板形放電器 的英文怎麼說

中文拼音 [bǎnxíngfàngdiànqì]
板形放電器 英文
plate discharger
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 放 : releaseset freelet go
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 電器 : electrical equipment [appliance]電器燈 electric appliance lamp; 電器乾燥爐 electrical drying furn...
  1. This paper discusses the designing and making of the dynamic testing systems of engine electronic control system. base on the construction and operation principle of santana 2000gsi m3. 8. 2 engine electronic control systems, design and manufacture led circuit of dynamic testing and fault imitating electronic control unit. on the inspect board, design and equip with motronic 3. 8. 2 ecu i / o measuring joints, design and set up obd - ii diagnostic communication link, design and install fuel pressure inspecting meter. depend on the obd - ii diagnostic communication link and ecu i / o measuring joints, this dynamic testing system can inspect engine electronic fuel injection system, distributorless ignition system, idle speed control system and evaporative emission control system, and can inspect m3. 8. 2 sensors, ecu and actuators, and can interrogate fault memory and erase fault memory ; and can analyse data stream ; and can carry out fault imitating. besides, this paper analyses sensors and actuators typical fault w aves

    2電控單元電路連接器設計製成輸入輸出電子控制檢測端子，並在檢測面板上布置了obd -診斷插座和燃油壓力表。使該動態測試系統能實現對電噴發動機的燃油系統、直接點火系統、怠速控制系統和燃油蒸氣排放控制系統的動態檢測；並通過obd -診斷座、 ecu輸入輸出檢測端子和故障模擬處理單元實現對電噴發動機電控系統各傳感器、電控單元、執行器進行故障碼讀取與清除；動態數據讀取和波形測試和故障模擬等。此外，本論文還分析了傳感器和執行器典型故障波形。
  2. In the electronic component drawing system, i use " vectorgraph " to magnify and minify the diagram without any distortion

    電路板元器件繪制系統採用「矢量圖」的方法實現了不失真的圖形放大和縮小。
  3. The circuit receives feedback signal of encoder, disposes it by pid and in the form of digit sends control signal which is transformed by d / a into analogue signal to servo amplifier, so further to control motors

    電路板接收碼盤反饋信號，通過內嵌的pid演算法，以數字形式給出控制量，經過d a轉化為模擬控制信號給伺服放大器，進而控制電機運行。
  4. " electronic 1c chip drawing system " provides many functions such as " modify the position of the component ' s diagram " " modify the color of the component ' s diagram " " magnify and minify the component ' s diagram without distortion " " change the type of drawing line " " edit some physical properties of the component " " copy and paste diagram of one component " " delete one or more component diagrams " " move more than one components " positions " " change the z _ order of the diagram, set it to back or bring it to front " " save the drawing of the electronic components to one file and the file extension name is *. brd " " print the drawing ". users can finish all these functions easily by clicking and dragging the mouse

    電路板元器件繪制系統主要完成了使用鼠標拖拽、鼠標點按的方式繪制電路板上各種常見的元器件圖形；編輯電路板上元器件圖形的位置；編輯元器件圖形的顏色；不失真的對器件圖形進行放大和縮小；編輯元器件圖形的線型；編輯電路板上各個器件的物理屬性（比如電阻的阻值大小、電容的容量大小、額定電壓等） ；復制已經繪制出的電路板上的器件；粘貼剪貼板上的器件；刪除單個或多個已經繪制出的器件圖形；同時改變多個器件圖形的位置；改變繪制區內各個元器件的zorder順序，也就是可以將層疊在一起的圖形置前或置后；把繪制的電路板器件圖保存到指定文件中；能打開、查看和修改保存的電路板器件圖；列印電路板器件圖。
  5. This voltage transformer has three poles and the iron is made of sheet. the body is fixed on the box cover by clamping. there have the primary and secondary bushing also on the box cover

    本系列電壓互感器的鐵心由條形矽片疊成，為三柱芯式，器身用鐵夾件固定在箱蓋上，在箱蓋上裝有一次及二次套管等，油箱用鋼板焊成，油箱壁下部裝有接地螺栓及放油塞，箱底有四個安裝孔。
  6. Detail specification for multi - contact circular electrical connectors for d. c. and low frequency applications - bayonet coupling non - barrier sealed, environment resistant with rear insertable, rear release, rear removable crimp contacts also barrier sealed with non - removable solder contact styles - full plus airframe fit assessment

    直流和低頻用多觸點圓形電氣連接器詳細規范.帶后可插入后釋放后可拆卸壓接觸點的無檔板密封耐環境影響及帶不可拆卸釬焊觸點的擋板密封卡口接頭.全面附加機體配件評估
分享友人
分享到 Line

分享到臉書