梁單元 的英文怎麼說

中文拼音 [liángdānyuán]
梁單元 英文
beam element
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  1. When we design the purlin of the metal roof, we made used of the continuous beam mechanic characteristic to find internal force

    工程設計時利用連續梁的分析方法獲得構件的內力，為此構建了一個用梁單元和二力桿單元構成的力學模型。
  2. Based upon virtual displacement method and the updated - lagrangian approach, stiffness matrices for two - dimensional elastic - plastic beam model in large displacement were proposed, in the derivation of which transverse stress was included because it was believed that part of the 2nd order effects of various stresses, which are in equilibrium with each other and with the external loads, will counteract each other and neglecting either part would possibly lead to incorrect results

    利用虛位移原理和更新的拉格朗日方法，導出了大位移彈塑性梁單元剛度矩陣的顯式表達式，在剛度矩陣推導中引入了截面內非線性剪應力和橫向應力的影響，剛度矩陣通過了剛體檢驗。之所以要引入橫向應力的影響，是因為本文認為，保持平衡所需的所有應力，它們各自的二階效應會相互抵消，因此忽略其中的任何一項都可能導致不正確的結果。
  3. In this paper, the practical model for calculation torsion is set up in algor feas, which is 3 - d girder element model with rigid arms. the model is better used to calculate the effect of deviation load

    本文在algorfeas中建立了一種計及扭轉的實用模型?帶剛臂的三維梁單元模型，用此模型能較好地計及荷載偏載效應。
  4. Error : element 16 is close to parallel with its beam section axis

    使用梁單元出現如下錯誤，是什麼原因？ ？
  5. The static analysis of the long span plate - truss composite cable - stayed bridges. first, the cr formation on the geometric non - linear structural analysis is introduced. next, the structural discretization of cable - stayed bridge, the stiffness matrix the formation of nodal force and the simulated construction system are introduced

    首先介紹了本文採用的桿系結構幾何非線性問題的分析方法? cr列式法，其次介紹了板桁結合斜拉橋的結構離散及桿單元、梁單元的剛度矩陣以及節點力的形成方法，然後介紹了斜拉橋施工模擬體系的形成。
  6. From the feature of the force and deformation of the tpih, 5 different elements are used to mesh the different zones of the tube, which are structural beam 3d elastic 4, structural pipe plastic straight 20, structural pipe elastic elbow 18, structural shell elastic 4 node 63 and contact 3d pt - to - surf 49 ; the contact problem is assumed to be flexible - to - flexible ; the temperature field is assumed to be body load. a mechanical model corresponding to reality has been established for numerical simulation. based on the above, the 3 - d fem numerical simulation of tpih has been carried out by using the ansys program

    針對加熱彎管過程的受力和變形特點，採用三維梁單元、三維塑性直管單元、三維彈性曲管單元、三維殼單元與三維點對面接觸單元等5種不同的單元分別對管毛坯不同區域進行劃分，並對接觸單元採用柔體-柔體的處理方法，將溫度場作為體載荷處理，建立了符合實際的加熱彎管問題數值模擬力學模型：在此基礎上，應用商用軟體ansys對加熱彎管過程進行三維有限元模擬與研究，獲得了成形時推力、彎矩、支撐力大小及其變化趨勢。
  7. Based on the force - method equation, the stiffness matrix and fixed - end nodal displacement and force vector are derived

    在力法方程的基礎上，給出了組合梁單元的剛度矩陣、桿端位移向量及桿端荷載向量並建立了剛度方程。
  8. A force - method equation about unknown nodal forces of the composite beams is proposed based on the governing differential equation

    在粘結剪力和滑移微分控制方程的基礎上，建立了關于組合梁單元桿端未知力的力法方程。
  9. Secondly the author ' s study are introduced in this paper. the author study mainly the linear static and dynamic, elastic - plastic static and dynamic problems of cfst arc - bridge. firstly, the author establish the linear static equation on the based of the rigid equation of element by qr - method, and then analysis the inner force of arc bridge, establish the linear dynamic equation and elastic - plastic rigid equation and dynamic equation, then solve respectively the elastic - plastic rigid and dynamic equation by the method of repeated increment and no limit stabilization, arithmetic

    本文主要研究大跨度鋼管混凝土桁架拱線性靜力問題和線性動力問題以及彈塑性靜力問題和彈塑性動力問題，先利用qr法按照梁單元的剛度方程建立桁架拱的線性靜力方程，進行桁架拱內力分析，建立桁架拱線性動力方程、彈塑性剛度方程及彈塑性動力方程，然後利用增量迭代法及樣條無條件穩定演算法分別求解彈塑性剛度方程及動力方程。
  10. An efficient finite element of spatial curved beams

