材料熱力學 的英文怎麼說

中文拼音 [cáiliàorèlìxué]
材料熱力學 英文
thermodynamics of materials
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 學 : Ⅰ動詞1 （學習） study; learn 2 （模仿） imitate; mimic Ⅱ名詞1 （學問） learning; knowledge 2 （學...
  • 材料 : 1. （原料） material 2. （資料） data; material 3. （適于做某種事的人才） makings; stuff
  1. This article choosed out organic phase change materials, and, the solid - liquid - equilibrium of eleven binary system including fatty alcohol / fatty acid, n - octadecane / fatty acid, n - octadecane / fatty alcohol system were determined by cooling curve, and, t - x phase diagrams of these systems were drawn. the result shows that all these systems are simple eutectic, at the same time, the entropy of phase change of every system in the eutectic point is determined by using differential scanning calorimetry ( dsc ). and n - octadecane / fatty acid systems were calculated theoretically

    本文初選出部分有機相變貯能材料，採用步冷曲線法測定了12醇-羧酸系列、 18烷-羧酸系列、 18烷- 12醇體系共11組體系的二元固液相平衡關系，繪制了這11組體系的t - x相圖，測定結果表明，這幾組體系均為簡單低共熔體系；同時利用差熱掃描量熱法（ dsc ）對上面各組體系低共熔點處的相變焓進行了測定；並對18烷-羧酸系列進行了熱力學理論預測。
  2. It could be found that mmt was partially exfoliated and partially intercalated in the matrix. a proper amount of mmt could improve the mechanical and thermal propertied of the pvc / ( pb a - mmt ) nanocomposites

    發現mmt形成了部分剝離部分插層的結構，並且適量mmt的加入可以提高復合材料的力學性能和熱穩定性。
  3. Tem images revealed that the phase morphology of pls composites were influenced by the interaction among the matrix, the compatibilizer and organo - mmt. hence, a novel mesophase " " silicate sheet cluster " was also found in ldpe / eaa / mmt nanocomposite. the mechanical, barrier and thermal properties results of ldpe / mmt composites indicated that,

    對ldpe mmt納米復合材料的力學性能、透氣性能以及熱力學性能的研究結果表明，插層型或剝離型pls納米復合材料的力學性能取決于基體、相容劑在硅酸鹽片層表面的相容性。
  4. In this investigation carbon black - filled electrical conductive composites of poly ( ethylene terephthalate ) / polyethylene were first prepared through the single - screw melt - blended extrusion, then drawing, followed by the quenching and subsequent press molding. the relationships among the influencing factors including composition, hot stretching ratio and compatibilizer, morphology and properties of composites were systematically investigated. positive temperature coefficients effect and crystallization behaviors of composites were preliminarily analyzed

    本文擬採用單螺桿熔融共混擠出?熱拉伸?淬冷的新的成型方法制備炭黑填充的pet pe復合導電材料，熱拉伸的目的是使材料的分散相（ pet相）在加工過程中原位形成纖維，而炭黑基本分散在纖維中或纖維的表面上，使炭黑粒子間間距減小，形成更多的導電通路，從而提高材料的導電性能，同時保持或提高材料的力學性能。
  5. As the content of vermiculite minerals was about 3 %, the impact strength ( nick ), the flexural strength and the heat distortion temperature ( hdt ) of the nanocomposites all were the lowest and decreased 21 %, 28 %, 3c, respectively. compared with those of the polybenzoxazine ( bisphenol a type ), its thermal expanded coefficient ( tec ) was 3. 4 % bigger than that of the polybenzoxazine ( bisphenol a type )

    雙酚a型ben蛭石納米復合材料的力學性能和熱性能表現出明顯的結構特徵，普遍地低於純樹脂的性能數值，而優于雙酚a型ben金雲母復合約zi和zs 「熱變形溫度dt ）低約3 ，線膨脹系數高約3
  6. Main curricula : thermodynamic of material, crystal structure and the technology of x - ray, the principle of the solid state phase transition, the force behavior of material, metal material science, surface engineering, mate and engineering, the application of computer in material science

    主要課程:材料熱力學，晶體結構和x射線學，固態相變原理，材料力學性質，金屬材料學，表面工程，材料成型原理與工藝，計算機在材料科學中的應用
  7. Mechanical property, thermal - oxidative - ageing property, flame retardancy and dynamic mechanical analysis ( dma ) of nanocomposites have been studied, and a comparison between nanocomposites and carbon black reinforced rubber was made

    研究了納米復合材料的力學性能、熱氧老化性能、阻燃性能和動態粘彈性等，並與炭黑補強膠料的一系列性能進行了比較。
  8. Neutron scattering technology is widely used in many research reactors in the world, whose applications include microstructure analysis, material dynamics, fundamental physics and so on, especially, very popular research of new material and new biological medicine in recent years

    中子散射實驗技術在全世界許多研究堆上得到了廣泛的應用，其應用范圍包括物質微觀結構分析、材料動力學、基礎物理等，尤其可應用於近些年來較為熱門的新材料和新生物醫藥研究。
  9. The results of static firing test shows that the thermal erosion properties, mechanical properties, tand thermal shock resistance of the c / sic composites can meet a demand for thermal - structure application in the area of aerospace such as liquid rocket thruster

