有限失效集 的英文怎麼說

中文拼音 [yǒuxiànshīxiàojí]
有限失效集 英文
finite failure set
  • 有 : 有副詞[書面語] （表示整數之外再加零數）: 30 有 5 thirty-five; 10 有 5年 fifteen years
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 集 : gatherassemblecollect
  • 有限 : limited; restricted; finite; a little; not much
  1. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
  2. This paper trice to find the cause of effective ness loss and to analyze it theoretically by adopting the ways of quantitative analysis and quantitative analysis by using the way of fault tree to carry out the qualitative analysis, it draws the logic charts by various elements that cause the loss of effectiveness and to make a faucet tree to find out the loss programs, then make a final analysis of the smallest element of the fault tree. the first problem is due to the over friction by exceeding permitted limits ; the second problem is due to the gear feather ' s low inteusity, this paper adopts the method of changing the trans mission ratio of the first gear and the width of the sixth gear of second shaft so as to solve the problems

    本文採用定性和定量相結合的方法，利用失效樹進行定性分析，它通過對可能造成系統失效的各種因素，畫出邏輯框圖，從上到下繪成失效樹，找出失效譜，並對失效樹的全部最小割集進行分析，找出有可能的失效原因，再對其通過理論計算進行定量分析，由此發現第一個問題是由於離合器在極限狀況下的滑磨功超過其許用值造成的，第二個問題的原因是二軸六檔齒輪強度不足。
  3. According to the actual structure and the real size of the defective bus, this thesis has accurately established the bus body frame model using the board - shell element, carried on the analysis of the body frame strength and stiffness, and obtained the stress distribution and concentration result of the bus body frame. finally we found the reason, which causes the body frame early failure problem

    本文根據問題客車的實際結構和尺寸準確地建立了全板殼單元大客車車身骨架有限元計算模型，對車身骨架的強度和剛度進行分析，得到了全板殼元客車車身骨架模型的應力分佈與應力集中結果，找出了車身骨架早期失效的原因。
分享友人
分享到 Line

分享到臉書