楔形模 的英文怎麼說

The velocity field has been designed in this article on defect of rolling workpiece surface about cross wedge rolling technique in the process of forming axial symmetry spare parts by result of simulated experiment of consult document [ 4 ]

摘要依據文獻[ 4 ]的模擬實驗結果，擬定了楔橫軋工藝成形階梯軸類件時軋件表面出現表面缺陷（蛇皮狀或魚鱗狀缺陷）時的金屬流動速度場。

With the use of finite method we have developed computer simulation software for vacuum microtriodes with wedge - shaped and cone - shaped cathode on the basis of stduying deeply the field emission theory of vacuum microelectronics. the software included field section, grid point numbering, and the calculation of electric currents, transconductance and cathode capacitance, moreover, it can simulate the properties of vacuum microeletronic with variant structures and sizes. the relationship was studied and simulated among electic properties and device structures, sizes and cathode materials etc. the optimized design of vacuum microtiode was proposed

本文在深入研究真空微電子器件場致發射理論的基礎上，根據圓錐形、楔形陰極真空微電子三極體的不同特點，分別建立了物理和數學模型，在考慮空間電荷密度影響的前提下，以有限元法為基礎採用迭代的方法計算出真空微電子三極體內的電勢分佈情況，繪制出了等勢線、電子軌跡線，並得到了器件電學性能隨幾何參數的變化情況。

An experiment instrument of horizontal evaporation cooling motor with the same dimension such the calculation model is designed and established

為了驗證計算結果，設計並建立了與計算模型尺寸相同的臥式蒸發冷卻電機楔形氣隙旋轉實驗裝置。

Under the assumption that the inner surface of stator sleeve and outer surface of rotor are smooth, taking the fact into account that the temperature of stator sleeve of evaporation cooling motor keeps almost the same, horizontal evaporation cooling motor is simplified as a physical model of two coaxial sleeves, with outer sleeve ( the stator ) holds still and keep at constant temperature and inner sleeve ( the rotor ) is rotating and heated

本文通過數值和實驗手段研究了臥式蒸發冷卻電機楔形氣隙中的流體流動、傳熱現象。本文在定子套筒和轉子表面光滑的假設下，針對蒸發冷卻電機定子套筒壁面基本恆溫的特點，將實際蒸發冷卻電機簡化為同軸套筒內筒加熱旋轉、外簡靜止定溫的物理模型。

Circular wedge fuzzy comlex numbers and their operations

圓楔形模糊復數及其運算

The occurrence probability and existence form of internal defects in rolled pieces during three - roll and two - roll cross wedge rolling were compared and analyzed by finite element numerical simulation

摘要採用有限元數值模擬方法，比較分析了三輥楔橫軋與兩輥楔橫軋軋件內部缺陷的產生幾率和存在形式。

According to the geological survey on no. 316 national road from zaoyang to shuhe in the southern shaanxi province, five deformation and failure patterns of the slope in soft metamorphic rock are concluded and analyzed in detail, for effective forecast and economical treatment of slope hazard

本文通過對陜南316國道早陽蜀河段的實地調查，歸納了該路段軟弱變質巖邊坡的變形破壞特徵，總結出順層滑動、彎曲傾倒、楔形體滑動、潰曲破壞以及滑移拉裂5種典型的病害模式，並對每種變形破壞模式進行了具體的實例分析，從而為邊坡成災預警和選擇經濟有效的治理對策奠定基礎。

Secondly, the finite - element analysis on the typical slope section is performed with establishment of geology model, definition of boundary condition and proper selection of mechanical parameters. the result shows that the slope is of integral stability, and the failure mode mainly comprises infrequent block drop and wedge body breakage. considering the two failure modes of plane failure and wedge body breakage, and stability calculation under different work conditions, the slope stability is discussed and the sensibility ana lysis on its fraction angel and cohesion force is made

