首次採用三維非線性（包括材料、幾何與狀態非線性）有限元對端板連接進行了循環加載分析，端板與柱翼緣間、螺栓頭（帽）與相鄰板件間、螺栓桿與孔壁間都設置了反映邊界狀態的接觸單元。
  7. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  8. At the top flange there would be enough slack so that no relative twist of any significant magnitude would be introduced into the girder web.

    在上翼緣處有足夠的松動，因而在主梁腹板上並不會引起很大的相對扭轉。
  9. Results showed that the ductility of bolt spjice is much better than welds, weaker splice joints develop larger plastic deformation, slipping between faying surfaces, bearing of bolts to hole surfaces and buckling of splicing plates are all ideal energy dissipation mechanism

    試驗結果表明：螺栓拼接節點的延性遠好於樑柱焊縫連接；較弱的拼接節點產生較大的塑性變形；接觸面的滑移、螺栓與孔壁的擠壓和翼緣拼接板的屈曲都具有良好的耗能能力。
  10. As is well known, the effective width depends on several factors, such as the cross - section width, the height of web, the spacing of span and so on. we can conclude that width / span ratio ( overhang width / span and central width / span ) is the governing factor of the effective width

    影響箱形截面樑上翼緣有效寬度的因素很多，如上翼緣寬度、梁高、跨度以及結構體系等，通過大量計算表明寬跨比[翼緣部分寬度、箱室部分寬度與跨度的比值]是有效寬度的控制影響因素。
  11. In this paper, the researching and developing situating at home and abroad on aseismic properties of the masonry structures are reviewed. aiming to the defects of the calculated formulas of the aseismatic shear strength of brick walls in the code for seismic design of building ( gb50011 - 2001 ) and the code for design of masonry structures ( gb50003 - 2001 ), through test on brick wall models between the single wall and the wall with flanges, restoring force characteristics, the behavior at failure of the brick masonry wall and the effect of longitudinal wall under cyclic horizontal loading were analyzed the aseismic capacity has increased by 31 % for wall with flanges, the rigidity and deformation of the wall has gone up greatly too. the conclusion that the effect of longitudinal wall should be comprised in the aseismatic formulas was proposed

    本文回顧了國內外關于砌體結構抗震性能的研究與發展現狀，針對建築抗震設計規范（ gb50011 - 2001 ）和砌體結構設計規范（ gb50003 - 2001 ）中墻體抗震驗算公式中的不足之處，通過單片墻和帶翼緣墻在垂直荷載和水平反復荷載作用下的對比試驗，研究了帶翼緣墻在水平反復荷載作用下的恢復力特性曲線、磚墻破壞特徵以及縱墻的影響等，翼緣墻的存在，主墻抗剪能力可以提高31 ，剛度及變形能力也均有較大提高的結論，墻體驗算公式中應當考慮縱橫墻共同作用的影響。
  12. This paper applies nonlinear finite element program bsnfem to analyze the behaviors of eccentrically braced steel frames under cyclic load. the study that comprehensive and systematic analyze the factor of links length, thickness of links flange, distance of links rib, thickness of links rib and angle of brace to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel frames have been some studied before. this paper fills the black in the filed factor of high - span ratio, brace stiffness and brace - to - beam connections to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel trames and any factor to be changed affect energy - dissipation capacity of y shape eccentrically braced steel frames

    對耗能梁段的長度、耗能梁段腹板的厚度、耗能梁段翼緣的厚度、耗能梁段加勁肋的間距、耗能梁段加勁肋的厚度、支撐的夾角等因素的改變對d形、 k形偏心支撐鋼框架耗能的影響，前人已有一些研究，本文對這些因素的影響進行了全面系統的分析，完善了理論分析的不足；而結構高跨比、支撐剛度、支撐與梁的連接形式等因素對d形、 k形偏心支撐鋼框架破壞機理的研究以及各種因素對y形偏心支撐鋼框架破壞機理的影響，則很少有人涉及，本文對此也進行了深入系統的分析，填補了這一研究空白。
  13. There are not definite code provision of evaluation of effective width about steel box - girder in many countries, especially curved bridge because its evaluation of effective width vary with the radius of the curve

