有限元素法 的英文怎麼說

中文拼音 [yǒuxiànyuánsùfǎ]
有限元素法 英文
fem （= finite element method）
  • 有 : 有副詞[書面語] （表示整數之外再加零數）: 30 有 5 thirty-five; 10 有 5年 fifteen years
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 素 : Ⅰ形容詞1 （本色; 白色） white 2 （顏色單純） plain; simple; quiet 3 （本來的; 原有的） native Ⅱ名...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 有限 : limited; restricted; finite; a little; not much
  1. J. r. hendershot and t. j. e. miller, “ design of brushless permanent magnet motors, ” magna physics publishing and clarendon press, 1994

    黃昌圳，有限元素法簡介，高性能無刷馬達設計技術研討會講義， 2003 。
  2. With the development task background of ctr200g precision centrifuge, the acceleration error factors of centrifuge system are qualitatively analyzed theoretically at first and also quantitatively calculated by means of finite element method, therefore, the structural optimum design problem of the load pan is proposed

    論文以「 ctr200g型精密離心機」的研製任務為背景，首先從理論上對引起離心機系統加速度誤差的因素進行了定性分析，並且採用了有限元方法對其進行了定量計算，由此提出了負載盤結構優化設計的問題。
  3. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  4. ( 2 ) respectively by elastic theory analyses and methods of structural mechanics, transverse static analytical equations for flexible pipeline rigid pipeline are established whose outcomes are applied in numerical example to compare those with that by finite element method. ( 3 ) considering interaction of filled soil, pipeline and foundation, with an eye to non - linear soil model, in view of the initial geo - stress field and the effects of interface between soil and pipeline, and by finite element method the calculational model and method are built for transverse stress in pipeline. then, by the great finite element analytical software ansys, those outcomes are applied in calculation example of positive buried pipe to educe the distribution of circumjacent soil pressure and stresses on cross section and to compare it with that calculated by conventional ways before those outcomes are applied in engineering case of positive buried pipe with flexible filled materials to confirm distribution of soil pressures after the measure for reduction and to compare it with measurements. as a result, the model set up in this paper is proved to be applicable after all above - mentioned analyses

    本文基於彈性理論和有限元原理與方法，分析了上埋式地下管道橫向力學計算方法和性狀並探討了上埋式地下管道的減荷等問題： （ 1 ）在分析現有幾種典型的管道垂直土壓力計算方法的基礎上，探討了影響垂直土壓力的主要因素以及改進的方法； （ 2 ）分別通過彈性理論分析法和結構力學的方法，建立了地下管道柔性圓環和剛性管涵的橫向靜力計算方程，並應用在算例中，把所得結果和有限元方法所得結果進行對比分析； （ 3 ）考慮填土、管道和基礎的共同作用、土體的非線性特性、初始應力場以及土體和管道的接觸面因素的影響，利用有限元的思路，建立了地下管道橫向力學有限元計算模型和方法，並且採用大型有限元分析軟體ansys ，針對上埋式管道工程算例，得出了管周土壓力以及管道橫截面應力的分佈狀況和規律，並和理論值進行對比；針對施加柔性填料的上埋式管道工程實例，得出了減荷后的土壓力分佈，並和實測值進行了對比。
  5. The image reconstruction technique based on the finite element method is flexible and easily to use for many applications

    採用有限元素法計算逆時影像重建的技術經證實是可行且易於應用於其他的研究領域。
  6. At first, the recent development of the simulation to cargo system of chemical ship is introduced. the significant of the research, methods and the characteristics of system simulation are also discussed. the model of cargo liquid and ballasting pipeline network is then simulated by the methods of predecessors

    文章首先介紹了散裝化學品船液貨系統模擬發展的現狀，闡述了化學品船液貨系統模擬研究的意義，以及模擬的方法和特點；之後運用前人的管網有限元方法對母型船液貨、壓載管網進行模擬建模，在系統地考慮了多種因素的前提下，實現了化學品船液貨系統操作動態模擬和靜態模擬。
  7. The foundation engineering is typical in both excavation depth and scale, on the basis of in - situ investigation, the design optimistic of retaining wall was discussioned in this paper, the mian reseaches including : the using of fem optimazition methods of rods system ; the delvopment of programs for optimazition of imbedding depth of structure based on matlab and for whole design optimaziton of the retaining structures based on ansys, under the two controlling factors of the saft coefficient and the reliability probability about the whole damage of retaining atructure ; the analysis on the m index of soil, the depth of retaining structures imbedded in the rock and the overall optimistic design of retaining structures

    該基礎工程不論在開挖深度還是規模上都很具有代表性。作者在現場調研的基礎上，探討了基坑支護結構設計優化問題。主要研究內容可以歸納為：應用基於m法的彈性地基梁桿系有限元方法；在圍護結構整體穩定性安全系數與可靠性破壞概率兩種控制因素下，編寫了嵌巖深度優化的matlab程序與圍護結構整體設計優化的ansys批處理程序；進行了地層抗力比例系數反算、地下連續墻嵌巖深度優化與地下連續墻結構體系整體設計優化。
  8. Our study uses finite element method and conducts analysis of the coupled thermo - hydro calculations. the effect due to water saturation is discussed and compared with experiment results of buffer material