然後通過建立地質模型、確定邊界條件、選擇合理的力學參數，取典型斷面對邊坡進行數值分析，分析結果表明斜坡整體是穩定的，破壞類型以零星掉塊和楔體失穩下滑為主；為了定量計算邊坡的穩定性，對邊坡兩種破壞類型：單滑面下滑和雙滑面楔形體下滑，考慮不同工況進行穩定性計算，並對摩擦角和粘聚力進行穩定的敏感性分析。

Firstly, the comparation study between the wedge pressing and the contour forging has shown that the transverse deforming initiated from the surface of the preforms. when the superficies reached the moulding wall, the deforming moved downwards as the high - direction deforming increased, till the moulding chamber was full of stock ; the transverse deforming of the moulding pressing stock initiated from the center of the stock then surned into a drum - type. the distribution of the density and hardness of the high - direction indicated that the wedge pressing acquired a better ability of pressing penetration

首先對比研究了楔形壓制工藝與模壓緻密化工藝，發現楔壓坯料的橫向變形從上表層開始，當上表面與模壁接觸后，隨著高向變形量的增加逐步向下移動，直至坯料充滿模腔;模壓坯料的橫向變形從坯料中間開始，形成鼓形。高向的密度、硬度分佈表明楔壓比模壓具有更好的壓透能力。

Set up the following 2d parametric models : ( dinitial contour of cone. ( 2 ) six types of inserts : cut insert, conical insert, ovoid insert, chisel insert, gage insert and scoop chisel insert. ( 3 ) twelve types of slots : six slots between the rows of inserts ; six slots on the head of cone

建立了以下幾種二維參數化模型： （ 1 ）牙輪初始輪廓； （ 2 ）六種牙齒，包括平頂齒、錐形齒、球形齒、楔形齒、邊楔齒和勺形齒； （ 3 ）十二種齒槽，其中六種牙輪齒圈之間的齒槽、六種牙輪頂端的齒槽。

With this axial symmetric quasi - 3d model, the gas - flow field in such a wedge - shape air - gap is studied, the phenomena about taylor vortex in such a narrow wedge - shape air - gap is illuminated and the so caused gas - flow in axial direction is explained

採用準三維軸對稱的計算模型，對楔形氣隙的流場進行了研究，驗證了高速旋轉情況下，環形間隙流場中充滿taylor渦流的現象及相關規律。

Abstract : the new technology of cross wedge rolling has been using in production of blank forming of oil ejector body

文摘:介紹了一種楔橫軋制坯?精密模鍛成形噴油器殼體毛坯的新工藝，及楔橫軋模具設計工藝參數的選取。

A solid - waste containment system can be simplified as a slope which contains a layer of geomembrane ( which is simplified as interlayer slope in the rest part ). shaking table model test and numerical analysis have been done to study the seismic stability of interlayer slope based on the two - part wedge theory in this paper. many factors which affect the slope stability ratio, including horizontal seismic coefficient, slope angle, soil - geomembrane interaction coefficient, slope length, layer thickness and soil character, have been took into consideration

填埋場防滲基坑的邊坡可以簡化成含土工膜夾層的土坡（以下簡稱夾層土坡） ，本文根據「雙滑楔體」理論思想，對夾層土坡的地震穩定性問題進行了較為系統的模型試驗和數值分析，著重考慮了水平地震系數、夾層土坡坡角、土工膜與覆蓋層土體摩擦系數、夾層邊坡長度和厚度、夾層土坡覆蓋層土體性質等因素對土坡安全系數的影響，並對地震作用下夾層土坡的永久變形進行了初步的研究，給出了對實際工程設計有參考價值的結論。

Results the occlusion contact data and graph of wedge - shaped teeth defect had the features of trauma occlusion. 42. 97 % of them has the larger axial gradient degree, 96. 09 % of them has abration in different classes, 46. 29 % missing the front teeth and 57. 03 % missing the buccal teeth

方法採用臨床物理檢查和石膏模型測量，確定楔狀缺損牙軸傾度、磨損指數、牙缺失等指標；採用計算機圖像處理技術，自行編制軟體程式及硬體系統，測試被檢光（牙合）片，分析並提取楔狀缺損牙接觸（牙合）力、面積、接觸點（牙合）應力等資料和圖形信息。

