條形缺陷 的英文怎麼說

中文拼音 [tiáoxíngquēxiàn]
條形缺陷 英文
stripy flaw
  • 條 : Ⅰ名詞1 （細長的樹枝） twig 2 （條子） slip; strip 3 （分項目的） item; article 4 （層次; 秩序; 條...
  • 缺 : Ⅰ動詞1 （缺乏; 短少） be short of; lack 2 （殘缺） be missing; be incomplete 3 （該到而未到） be ...
  • 陷 : Ⅰ名詞1 （陷阱） pitfall; trap2 （缺點） defect; deficiency Ⅱ動詞1 （掉進） get stuck or bogged do...
  • 缺陷 : defect; fault; faultiness; vitium; lesion; flaw; disorder; imperfection; drawback; blemish
  1. In the paper, the finite element simulation software dynafrom is applied to analyze the affect of different blank holder during the forming process of laminose stepped tubular part, predict the possible defects such as wrinkle and break, obtain the rational style of blank holder avoiding the occur of defects and determine the rational configuration of die. the forming affect of thin - wall shallow stepped tubular part is analyzed when using different lubricate condition ( friction coefficient ). by this method, the relationship between friction coefficient and drawing depth of laminose stepped tubular part is obtained

    本文利用有限元模擬軟體dynafrom分析了不同類型的壓邊圈對薄壁階梯筒形件成形過程的影響規律，預測了採用不同類型壓邊圈時可能出現的成形缺陷如起皺和拉裂，獲得了防止缺陷產生的合理壓邊圈形式，確定了合理的模具結構形式；分析了不同的潤滑條件（摩擦系數）對薄板階梯筒形件成形的影響，獲得摩擦系數與薄板階梯筒形件的拉深深度的關系；分析了階梯筒形件成形過程中的不同階段的應力應變分佈、毛坯材料厚度變化情況，並獲得了階梯階梯筒形件能一次拉深成形的條件。
  2. Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process

    在相同的注射條件下，通過分析喂料在不同直徑和長度流道中的流動規律，得到了喂料在流道中的速度場、壓力場和溫度場，找到了流道長徑比的合理取值范圍，並得出通過改變流道設計可實現對現有設備資源充分利用的結論；給出了不同注射壓力下，型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線，得到了注射壓力對充填時間和型腔壓力的影響規律，確定了最佳的充模時間、注射時間和注射壓力；通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈，預測了注射件的成形質量，或可能產生的注射缺陷及位置，優化了澆口設置。
  3. The necessary condition has been obtained on forming rolling workpiece surface defect by means of upper - bound method and least energy principle

    以此為基礎，並藉助于上限原理和最小能量原理，獲得了楔橫軋成形階梯軸時軋件表面缺陷形成的必要條件。
  4. Drawing piece unfold size is one basic condition under the calculation on coefficient, number of drawing, handbooks or books of press are not given, practice press production, die designer designs drawing die by experience calculation, after testing, according to deformation, state, defect shape of testing blank, shape and unfold size is revising, finally, unfold size and shape of blank are determined, designing period is longer, cost of die and work piece is to raise, economic benefit is to reduce

    拉深件展開尺寸是拉深可行性分析中計算拉深系數與拉深次數的前提條件，現有沖壓手冊或教材對于復雜拉深件的展開尺寸計算尚未論述。復雜拉深件的沖壓生產中，模具設計者憑經驗估計拉深可行性，設計製造拉深模進行反復試壓，根據試壓件的形變狀態，缺陷形貌，制定坯料展開尺寸和形狀，周期較長，因而生產成本高，經濟效益不佳。
  5. According to the situation request, we combine with the fact on the railway for the time being, raised the whole views and suggestions to the railway improvement, the first : to realise railway shareholding entreprises is the basic way of railway improvement winder the public ownership circumstance, the second : it is gotton the whole locatim to the function of ministery of rail ways, railway bureau. the branch of railway bureau and the units of railway department, it is designed the whole developing frame that the funtion of ministry of railways is macro - controler, the railway bureau or its branch is management substance which ouur legal qualifaction the unit of railway department is the basic product unit, the third : it describes kinds of faults on the present four level management, and tolal the data auording to the fact

    根據形勢要求，結合目前鐵路的實際情況，對當今鐵路的改革提出了整體的看法和建議：第一、實現鐵路企業股份制是公有制條件下鐵路改革的根本出路；第二、對鐵道部、鐵路局、鐵路分局、基層站段的功能給予了整體的定位；設計了鐵道部的功能是宏觀調控者，鐵路局或分局為法人代表的經營實體，基礎站段為生產基本單位的整體改革框架；第三、對目前四級管理體制的種種缺陷作了描述，並根據實際情況進行了數據統計。
  6. This article reviews the developments of studies in inorganic synthesis and preparative chemistry in vital aspects such as the extreme condition synthesis, soft chemistry, the preparation of specially condensed and aggregated materials, morphology and size modifying growth, defect and valence controlling, combinatorial chemistry, computer - aid design, ideal and biomimetic syntheses

