板梁腹板接合 的英文怎麼說

中文拼音 [bǎnliángfùbǎnjiēgě]
板梁腹板接合 英文
plate girder web splice
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  • 腹 : 名詞1 （軀乾的一部分） abdomen; belly; stomach 2 （鼎、瓶子等器物的中空而凸出處） empty and protr...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 接合 : joint; zygosis; juncture; articulation; concrescent; nexus; coaptation; syndesis; synapsis; meet;...
  1. Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior

    分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大，實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著，而連接端板厚度及剪力連接程度的影響則不是太顯著。
  2. ( 2 ) based on the existing theory of lateral load distribution rule, and combined the structure characteristic of pre - stressed lager cantilever composite beam with corrugated steel webs, this thesis proposed the modified rigid beam method. taking this method, it is facilitated to compute the lateral load distribution factor of bearing composite cantilever beam with variable - stiffness under the load in arbitrarily position

    （ 2 ）以現有的橫向分佈理論為基礎，結合大懸臂波形鋼腹板組合挑梁的結構特點，提出了修正剛接梁法的計算方法，能夠方便地計算變剛度懸臂組合梁任意點位的橫向分佈系數。
  3. 962m respectively ). neighbouring segments are linked with bolts and welding. after the girders were segmented, guesseted plates were used with high - strength bolted oints to connect the web plates, and the higher and lower flange plates were butt - welded

    相鄰梁段之間的連接形式為栓焊混合型連接，採用節點板把腹板用高強螺栓連接後上、下翼緣板分別對焊。
  4. Shear properties in the plane of the panel ( interlaminar shear ) duplicate the kind of shear stress encountered in such glued structural assemblies as structural sandwiches and adjacent to gluelines between flanges and webs in box - beams and i - beams and gusset plates in trusses

    面板平面的剪切特性（層間剪切） ，與夾層結構這類粘合組件，以及箱形梁、工字梁凸緣與腹板間的焊接層和桁架加固板附近位置所受的剪切應力類型相同。
分享友人
分享到 Line

分享到臉書