束準直器 的英文怎麼說

中文拼音 [shùzhǔnzhíqì]
束準直器 英文
beam collimator
  • 束 : Ⅰ動詞1 （捆; 系） bind; tie 2 （控制; 約束）control; restrain Ⅱ量詞（用於捆在一起的東西） bundle;...
  • 準 : Ⅰ名詞1 （標準） standard; guideline; criterion; norm 2 （目標） aim; target Ⅱ動詞1 （依據; 依照）...
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  1. Moreover, compensated for aberration of ball lens by designing phase compensating plate to get a higher energy utilization rate. third, combining with the light beam property of dwdm system, put forward taking fresnel lens array as fiber arrayed collimator, designed differently structured lens array and discovered the arrayed collimator loss property, which compared with the existing parameter of fiber collimator, embodies many advantages as arrayed collimator

    結合密集波分復用系統的光束耦合特點，提出用菲涅爾透鏡列陣做光纖陣列準直器，並設計不同結構的透鏡列陣，得出了該陣列準直器的光束耦合損耗特徵，與現有的光纖準直器的參數相比，體現出用菲涅爾透鏡列陣作陣列光纖準直器的諸多優勢。
  2. The position and size of the monochromator, focusing curvature radii and tilting angles of the germanium focusing monochromator under different different take - off angle, size and divergency of the second collimator and intensity loss due to the use of it were determined. the neutron flux at different wavelength, under different reflection and take - off angle of the monochromator and divergency of the first collimator, were given. the simulation on the aperture used for limiting beam size in front of the sample showed that, smaller the size of the aperture and further the distance from the aperture to the sample, greater the loss of the intensity and more serious the spread of the beam along vertical direction at the sample position which makes the practical sampling volume greater than expected

    用蒙特卡羅模擬方法對中子應力衍射譜儀的設計方案進行了優化研究，提出了一系列可供參考的數據：確定了單色器的位置、尺寸、垂直聚焦單色器在不同起飛角下的聚焦曲率半徑和傾角；討論了第二準直器的尺寸和發散，以及使用第二準直器造成的強度損失；給出了在不同單色器反射面、起飛角、中子波長和第一準直器發散度的情況下樣品處的中子注量率，以及多種組合情況下譜儀的解析度曲線；對限束方孔的尺寸、距離樣品遠近對強度損失和測量中的影響做了深入研究。
  3. Power coupling efficiency of semiconductor laser

    半導體激光器光束準直系統的功率耦合效率
  4. At first, the author analyzed some chief factors such as light beam drift and atmospheric turbulence that affect the precision of the laser collimation in brief. then, the author studied the plan of the laser collimation generating nondiffracting beam and automatic level system with high precision. at last, the author completed the measurement of the straightness guideway by using ccd ( charge coupled device ) as the receiver and computer imaging processing

    文章首先簡要地分析了激光自身漂移、大氣湍流等影響激光準直精度的主要因素，然後對系統的激光準直方案進行論證，並確定了無衍射光束的生成方案、高精度自動安平系統的結構方案，最後以ccd為接收器件，通過計算機圖像處理，完成對軌道直線性的測量。
  5. 3. because traditional coupling system composed with cylinder lens and focus lens has the disadvantages of difficult to encapsulation and modulate, a new practical method brings forward : the output light from laser diode is collimated using a section of optical fiber with the diameter of 600 m instead of cylinder lens, and a sphere ? end lens

    3 .針對由柱透鏡和聚焦透鏡組成的組合透鏡耦合系統中存在的封裝和調試困難等問題，提出了:用一段直徑為600 m的裸石英光纖代替柱透鏡，對半導體激光器輸出光束進行準直整形;用球透鏡光纖對準直后的光束進行聚焦，直接實現和光纖耦合，來代替聚焦透鏡和光纖耦合的環節。
  6. X - ray beam collimator x

    射線束準直器
  7. A collimating device is also designed in this paper, and the collimating coherent light is good proved by the followed experiments. the robot vision system ' s object reading experiment is also finished in this paper, all these proved that this novel robot vision system is feasible

    本文設計出用於半導體激光器的擴束準直機構，並成功獲得實驗所需的準直相干光，本文還成功完成了機器人視覺系統目標讀取部分的實驗。
  8. The methods of straightness measurement are mostly about a line, but the straightness of couple lasers is the mainly problem in the system. first the couple laser beams should be calibrated separately. then, the couple laser beams should be aligned, and it is the most important problem in the design

    現在直線度的測量方法多數是對一條直線的直線度進行測量，本文所要解決的主要問題是兩束激光的直線性校準，首先要分別對兩束激光器的直線性校準，然後將兩束激光調到一條直線上，這也是設計中的重點問題。
  9. Methods for determination of physical properties of tobacco and tobacco products - nominal diameter of cigarettes and filter rods using a laser beam measuring apparatus

    煙草和煙草製品物理特性測定方法.第2部分:用激光束測量儀器測定卷煙和濾嘴標準直徑
分享友人
分享到 Line

分享到臉書