板箱梁 的英文怎麼說
中文拼音 [bǎnxiāngliáng]
板箱梁
英文
slab box beam-
Considering the difference of cantilever plate between the end and the middle of the concrete box bridge, the chief influence factor is studied
考慮箱梁端部和跨中懸臂板根部的區別，研究了影響變厚度懸臂根部彎矩的主要因素。Being aimed to the irrationality and inadaptability of different calculation methods for wide cantilever plate, study of space numeric simulation analysis about concrete box bridge cantilever plate can be carried out for three dimension solids based on ansys
摘要針對混凝土箱梁懸臂板諸多演算法的不合理性，應用大型通用有限元分析軟體ansys ，以三維實體單元對混凝土箱梁懸臂板進行空間數值模擬分析研究。The consequence is, when the majority of structure does n ' t enter yield habitus, but the position of belly - board has been reached the ultimate habitus, it lead to material waste of the other positions, we should pay attention to the disastrous result it will bright to us
它帶來的後果就是當結構的大部分處于彈性狀態時，箱梁腹板處由於剪力滯效應一般最先達到強度極限狀態，導致腹板間材料的抗力沒有得到充分的使用，如不引起重視會帶來災難性後果。In this paper, a high performance sma system applied to steel bridge deck is put forth in allusion to the pavement project of the wuhan junshan yangtze river highway bridge. it comprises steel slab, zn coating layer, closing layer, adhesive, pre - mixed asphalt stone and dual layer sma from bottom to top. it is based on the fea results of the forces and deformation of the pavement layer by means of the algor feas, according to this bridge ' s traffic and the ambient temperature varying range of the pavement layer
本文針對武漢軍山長江公路大橋鋼箱梁橋面鋪裝工程，從鋪裝層環境溫度變化范圍、交通量等使用條件出發，在用algorfeas有限元分析軟體分析鋪裝層受力變形基礎上，提出了（即鋼板+金屬鋅塗層+封閉層+粘接劑+預拌瀝青碎石+雙層sma ）的高性能鋼橋面sma鋪裝體系，並對這種sma的組成材料，包括改性瀝青、集料、礦粉、纖維進行了比較研究，設計了這種sma的配合比，對sma混合料的性能進行了對比試驗，對這種sma方案進行了疲勞性能研究，驗證了所選擇sma方案的可行性。The work in this thesis mainly includes following parts : 1. as for box girder cross section, the three - bar stimulation method under typical loads and supports has been introduced. the force and stress formulae for flanges have been derived from the three - bar method. by reasonable simplification for multi - cell box girder, the three - bar method has been applied in multi - cell box girder ' s shear lag analysis
對于箱形截面主梁，本文介紹了三桿比擬法上、下翼板中比擬桿的計算公式，以及在典型荷載和支承的情況下翼板內各桿的應力計算公式，並對多箱式主梁截面進行合理簡化，使三桿比擬法應用於多室箱梁的剪力滯分析。And the utility skill and the initially drafted three schemes of the sub model in concrete bridge box cantilever plate are analyzed
分析初擬的三種局部精細分析技術實施方案，總結局部精細分析技術在混凝土箱梁懸臂板空間數值模擬中的應用技巧。Also, the thesis calculate and analysis the transverse deflection of steel box girder deeply in multiple factors. firstly, the article introduced the calculative methods and theory of local stress and strain of bridge structure. then program software system of finite element method was introduced. after that, the influential factors to the calculatial result and their values were analysed and suggested
本文首先介紹了橋梁結構局部應力應變計算理論和方法，對有限元計算程序進行了介紹，然後分析了縱橫隔板設置、梁高及梁寬變化等因素對鋼箱梁橋面板在恆載作用下的橫向撓度的影響，並將這些計算結果進行對照分析，從而找出了影響橋面板橫向撓度的主要影響因素，並得出了相應的數值可供工程實踐參考。According to the analysis result, the reason of the inclined cracks in the box girder webs of the bridge is found
根據分析結果，找到了該橋箱梁腹板斜裂縫的成因。Modeling the general solid web continuous box girder and opening - in - web ( open web ) continuous box girder by ansys finite element modeling tool, node stress of governing section and corresponding shear lag values are analyzed. the solution is validated by comparing with variational results and modeling test values. based on the model, the section shear lag induced by dead load, prestress tendons and car loads under the most unfavorable condition and lateral symmetry are also approached. the influence of shear lag effect in double - level continuous box girder is considered with opening - in - web and the web location. the analysis indicates that double - level - load arouses less shear lag effect than one - level - load. when self - weight and prestressed tendons act on together, the shear lag effect on box girder take on a evidently change