    摘要本文從極端條件合成、軟化學合成、特殊凝聚態和聚集態制備、形貌與尺寸修飾、缺陷與價態控制、組合化學合成、計算機輔助合成、理想合成與生物模擬合成等幾個側面，闡述近年來無機合成與制備化學研究的進展。
  7. By increasing the h2 dilution ratio, it is found that atomic hydrogen can selectively etch amorphous phase and stabilize crystalline phase. from the study on the distance from substrate to catalyzer, choosing a proper distance can ensure the gas fully decomposed, while a relatively low substrate temperature can cause the nanocrystalline particles to lose mobility and keep their sizes. the pre - carbonization process can enhance the nucleation density and make the growth of high quality nanocrystalline p - sic films much easier

    實驗結果表明：隨著工作氣壓的減小，薄膜的晶粒尺寸有所減小；通過提高氫氣稀釋度，利用原子氫在成膜過程中起的刻蝕作用，可以穩定結晶相併去除雜相；選擇適當的熱絲距離能保證反應氣體充分分解，又使襯底具有較高的過冷度，是形成納米薄膜的重要條件；採用分步碳化法可以提高形核密度，有利於獲得高質量的納米- sic薄膜；襯底施加負偏壓可以明顯提高襯底表面的基團的活性，因負偏壓產生的離子轟擊還能造成高的表面缺陷密度，形成更多的形核位置。
  8. Based on the analysis about the test requirements and the saturated magnetization of the armor plate, the excitation magnetic circuit satisfying the testing condition and a validation system are designed. because the geometric, of the magnetic leakage at the direction of the normal of the roundness fault has the feature of two peaks : a positive and a negative, using the linear regression and the software matlab, two regression equation are proposed : one is about the peak value of the magnetic leakage and the diameter and depth of the roundness fault ; the other is the distance between the two peaks and the diameter of the roundness fault. the result of the validation system proves that the two equations are valid, and an applied method using for quantificationally inspecting the roundness faults is proposed according to the two equations

    根據實驗要求，通過對鋼板達到飽和磁化的必要性進行的分析，設計了符合試驗條件的勵磁磁路，並設計了一套實驗驗證系統；根據圓形缺陷法線分量漏磁場幾何圖形正負雙峰值的特點，採用線性回歸擬合的原理和matlab軟體及其統計工具箱中的相關函數，給出了圓形缺陷漏磁場幾何圖形的峰峰值與圓形缺陷的直徑和深度以及峰峰值間距與圓形缺陷直徑的兩個回歸擬合方程，並通過實驗驗證系統驗證了擬合方程的正確性，利用這兩個簡單實用的擬合方程，提出了一種工程定量檢測圓形缺陷的應用方案。
  9. Through researching on the classification and form mechanism of loess pitfall, some methods treating the pitfall in collapsibility loess roadbed such as grouting, geocell, explosion, dynamic consolidation and sddc etc. are put forward and the suitable terms of various kinds of methods and their own pluses and minuses have been discussed

    通過對黃土陷穴的分類、形成機理進行分析研究，提出了灌漿法、土工格室、爆破法、強夯法、 sddc法等幾種濕陷性黃土路基陷穴處理的方法，並分析了各種方法的適用條件和各自的優缺點。
  10. Via this model, automatic identification of circuit and circuit defect of s - sbc are realized. the procedures to check for the existence of a crank in all types of s - sbm are found. the method of stationary configuration loop to solve the order of motion of s - sbm is presented

    基於此模型，實現了s - sbc迴路及迴路缺陷的自動識別，給出並證明了所有類型的s - sbm的曲柄存在條件及判斷方法；提出了解決s - sbm運動順序問題的靜止位形點環路法。
  11. It is shown that there are different degree defects in a few definitions in the theories field. in overview of the general requests for giving a definition and the character of the offense of insurance fraud, the writer views that the offense of insurance fraud refers to the act of policy holder, the insured and beneficiary in the insurance contract relation violating the regulations of insurance law to illegally occupy as its purpose, adopt deliberately falsifying the subject matter of the insurance ; or cooking up the cause of an insured accident or overstating the extent of loss ; or inventing stories an insured accident that does not occur ; or deliberately causing the occurrence an insured accident that leads to property ; or deliberately making insurance accidents to swindle large sums of insurance. it has the characteristics as follows : their being subjectively in the diversity of the criminals, the combination of intelligence and cruelty of the criminals, simpler in criminal suspect ; their being objectively in deceptive, crime means " profession to turn, the crime activity concealment very strong, be involved amount of money huge, usually living with other crime companions, the severity of the consequences of the crime, higher black number of crime, and having a thing

