板彎曲 的英文怎麼說
中文拼音 [bǎnwānqū]
板彎曲
英文
bending of plates-
To this type balsa, if rectangle thin plate element is sill used will has limitation
對于復合樁基分析,若仍然採用矩形薄板彎曲單元進行分析,就存在一定的局限性。Symplectic solutions of annular sector plate clamped along two circular edges with circumfluent coordinate treated as
環扇形板彎曲問題中環向模擬為時間的辛體系In this article based on vibration theory of the flexural plate, the frequency equation, the equivalent mass and radiation impedance are derived and further, design theory is introduced
本文從薄圓板彎曲振動理論出發,推導了這種階梯圓盤的頻率方程、等效質量、等效彈性和輻射阻抗,並進而提出了這種階梯圓盤的一般設計方法。The farina press brakes which are equipped with tms, are able to measure without any delay of the bending process, the real thickness of the sheet. this system is totally automatic and updates all of the bending parameters accoring to the new thickness aquired
裝有tms系統的法瑞納的折彎機能夠準確無誤地測量初薄板彎曲加工厚度,全自動系統可根據要求的厚度自動改變參數。Standard test methods for testing structural panels in flexure
檢驗結構板彎曲情況的標準方法Based on the generalized variational principle of the modificatory variables and substituent shearing strain field interpolation of the bending theory of the mindilin plate, this paper brings up the nine - node mixed plate bending element and adopts the sap2000 ? a large - scale finite element analysis programs. by the examples, we find the precision of the method is satisfying
在對轉換層厚板進行局部有限元分析時,本文提出了基於mindlin中厚板彎曲理論的修正的二類變量廣義變分原理和替代剪應變場插值方法的九節點厚薄板通用的板彎曲單元,並採用了sap2000有限元程序。Lastly the above stiffness matrix, the nodal variables of which are the dual of stress functions, is replaced by a new one with simple displacements vector regarded as unknown. such finite element satisfies homogeneous equilibrium equations and can pass the patch test as long as the original plane elasticity element can pass the corresponding patch test
所得到的板彎曲單元在單元內部滿足齊次平衡方程,並且只要原始平面彈性單元能通過常應變分片試驗則轉換得到的板單元一定能通過常曲率分片試驗。United solution method on four edges supported plate bending with boundary displacements
支座位移作用下四邊支承矩形彈性薄板彎曲統一求解方法The calculation of lacunaris elastic plane bending or torsioning stress concentration problem by collocation method
用配點法計算多孔彈性平板彎曲或扭轉應力集中問題Study on fatigue behavior of sandwich beams consisted of aluminum foam core under bending condition
含泡沫鋁芯的復合板彎曲疲勞行為的研究Eccentric licker - in or bend feed plate
梳棉機刺輥偏心或喂入板彎曲。Application of natural boundary element method to the bending problem of the elastic thin circular plate
自然邊界元法在彈性圓形薄板彎曲問題中的應用General solutions of bending problem for vlasov plates
符拉索夫板彎曲問題的通解The nonsingular boundary element method for the bending problem of reinforced concrete plate
無奇異邊界元解鋼筋混凝土板彎曲問題Implants for osteosynthesis - bone plates - method for determination of bending strength and stiffness
接骨用植入物.骨板.彎曲強度和剛度的測定方法Paper and board - determination of bending stiffness - resonance method
紙和紙板彎曲挺度的測定法Implants for surgery - determination of bending strength and stiffness of bone plates
外科植入物接骨板彎曲強度和剛度的測定Bending of rectangular plate with each edges arbitrary a point supported under a concentrated load
集中載荷作用各邊上任一點被支承的矩形板彎曲New solution system for plate bending and its application
板彎曲求解新體系及其應用Roofing. general details. bend break test of corrugated sheet
屋頂.波形板彎曲破裂試驗分享友人