校直 的英文怎麼說

中文拼音 [jiàozhí]
校直 英文
align; aline; straighten; alignment; straightening校直機 straightener; 校直器 swage
  • 校 : 校名詞1. （學校） school 2. （校官） field officer3. （姓氏） a surname
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  1. Undesirable magnetic coupling can occur as a result of an error in the alignment of the torquing system.

    力矩系統校直存在的誤差能產生不希望有的磁性耦合。
  2. It is made up of the melting shaft furnace, titled holding furnace, ( reverberatory refining furnace ), casting machine, automatic shearer, cast bar straightening and dege shaving machine, rolling mill, engine oil lubrication system, emulsion lubrication system, rod orbital coiler, line electric control, etc

    銅桿連鑄連軋機生產線主要有融化豎爐，傾動式保溫爐， （銅精煉反射爐） ，連鑄機，滾剪機，校直刨邊機，打毛機，連軋機，潤滑油系統，乳化液系統，銅桿還原冷卻裝置，雙筐梅花收桿機和電氣控制系統等組成。
  3. Laminated leaf springs - alignment clips

    疊板彈簧.校直彈簧夾
  4. 42crmo steel crank possess high proportion in the manufacture of crank. the research as a example of 42crmo steel crank, study feasibility and dependability of jumping measurement overproof alignment technology for crank

    42crmo鋼曲軸在我國曲軸生產中佔有很大的比例，本項研究就是以42crmo鋼曲軸為例，研究曲軸跳動量超差校直工藝的可行性和可靠性。
  5. Crank of internal combustion engine after every process and hot surface treatment will produce fairly deformation, that is jumping overproof. so alignment without destroy for its tissue and property is important factor which ensure operation of crank safely

    內燃機曲軸在各加工工序及表面熱處理后會產生一定的變形即跳動超差，對其組織和性能無破壞的校直是保證曲軸安全運行的重要因素。
  6. The subject for different process technology and surface treatment of crank takes tracking checkout for its internal stress, analyses relation of jumping measurement, deformation measurement, recovery measurement and stress change, finds the reason and usual law of jumping overproof of crank. through cold pressure alignment, hot pressure alignment, support aged alignment and so on methods for 42crmo steel crank, the subject checks change of stress in the process of alignment and change of tissue and property after alignment for crank, and gives comprehensive evaluation for every alignment technology, then give safe and feasible technology parameter

    本課題主要是對不同加工工藝及不同表面處理過程的曲軸，對其內應力進行跟蹤檢測，分析各工藝過程中跳動量、變形量、恢復量與應力改變的關系，找出曲軸跳動量超差的原因和一般規律。通過對42crmo鋼曲軸進行「常溫壓力校直」 、 「熱壓力校直」 、 「支撐時效校直」等方法的校直，檢測校直過程中曲軸應力的變化及校直后組織和性能的改變，進而對各校直工藝進行綜合評價，給出安全可行的工藝參數。
  7. Railway applications - track alignment design parameters - track gauges 1435 mm and wider - plain line

    鐵路設施.軌道校直設計參數.軌距1435mm和更寬.普通線路
  8. Abstract : the mechanical structure of washboard valve leveler is introduced, the alignment mechanics of curving bar and hemilateral pan of the valve is analyzed, the mechanical, the shape of washboard and the effect of alignment quality and efficiency cause by shrink - adaption range of the valve between two washboard are discussed

    文摘:介紹了搓板式氣門校正機的機械結構，分析了氣門桿部彎曲校直和盤部偏歪校正的機理，討論了機器結構，托板形狀和氣門在兩搓板間的過盈配合量對校正質量和效率的影響。
  9. We estimated the weighted mean differences or standardized mean differences, with their 95 % confidence interals, in mechanical axis alignment, duration of surgery, and functional scales between naigated and conentional surgery

    對于導航和傳統術式的力軸校直、手術時間和功能得分，我們計算了加權均數差值或標準均數差值的95 %可行區間。
  10. Aligned grid valve

    柵極中點校直的電子管
  11. Aligned grid tube

    柵極中點校直的電子管
  12. Alignment spring clip

    彈簧校直夾
  13. Pulling 、 straightening 、 bending 、 cutting can be completed in an working cycle

    由開卷、校直、成型、切斷等部分組成，在一個循環內完成。
  14. The application of cartridge valve in transforming the hydraulic system of straightening machine manipulator

    插裝閥在校直機機械手液壓系統改造中的應用
  15. Bushings ( 4 ) : furnishes shaft support at three locations for positive shaft alignment and actuator support

    襯套（ 4 ） ：在三個位置上配置軸支撐，有利於軸校直和執行機構的支撐。
  16. In this paper the design of the structure, hardware and software of this straightening and detecting system of axle is finished

    文中完成車橋校直檢測系統的結構設計、硬體設計和軟體設計。
  17. As they walked in a peaceful park amid blossoming flowers, the colonel spoke frankly of preparations for war.

    當他們在寧靜的公園里的花叢中散步時，那個上校直截了當地說到備戰問題。
  18. Fc approved a new commitment of 376 million for enhancing the administrative computer systems in public sector schools, local schools under the direct subsidy scheme, and ed

    財委會批準開立為數3億7 ， 600萬元的新承擔額，以便改善公營學校直接資助計劃下的本地學校和教育署的行政電腦系統。
  19. Fibre optic interconnecting devices and passive components - basic test and measurement procedures - part 2 - 24 : tests - screen testing of ceramic alignment split sleeve by stress application

    光纖互聯裝置和無源部件.基本試驗和測量步驟.第2 - 24部分:試驗.對陶瓷校直夾板套筒加負荷的篩析試驗
  20. The unit is composed of hydraulic and double conic placing, hydraulic spading and drawing, straightening, shearing, end stopping, coiling, feeding, dropping cart, ect

    本機組有液壓，雙錐放料，液壓鏟頭引頭，送料，校直，剪切，阻尼，收卷，上料，下料小車等主要部件組成
分享友人
分享到 Line

分享到臉書