    筆者認為:保險詐騙罪的犯罪客體不屬于本罪的構成要件，保險詐騙罪的成立僅須具備犯罪主體要件、犯罪主觀要件和犯罪客觀要件三個要件即可;鑒于保險詐騙罪的預備形態在現實中的危害性不大，本文僅就保險詐騙罪的未遂形態和中止形態進行了探討;著重探討了保險詐騙罪共犯中的身份問題，對保險詐騙罪的教唆犯和幫助犯的構成特徵及刑事責任進行了探討;逐一對保險詐騙罪的實質一罪（法規競合與想像競合）和處罰一罪（牽連犯與吸收犯）進行了分析;同時，從犯罪數額和主觀目的上討論了保險詐騙罪的成罪條件，將保險詐騙罪與普通詐騙罪和合同詐騙罪進行了區分;最後，在對保險詐騙罪立法沿革和立法模式分析的基礎上，從保險詐騙罪的主體、主觀方面、客觀方面以及立法技術等幾個方面對保險詐騙罪的缺陷及其完善提出了自己的看法。
  12. For the substrate of heavily boron doped wafer, it has been proved that oxygen concentration is increased and oxygen precipitation is enhanced by hb ( heavily boron - doping ) during crystal growth, which is beneficial for ig and therefore improve the yield of ulsi

    另一方面，在相同的晶體生長條件下，重摻硼硅單晶氧含量升高，氧沉澱被增強，能形成有效吸雜點，提高矽片機械強度，抑制void缺陷，有利於提高ulsi的成品率。
  13. The buckling and ultimate strength of ship plating normally depend on a variety of influential factors, namely geometric / material properties, loading characteristics, initial imperfections ( i. e. initial deflections and residual stresses ), boundary conditions and corrosion, fatigue cracking

    船體板的屈曲和極限強度取決于很多影響因素，主要有：板的幾何尺寸、材料特性、載荷特徵、初始缺陷（如初始變形和焊接殘余應力） 、邊界條件以及腐蝕的影響、疲勞裂紋等。
  14. Knowing in advance metal flowing process in the forming process, forecasting the critical condition of failure producing and adopting some measures tooptimize process project and process parameter, may avert failure and satisfy the purpose of assuring product quality and enhencing economical benefit

    事先了解金屬在成形過程時的流動情況，預測缺陷產生的臨界條件，採用一定的措施優化工藝方案及工藝參數，可避免缺陷，達到保證產品質量，提高經濟效益的目的。
  15. It was found that the defects were formed and the conductivity increased with the addition of co, which improved the diffusion of proton and inhabited the formation of y - niooh. the electrochemical capacity of the electrode with cobalt additives changed slightly after 206 cycles. the electrode can exhibit excellent high - rate discharge performance, the capacity discharged at 6c ( 1800ma / g ) can reach to 77. 7 % of which discharged at 1c condition

    在納米ni （ oh ） _ 2電極中加入鈷和鋅添加劑，並全面地分析了它們對電極性能的影響，發現加入鈷添加劑后增強了電極的導電性，形成雜質缺陷，更有利於質子的出入，同時抑制- niooh的形成，提高充放電效率和循環穩定性，電極在經過206個循環后變化甚小；電極的倍率放電性能相當出色，在1800ma g （ 6c ）的大電流放電條件下，依然能放出1c的77 . 7 ；在鈷的添加方式中，以co和coo混合添加的效果最佳。
  16. It is necessary to define a numerical expression of the defects in quantitative measure of the quality of part

    兩種方法的結合，必須對板材的成形缺陷進行量化的表示，以形成目標函數和約束條件。
  17. Numerical solution is mainly applied for this problem. adopting certain assumptions, this paper presents an approximate method of obtaining the temperature field by green ' s function, and gives the solution of a two - dimensional field involving a circular vacant flaw

    通常採用數值計算，本文通過採用一定的假設條件，提出了溫度場解析求解的近似方法，並對含有二維圓形空腔缺陷的試件溫度場進行了求解。
  18. ( 4 ) which deformation behavior of cementite lamellae in pearlite colonies is closely related to the stress state of cementite which significantly depends on cementite thickness and orientation, especially on cementite thickness. ( 5 ) the lamellar cementite undergoes partial dissolution on the present deformation. the thermodynamical destability of cementite is attributed to a large number of defect in cementite introduced by severe plastic deformation providing evidence for cementite dissolution

    而滲碳體的應力狀態主要是與滲碳體的片層厚度和取向密切相關的，其中滲碳體的厚度起決定性作用； （ 5 ）本實驗變形條件下，滲碳體出現了部分溶解的現象，這是由於強烈塑性變形而在滲碳體中引入大量的缺陷導致其處于高能不穩定狀態從而促使了滲碳體溶解。
  19. The implementing regulations of the patent law of the p. r. c. stipulates that the invention in the patent law means any new technical solution relating to a product, a process or improvement thereof

    初步審查是指對專利申請是否符合專利法及其實施細則規定的形式要求以及明顯的實質性缺陷進行審查。實質審查主要是對專利申請是否符合授予專利權的實質性條件所進行的審查。
分享友人
分享到 Line

分享到臉書