    目前許多國家對于鋼結構箱形樑上翼緣有效寬度的取值都沒有明確規定，尤其是曲線梁橋由於其有效寬度的取值受曲線半徑的影響，其結構更趨復雜。
  14. In this paper, the practical tables calculating the effective width of different structures are provided to perfect formulation concerned in the standard

    本文對不同結構型式的鋼結構箱形樑上翼緣有效寬度進行分析，為完善規范有關有效寬度的內容提供依據。
  15. Thirdly, in term of the results of testing and calculation, the displacement and libration, the difference of altitude, the flexibility and strain of crane - beams are all generally analysed, especially the reason why the crane - beams are attaint is lucubrated, and the reasons why the trigging pole is ruptured, the upper wingspan is damaged, the orbital movement, the exceptional incline of colums are open out, which has instructional significances that improve the design of the steel frame of the coke made by dry flameout

    第三，根據檢測和計算結果，對鋼框架的位移和振動、框架高差、吊車梁撓度和應變等進行了全面的分析，特別對吊車梁系統的損傷原因進行了深入分析，揭示了制動桿件斷裂、上翼緣磨損、軌道竄動、柱異常傾斜等一系列損傷現象的原因，對于改進干熄焦鋼框架的設計有著直接的指導意義。
  16. With the backing force of hongrun steel company, our products cover various models of angle steel, channel steel, frange plate and i steel

    依託唐山宏潤鋼鐵有限公司的強大後盾，我們的產品包括全部系列型號的角鋼、槽鋼、翼緣板、工字鋼等。
  17. Their availability, stability, and robustness are proved by simulation on both model rotor and real rotor with the effect of the design parameters of the flap studied

    對模型與真實旋翼進行模擬計算並研究后緣附翼設計參數的影響，結果表明兩種方法都具有較好的有效性、穩定性和魯棒性。
  18. In addition, the dynamic equation of the rotor with trailing edges and the 2 - x actuator has been modeled for analyzing the aerodynamic performance of the rotor. the result of the analysis tells us that the performance of the rotor with trailing edges can get a remarkable improvement

    進而研究旋翼動力學模型，將推挽式雙x驅動器模型作為后緣附翼的一種驅動機構，分析旋翼的氣動性能，模擬運算結果表明，后緣附翼智能槳葉在各方面的性能都有顯著的提高。
  19. Gabled frames are widely used in industry and civil engineering, it ' s web plates " local buckling calculated formula in the technical specification for steel - structure of one - storey light - weight buildings with gabled frames ( cecs102 : 98 ) are based on the rectangular plates " and did n ' t consider the interaction of the fringe plate. so, there are some different between the actual members and the prescript of the specification, and the post - buckling strength ' s calculated formula is based on the local buckling ' s, it must have some unreasonable

    楔形門式剛架廣泛地應用於工業與民用建築中， 《門式剛架輕型房屋鋼結構技術規程》 （ cecs102 ： 98 ）中楔形腹板局部屈曲的計算公式來自矩形板，並且沒有考慮翼緣的相關作用，因此，規程中的規定與構件的實際工作狀況有一定的差異，且屈曲后強度的計算公式也是以局部屈曲系數為基礎的，勢必有其不合理性。
  20. In elementary beam bending theory, it is assumed that the stresses are constant through the width of the beam. however, for the wide flange girders, the stresses are not uniform

    按照初等梁理論即假定翼緣板具有無限抗剪剛度，寬翼緣箱梁在荷載作用下翼緣的正應力沿著寬度方向上是均勻分佈的。
分享友人
分享到 Line

分享到臉書