    本研究採用有限元素法，進行熱?水力耦合之效應分析，針對緩沖材料試驗試體進行實驗結果之驗證以及討論。
  9. C. l. chang, 1998, shape optimization of pressure vessel using conventional optimization and taguchi method, canadian society for mechanical engineering forum, toronto, canada

    張嘉隆，林俊宏， 1998 ，有限元素法于壓力容器插管加強扳設計之應用， 87年機械基礎學術研討會論文集，陸軍官校
  10. This dissertation concentrates on the difficult problems that the pipeline or pipe defects are not estimated or evaluated quantitatively, intelligently by mfl ( magnetic flux leakage ) inspection method. from the practical demand, theoretical analysis and experiments or testing, the mfl inspection technology of pipeline or pipe defects are explained, summarized in detail in the whole paper, at the same time, the relationship between the mfl field distribution, the mfl signal shape and the defect geometry or severity, the analysis of the mfl data and the compensation of influencing the relationship factors, signal feature extraction, intelligent recognition of defect parameters and so on are studied systematically

    論文針對管道（鋼管）缺陷漏磁檢測定量化、智能化的難題，緊密結合檢測現場實際需要，通過理論分析和大量實驗，系統分析總結了管道（鋼管）缺陷漏磁智能檢測技術，並在缺陷漏磁場分佈以及缺陷漏磁信號與缺陷外形參數間的關系、缺陷漏磁信號分析、漏磁信號影響因素補償、缺陷漏磁場波形特徵提取和缺陷外形尺寸定量識別等方面進行了深入研究，主要成果和創新如下：引出磁偶極子模型近似分析常見缺陷漏磁場，針對磁偶極子模型的不足，將有限元方法應用到缺陷漏磁場分析，實現了常見管道樣本缺陷漏磁場的模擬。
  11. Topics include : mathematical formulations ; finite difference and finite volume discretizations ; finite element discretizations ; boundary element discretizations ; direct and iterative solution methods

    課程主題有：數學列式、有限差分與有限體積離散、有限元素離散、邊界元素離散、直接與疊代解法。
  12. The finite element method was used to calculate elastic wave propagation in the medium

    本文採用有限元素法計算彈性波在介質中的傳播。
  13. Keywords : micro - cantilever sensor, mechanical model, piezo - resistive materials, finite element method

    關鍵詞：微懸臂梁感測器、力學模型、壓阻材料、有限元素法。
  14. Finite element method ( fem ) occupies an important part in computer aided engineering ( cae ) methods

    有限元法，也稱有限單元法或有限元素法，在計算機輔助工程cae中佔有重要的位置。
  15. With the rapid development of the computer techniques, the finite element method and its application would be used in more and more engineering design fields

    隨著計算機技術的飛速發展，有限元素法及其技術在工程設計中的應用更加廣泛。
  16. Alavizadeh, a. r., zargari, a., grise, w. r, ” the application of ansys software in analyzing and predicting thermal behavior ” electrical insulation conference and electrical manufacturing & coil winding conference, 1999. proceedings 26 - 28 oct. 1999

    卓玉娟， "有限元素法在汽車碟式剎車制動器之分析與應用」國立中興大學，土木工程學系， 2003年。
  17. The finite element method ( fem ) has become an important means in modern engineering designs, which is used in many fields, such as structural stress analysis, deformational stiffness analysis, mechanic failure analysis, dynamic process analysis, heat analysis, electromagnetism filed analysis and so on

    有限元素法已成為工程設計中不可或缺的重要技術手段，在大型結構作用力分析、變形分析、失效分析、動力學分析、傳熱分析、電磁場分析、流體流動分析等方面扮演著越來越重要的角色。
  18. In this topic, the error characteristic of resistance voltage sensor was analyzed in theory, by using electric circuit analysis, the reasons which affected its error were gotten. based on theory analyses, initial structure was designed. then by using fem ( finite element method ) of simple resonance field, several structures electromagnetic field was calculated, and their amplitude errors, phase errors, maximum of electric field intensity and frequency characteristic of amplitude error were contrasted

    本文從理論上分析了電阻式電壓傳感器的誤差，用電路分析法定性的研究了影響電阻分壓器誤差的因素；在理論分析的基礎上進行了電阻分壓器結構的初步設計；基於該設計，利用簡諧場的有限元方法進行了場的計算，比較了幾種結構方案的幅值誤差、相角誤差、最大場強值及其幅值誤差的頻率特性，從而得到一種最優方案；製作了分壓器樣機，並在本實驗室進行了實驗；最後，對電子電路部分進行了初步設計，並提出了抗干擾的措施。
  19. C. l. chang, 1998, a study of undergrduate finite element currculum in taiwan, canadian society for mechanical engineerng form, toronto, canada

    張嘉隆，劉坤孝， 1998 ，整合實驗應力量測與有限元素方法機械元件之應力分析， 87年機械基礎學術研討會論文集，陸軍官校
  20. Fepg uses the method of components and the technique of artificial intelligence to generate finite element program automatically by a computer according to the general principles of mathematic and internal rules of finite element method, as is similar to the deduction of mathematics

    有限元程序生成系統可以根據通用的數學原理和有限元素法規則，採用部件化和人工智慧的方法，像推導數學公式那樣利用計算機自動生成有限元程序。
分享友人
分享到 Line

分享到臉書