板極電壓降 的英文怎麼說

中文拼音 [bǎnjídiànyājiàng]
板極電壓降 英文
anode voltage drop
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 壓 : 壓構詞成分。
  • 降 : 降動詞1. （投降） surrender; capitulate 2. （降伏） subdue; vanquish; tame
  • 電壓 : voltage; electric tension; electric voltage
  1. For saving driver ics ' power consumption and cost, this research proposes a novel display pixel design with integrated charge pump circuits. the proposed display pixel design can supply driving voltage more than double the input voltage to display pixels. there are two advantages for this developed novel pixel design. first, the power consumption of the panels with the proposed novel pixels can be reduced due to the lower voltage on data lines. second, the high voltage driver ics are not necessary, such that the cost and power consumption of the corresponding driving systems can be diminished. from the simulation results, the pixel voltage indeed could raise to more than double input voltage by this proposed design. in addition, the pixels with charge pump circuits also retrench about half power consumption than the conventional display pixels

    為了節省面板電路驅動晶元的功率損耗以及製作成本，本研究提出一種新的像素電路設計，而在設計中將會融合電荷泵電路.利用這種電路設計的像素可有效地將像素電極上的驅動電壓提高到輸入電壓的2 3倍以上.此像素電路設計具有兩個優勢:第一，可以有效降低顯示面板的像素功率損耗;第二，不需高電壓的面板電路驅動晶元，因此可節省晶元的成本及功率損耗.由模擬結果可知，像素電極上的驅動電壓確實可由此像素電路設計而提高到輸入電壓的2 3倍以上;而像素的功率損耗也可有效地降低，約為傳統像素的1 / 2
  2. Based on the simplified principle, the modal shapes of selected structural modes are converted into modal strains. to minimize the calculation error, curve - fitting technique is used in the process. the modal strains are summed together to determine the global distribution of the structure for selected vibration modes so that the position of piezoelectric elements could be optimally determined according to the simplified optimization principle

    通過二階中心差分運算將模態振型轉化為模態應變，採用應變曲線擬合方法降低離散誤差，進而將各階待控模態應變進行疊加，獲取系統整體特徵應變分佈情況；最後根據壓電元件位置優化的簡化目標函數，將壓電片的最優位置確定為柔性板疊加模態應變的極值區域。
  3. Compared with the extension actuation mechanism of piezoelectric materials when electric field and poling direction are along the piezoelectric layer thickness, the shear actuation mechanism of piezoelectric materials when applied electric field and poling direction are perpendicular can induce lower stresses in actuators, which can reduce the possibility of debonding in actuators boundaries

    與外加電場與極化方向平行於板厚度的壓電材料的拉伸作動機制相比，外加電場與極化方向垂直的壓電材料的剪切作動機制可以在作動器內產生較小的應力，從而降低作動器邊界產生分層破壞的危險。
分享友人
分享到 Line

分享到臉書