基於所建立的有限元模型，本文分別對實腹和腹板開孔兩種箱梁在恆載、車載、預應力荷載作用時，各主要截面的剪力滯效應進行分析，通過施加縱向最不利的和橫向對稱的車輛荷載，研究實腹連續箱梁和空腹連續箱梁在承受雙層荷載和單層荷載時引起的剪力滯效應，並考慮腹板開孔及開孔位置對于連續箱梁剪力滯效應的影響。分析表明，雙層車載對于箱梁引起的剪力滯系數比單層車載的影響要小，對于箱梁中存在引起的剪力滯后現象有一定的改善作用。Based on the research of influenced parameters on constant and varying depth solid web box girder before, the shear lag aroused by the parameters including width - span ratio, outstanding flange on base slab and the position of the tendons are further studied. the investigation show that shear lag values diminish along with the decease of width - span ratio and the departure from the symmetrical axis of anchor position, but outstanding flange is contrary to the former
在前人對等截面、變截面實腹箱梁剪力滯效應影響參數研究的基礎上，本文進一步對腹板開孔的連續箱梁的寬跨比、底板翼緣伸出以及預應力錨固位置改變等參數對箱梁剪力滯的影響進行研究。Due to their simplicity in fabrication and excellent strength to weight ratio, stiffened steel panels are also widely used for construction of land based structures such as box girder and plate girder bridges
由於製作簡單且有良好的強度重量比，加筋板也廣泛應用於製造陸基結構物如箱梁和板梁橋等。The contents include : based on the previous research and the data of experimentations, the author researches and develops a kind of satisfactory semi - empirical formula of nonlinear temperature distribution, and calculates the temperature stress of rigid - framed arch bridge by the fem. the temperature effects of bridge structure by annual and sunlight temperature difference are discussed, it indicates that the temperature effect of annual temperature difference is small but the temperature effect of sunlight temperature difference is great and the temperature stress along beam depth resulted from sunlight temperature difference is nonlinear. with the comparison between the temperature effects of different position of bridge, the results show that where the section of bridge is small, the temperature stress of it is large
本文主要包括以下內容：從理論上研究並結合實測資料發展了一種比較理想的半經驗溫度場非線性分佈公式，並將有限元方法應用於剛架拱橋結構溫度應力的計算中，對橋梁結構進行整體溫度應力分析；討論了年溫差和日照溫差引起的橋梁結構的溫度效應，表明年溫差引起的溫度效應較小，而日照溫差引起的溫度應力較大且沿梁高呈非線性分佈；分析比較了橋梁結構各個部位的溫度效應的大小，可知截面越小溫度拉應力越大，受力越不利；並對箱梁結構由於構造不同引起的縱向與橫向的溫度效應大小進行了探討，發現在頂板下緣也會出現相當大的溫度拉應力，並且梗腋的存在反而增加了頂板底部的溫度拉應力；還對幾種相近的剛構式橋型的溫度效應進行了分析對比，總結了這些橋型針對溫度效應的優劣，並提出相應的針對性措施。Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。Each bundle of strands is connected to one side of the center web of the two cell box girder.
每束鋼纜錨固在雙箱梁的中間腹板的一側。As a result of the complicated analysis of the curved thin - walled box girder, there has little feasible methods to designs the diaphragm ’ s space between
由於曲梁的受力復雜，分析繁瑣，並沒有實際可行的計算方法確定橫隔板的設置間距，在規范中對箱梁沒有明確條文規定。Considering the past research results, frost resistance of concrete using portland cement, and the designed service life of 100 years of testing bridge, the control indexes of high durability concrete are defined in this paper. mixture proportion of concrete used in pier column, coping, precast box beam and plate of bridge is designed based on the compact pile theory, and construction technique is studied also
結合課題組以往的研究成果，根據試驗橋設計使用壽命100年的要求，確定出高耐久性混凝土的設計控制指標，基於最緊密堆積原理和最佳漿骨比原理對橋梁的墩柱、蓋梁、預制箱梁和橋面板用高耐久性混凝土的配合比進行設計，並對其施工應用技術進行了研究。A new kind of theory and calculating method which is suitable to cable supported bridges was developed in this paper. cable element can include the structure ' s geometry nonlinearity and initial stress, virtual laminated element has high calculating efficiency and good precision. dimensions of lsctb was put forward based on conclusions of optimum analysis
推導了適合纜索承重橋梁的纜索單元；引入虛擬單元理論，提出適用於大跨纜索承重橋梁鋼箱梁的一種新方法?虛擬層合板單元法，該單元具有計算效率高，可以模擬復雜結構並滿足工程需要等諸多優越性。The box - girder has many advantages for example light weights and so on. but in practical projects, there are some problems, for instance, the design of diaphragms
但是在實際工程應用中，有許多具體問題需要進一步研究，例如，鋼箱梁的橫隔板的設計問題As for side box girder, the elastic theoretical solution has been introduced. the method is based on stress function and regards side box girder as combine of plate element and shell element. then the force and stress formulae for flanges have been derived
對于邊箱式截面主梁，本文介紹了彈性理論解法，基於翼板單元應力函數，將邊箱梁視為板單元和筒殼單元的組合體，從彈性力學出發，推導出板中法向應力。Discusses of design method of box girder with corrugated steel webs
波形鋼腹板箱梁橋設計方法探討分享友人