    高效的三維曲梁單元
  11. Micro beam model for 3d woven composite materials

    三維機織復合材料的一種梁單元細觀力學模型
  12. The method of spatial curved girder element in this paper offer reference for analysis of curved girder bridge, so it is significative to actual structural and lay a foundation for further development of curved girder structural analysis program

    本文提出的空間曲梁單元的實用計算方法，為彎梁橋的空間分析提供了參考，具有工程實際意義，也為進一步完善彎梁橋結構分析程序奠定了基礎。
  13. Also the modeling of the super - length tall buildings is provided. the whole structure of super - length tall buildings is chosen as an object of study, and a worldwide used large - scale structural analyzing program named super sap93 is also chosen to decentralize the structure into elements. the beams and columns of the structure are modeled as dimensional beam components, and the floor slabs and sheer walls are modeled as dimensional slab components

    本文以超長高層建築整體結構為研究對象，採用國際通用的大型結構分析程序supersap93對超長高層建築結構進行有限元離散，結構的梁和柱採用空間梁單元模型，樓板和剪力墻以及筒體結構採用空間板單元模型，建立實用的超長高層建築結構整體結構分析模型。
  14. On the basis of large - displacement virtual principle, the finite element equations of stable type suspension bridge containing towers are driven. the stiffness matrixes of the cable element, the bar element and the beam element using node coordinates are given, too. such method has not been found in reference books

    論文從有限位移彈性理論的虛功方程出發，推導出穩定橋全橋結構的非線性有限元運動方程，還推導了用節點坐標表示的索單元、桿單元和梁單元的單元剛度矩陣，這一點在參考文獻較少見。
  15. Based on the structural feature of long blade with friction damper, pretwist beam element and space straight beam element were adopted to discrete the blade, and the numerical model of damper link element was established, then the gross finite element motion equation of the blade was obtained

    針對帶摩擦阻尼器長葉片的結構特點，採用扭曲梁與空間直梁單元模化葉片，推導葉片阻尼連接單元的力學模型，由此建立葉片總的動力特性分析方程。
  16. Instead of the conventional node - node model, the spot - weld is modeled by a new short beam element introduced into between node and clement, which is subject to the tensile and shear forces

    新型焊接單元在有限元節點與單元之間引入短梁單元來模擬焊接關系，單元承受拉伸力和剪切力。
  17. Three circumstances on the geometric non - linear analysis are considered : the sag phenomenon of cables the nonlinear behavior of bending members and the geometry change due to large displacement. the non - linear behavior of cables is verified by introduced the ernst cable modulus of elasticity and cr formation is applied to analyze the non - linear of beams. an incremental - iterative method based on the newton - raphson method is adopted here to solve the non - behavior equations

    幾何非線性分析主要考慮三個方面：索的垂度效應、樑柱效應和結構大位移，其中：索的非線性分析採用ernst彈性模量對索材料的彈性模量進行修正，計及索的垂度效應的方法；梁單元的非線性分析採用cr列式法，計算中採用基於newton - raphson法的增量迭代方法求解非線性方程組。
  18. The tapered beam element is used hi the fem. with the fem. the linear static and in - plane stability analysis of the frames are carried out conveniently

    本文開發了一套變截面梁單元有限元分析程序，可對變截面門式剛架結構體系進行精確的靜力計算與平面內穩定性分析。
  19. A new nonlinear finite element model which applies subsystem connect beams element and space degenerate shell element to analyze eccentric braced structural energy - dissipation and links collapse mechanism is presented in this paper

    本文提出了應用子結構法聯合梁單元與空間退化曲殼單元分析偏心支撐鋼框架耗能性能及耗能梁段破壞機理的非線性有限元分析模型。
  20. In the analysis, a cfst arch ( single tube ) is first divided into a finite number of straight beam elements. according to the virtual work principle and the modified newton - raphson iteration method the tangent stiffness matrix considering double nonlinear properties is established. with regard to the non - equilibrium forces, the material nonlinear property along the height of the section and the length of the element is considered and the computation accuracy is improved as a result

    本文首先將拱肋劃分為一系列的直梁單元，運用虛功原理和修正newton - raphan數值迭代演算法的基本原理準確推導了拱肋直梁單元的非線性切線剛度矩陣；在不平衡力方面考慮了沿截面高度和單元長度方向材料非線性的發展過程，提高了計算精度；再根據得到的切線剛度矩陣採用荷載增量步內修正newton - raphan迭代的增量迭代法進行了求解。
分享友人
分享到 Line

分享到臉書