    試驗發動機地面熱試車結果表明，該c / sic復合材料的力學性能、燒蝕性能和熱震性能優良，可滿足宇航工程中諸如液體火箭發動機推力室等對熱結構材料的使用性能要求。
  10. In the paper, active control to rotor vibration with sma is studied : 1 ) the material performance of sma, especially the coupled relation of strain, stress and temperature, is studied in nonlinear coupled thermoelasticity theory and the linear result is modified ; 2 ) the nonlinear dynamic behavior of rotor system with sma bearing is studied in the nonlinear theory and the dynamic stability theory and the deference of the soft / hard nonlinear system is pointed out

    1 ）運用非線性熱彈性耦合理論研究記憶合金材料的力學性能，特別是應力、應變和溫度三者之間的耦合關系，改進了原有的線性結果。 2 ）運用非線性理論和運動穩定性理論研究帶有記憶合金支承的轉子系統在非定常狀態的非線性動力學行為，指出了軟、硬非線性系統的區別。
  11. Main research direction contains nano material thermodynamics, the metal alloy of shape memory, fuel cell and engineering material of automobile etc

    主要研究方向有納米材料熱力學、形狀記憶合金、燃料電池和汽車工程材料等。
  12. Based on the construction schedule and thermodynamics parameters of certain rcc arch dam, the temperature and stress fields during construction and service are simulated and computed, and also the computation results are compared with the practical observation data ; the comparison results show that the computation results are reasonable

    根據某工程碾壓混凝土拱壩施工過程和材料熱力學試驗參數，進行了施工期和運行期溫度場和應力場模擬計算，計算成果與施工期觀測資料進行了對比分析，二者吻合較好。
  13. Interfaces in fiber reinforced composites ( frc ) are vital because they ensure stress transfer between matrix and fibers. to characterize the interfacial properties in a fiber reinforced composites, several micromechanical experimental techniques have been developed

    纖維增強復合材料中，纖維和基體在外載作用下的破壞問題一直是復合材料力學性能研究的熱點，所以纖維和基體之間的界面對復合材料的力學性能起著至關重要的作用。
  14. Finally, the pmma / sio2 micron - composites was prepared by in - stu polymerization, and the properties of this composites filled with different surface characteristic and content ratio white carbon was study. the results revealed that improving interfacial compatibility and strength between micron - white carbon and polymer were beneficial to improving the mechanics, thermal stability and resistant solvent

    結果表明：對于微米級的白炭黑粒子，提高其與聚合物基體的界面相容性和界面強度，對復合材料的力學性能、熱穩定性以及耐溶劑性能有很好的改善。
  15. The test results show that two kinds of heat treatment can increase mechanical properties of the material in different degrees, but cannot improve corrosive wear resistance property under the condition of wet wear

    試驗結果表明：這兩種熱處理工藝可以不同程度地提高材料的力學性能，但不能改善材料在濕式磨損時的耐腐蝕磨損性。
  16. Curing agents and mixing conditions were two important factors that effected on exfoliation behavior of organophilic montmorillonite in diglycidylether of bisphenol a matrix. the organophilic montmorillonite was exfoliated completely and there were no d001 diffraction peaks with methyltetrahydrophthalic anhydride as curing agent and benzyldimethylanine as catalyst. properties test results show that mechmical properties, electricity properties, heat distortion temperature of the exfoliated nanocomposites were all improved by addition of the montmorillonite, and the nanocomposites had lower linear thermal expansion coefficiency and water absorption compared with neat epoxy resin

    結果表明，環氧樹脂與有機蒙脫土的相容性好；混合條件和固化劑是影響有機蒙脫土在環氧樹脂中剝離的兩個重要因素，在一定的混合條件下並選用合適的固化劑可以使蒙脫土在環氧樹脂中完全剝離；剝離型環氧樹脂蒙脫土納米復合材料的力學性能、電性能、熱性能以及吸水性能與純環氧樹脂固化物相比均有不同程度的提高和改善。
  17. The tensile stress - strain curves of composites were also simulated. based on the energy equivalence principle, the formula that could predict the modulus of elasticity of sfrmmc was educed by considering the effects of thermal residual stresses and fiber ' s orientation. calculating and analysis indicate that the thermal residual stresses in sfrmmc are spatially non - uniform

    計算和分析表明，金屬基復合材料中熱殘余應力的分佈是空間不均勻的，對復合材料的力學行為產生明顯的影響，與不考慮熱殘余應力相比，其模擬的復合材料應力?應變曲線與實驗曲線吻合得較好。
  18. The mechanical property and heat - resistant property of the three kinds of in - situ composite is mainly introduced

    重點介紹了這三類復合材料的力學性能和耐熱性能。
  19. In order to get stress analysis and assessment to these equipments, it is necessary to understand clearly the thermal - hydraulical behavor in - vessel of cefr

    為了能夠對這些大型部件及結構材料的力學應力分析和評定提供溫度和壓力載荷，必須對整個堆內的熱工水力行為有清楚的認識和把握。
  20. With the unique self - made cooling system, the ly12 is researched through the above method and the ultra - fine grain was obtained

    應用傳熱學和塑性力學理論分析了採用該方法制備棒狀超細晶材料的力學條件和變形條件。
分享友人
分享到 Line

分享到臉書