板筋 的英文怎麼說
中文拼音 [bǎnjīn]
板筋
英文
backstraps /paddywack-
Aseismatic strengthening of reinforced concrete short column with steel plate hoops
鋼筋混凝土短柱利用外包鋼板箍抗震加固的設計To improve the binding strength between the deck slabs and deck surfacing layer of badong changjiang river highway bridge and to provide the surfacing layer with anti - cracking ductility, a series of technical measures has been taken in the construction of the deck surfacing of the bridge, including those of embedding binding reinforcement in the deck slabs, spraying inorganic binding agent between the slabs and layer, replacing part of the cement with micro expansion agent and adding appropriate amount of polypropylene fibers to the concrete
摘要巴東長江公路大橋橋面鋪裝，通過採取預埋橋面粘接鋼筋、噴塗無機界面粘結劑、用微膨脹劑替代部分水泥、在混凝土中摻入適量的聚丙烯纖維等措施來提高橋面板與鋪裝層間的界面粘結強度和給橋面抗裂增韌。The main components of the latter are multi - rib sandwich panels, including floor slabs and wall slabs. reinforced concrete conformation columns are set where the longitudinal walls and latitudinal walls intersect and copulative beams are set where floor slabs and wall slabs intersect. they play a role of linking and transferring loads, bearing a small part of loads at the same time
無骨架體系的主要承重構件是密肋夾芯板（包括樓板和墻板） ，縱、橫墻相交處設鋼筋混凝土構造（連接）柱，墻板和樓板相交處設連系（圈）梁，連系梁和柱主要起連接和傳遞荷載作用，也承擔少部分荷載。He found that the reinforcement in the slab is curtailed.
他已發現板內鋼筋削減。Problems and analyses in designing rc floor slabs
鋼筋混凝土樓板設計中常見的問題及分析Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed
在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。Filler concrete joists for reinforced and prestressed concrete floors
鋼筋混凝土和預應力混凝土地板填充混凝土接縫Some effective measures were presented to solve bigger prestress loss of mid span in overlong frame and it is suggested that prestressed reinforcement with curve linetype should be adopted in slabs if possible
在次梁與板中為有效利用無粘結預應力筋，建議在板厚許可的情況下盡量採用曲線形預應力筋。Technical consultant for manufacture of big span prestressed concrete reiteration plate
4 .大跨度預應力鋼筋砼疊合板生產技術的咨詢。Light steel is the sansei construction, which is adopted got - up h type steel, thin cliff cold blending c, z type steel combination or construction framework, the roof and the wall body are adopted color coat die - mould steel board or sandwich color board, which already replaces the traditional armored concrete build in developed countries
輕鋼結構是第三代建築，它採用製作h型鋼及薄壁冷彎c 、 z型鋼組合或建築骨架，層面和墻體採用彩色塗層壓型鋼板或夾芯彩板，在發達國家已基本取代傳統的鋼筋混凝土建築。Penetration probability of stiffened plate - grid under shock loading
沖擊載荷作用下加筋板架破壞概率分析Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete
通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。There are two pieces of stiffeners and brackets must be replaced
有兩塊加強筋和肘板要換新。This article gives the subsistent ability and the analysis result of intensity after repair in the open field airplane composite material structure by research the intensity, rigid and repair problem under a axis compress loads on a typical three stiffened composite laminate which has a penetrability crack ( a scatter damage ) by a shrapnel
本文通過飛機典型復合材料三加筋層壓板結構在被彈片劃開一穿透性切口（離散源損傷）后，在軸向壓縮載荷作用下所產生的強度、剛度以及修理問題展開了技術研究及探討，給出軍機復合材料加筋板在彈擊後生存力以及外場修理后強度恢復分析結果。This paper referred to the massive domestic and foreign technical material, elaborated in the sheet forming value simulation theory essential technology in detail, points out when analysis sheet forming question should use the big distortion ball plasticity fem and introduce the application characteristic and the function summarizes of the sheet forming simulation software dynaform. secondly, analyzed the cover forming characteristic, simultaneously introduced the influence cover forming factor in detail : such as ramming direction, the craft addendum surface and the material pressing surface, the radius of convex - concave mold, draw bead, pressure strength, blank size and craft margin and so on. and simulates many typical automobiles cover panel with software : such lateral board, back taillight pedestal and storage cover
其次，分析了覆蓋件成形的特點和要求，同時詳細介紹了影響覆蓋件成形的因素如沖壓方向、工藝補充面和壓料面、凸凹模圓角、拉延筋、壓邊力、坯料尺寸和工藝切口等，並用數值模擬軟體對多個典型的汽車覆蓋件汽車后側圍板、后燈座以及轎車后備箱蓋的沖壓成形情況進行模擬，用模擬結果優化拉延工藝方案，比較了內覆蓋件和外覆蓋件在成形特點和要求的一些異同點，以及常見的起皺、拉裂和回彈、成形不足等缺陷的產生機理和相應對策，重點介紹工藝補充面和壓料面的設計及優化方法，因為拉延是沖壓工藝的關鍵工序，而工藝補充面和壓料面的設計是拉延工序的關鍵，對消除缺陷至關重要。In the design, the construction measures such as application of shrinkage - compensating concrete, arrangement of spacing layer between the foundation rock and the bottom slab, adding outside waterproof layer, flexible connection between outlet pipe with side - wall, integerated concrete placement of pump seat with bottom slab and design of reinforcement with application of advanced calculation theory are used according to the characteristics of lager span, larger volume and complex loading conditions of the understructure
針對下部結構跨度大、體積大、受力復雜的特點，在設計中採取多種措施，包括採用補償收縮混凝土、基巖與底板間設隔離層、增設外防水層、出水管與邊墻採用柔性連接、機座與底板整體澆注、採用先進計算理論指導配筋。She was quite mechanical and unthinking in the way she ironed the shirts
她熨襯衣時樣子呆板，不動腦筋Lightweight concrete wallboards - unreinforced
輕質混凝土.無鋼筋墻板The minimum reinforcement rate has little effect on reinforcement in columns. ( b ) when considering the bars in slab participate in beams against negative flexure, four or six times slab - thickness on each side of web can be defined as the effective flange width of slab by intermediate or rare earthquake actions
當考慮板筋對梁端負彎矩承載力的提高作用時，可在設防烈度地震和罕遇地震作用下分別取每一梁側四倍、六倍板厚范圍作為板的有效寬度。It begins with designing two representative reinforced concrete public frames according to new codes in this paper, and carries out nonlinear dynamic analysis by inputting ground motions at the intensity of intermediate earthquake and rare earthquake actions. the slab - bars effect on yield strength of beams is involved in analysis
本文嚴格按照新規范設計了設防烈度分別為7度半、 8度半的兩個民用建築鋼筋混凝土典型框架，然後分別對其進行了設防地震作用和罕遇地震作用下的非線性動力反應分析，並在分析中考慮了板筋作用對梁端屈服彎矩的影響。分享友人