The cubic law which describe the law of fluid flow in fracture is based on parallel plate joint model, in this paper the cubic law is modified and non - parallel wedge - shaped joint fluid flow equation is formed, coupling relation between seepage and stress is given based on permeability and joint distortion as the linkage between two field, while the coupling mechanism is simple and explicit

描述裂隙水流運動規律的立方定律是建立在平行板裂隙模型基礎上得出的，本文對立方定律進行了修正，推導了非平行楔形裂隙水流方程，根據滲透性和裂隙面變形關系給出了單裂隙滲流與應力耦合公式，耦合的機理十分簡單、明確。

The analytical result of the tir mirror shows that this type of awg device with tir mirrors has high fabrication tolerance. the tapered waveguide and the output waveguide of the device are designed and improved. simulation results indicate that introduction of tapered waveguides with different widths and design improvement of the output waveguide can both improve the performance of the awg device

對全內反射鏡的分析表明這種全內反射型的awg器件具有較高的製作容差；改進設計了awg器件中的楔形波導和輸出波導，模擬結果表明不等寬楔形波導的引入可以改善awg器件的性能，對輸出波導進行改進設計同樣可以提高awg器件的性能。

For shutters, the results show : 1 ) according to the formula p =, the theoretical value of is calculated by the effective velocity of the flow, and its engineering value is calculated by the arriving velocity of the flow, the relationship between the theoretical value of and its engineering value is 2 ) the smaller value of declining angle will result in the smaller pressure loss and smaller outlet velocities. as a result, the declining angle of 30 擄 or less is recommended in some places which need small wind velocity, such as broadcasting studio and library, and the declining angle of 45 擄 or less is recommended in places which need big wind velocity, such as cinema and office ; 3 ) the larger value of ratio between the wide of the shutter b and the space between two boards h ( b / h ) will result in the larger pressure loss and smaller outlet velocities. the range of b / h from 0. 8 to 2. 0 and the optimum value 1. 2 is recommended ; 4 ) the range of b from 10 mm to 50 nun and the optimum value 40 mm is recommended ; 5 ) the proper thickness of the boards 8 of the shutters is 1. 5 mm ; 6 ) cuneiform boards should replace the rectangle inlet boards of the shutters in order to obtain better ventilation

數值模擬採用fluent軟體，計算結果用excel進行處理，通過對大量數值工況進行數值模擬計算，結果表明：對于單側百葉風口，計算表明： 1 ）對于公式p = （ ~ 2 ） 2 ，的理論計算值中定義為流體流經百葉風口內部時的速度，即有效速度，而工程上常使用流體的來流速度來計算，計算表明，的理論計算值與工程應用值的關系為（ _ （理論） ） （ _ （工程） ） = 0 . 813 ； 2 ）當來流速度一定時，擋板傾斜角度越小，壓力損失越小、出口速度越小；因此在要求進口風速比較小的場所，如播音室、圖書館等，宜採用擋板角度30的百葉風口；在要求進口風速比較大的場所，如電影院、辦公室等，百葉擋板的角度應選45 ； 3 ）當來流速度一定時，百葉擋板的擋板寬度b與擋板間距h的比值b h越大，壓力損失越大，出口速度越小，計算表明，鑒于壓力損失、出口風速、板間形成渦流區的大小，百葉擋板的b h值取0 . 8到2 . 0之間， b h = 1 . 2為最佳值； 4 ）當來流速度一定時，在計算的條件下，當百葉擋板寬度b = 40mm時，百葉擋板的阻力系數最小，考慮到渦流區等的影響，建議選用10mm b 50mm的百葉擋板；西安建築科技大學碩士學位論文5 ）百葉擋板的厚度取為1 . sinln為好; 6 ）百葉擋板的入口側可選用具有傾斜度的楔形擋板來代替矩形擋板，利用其較好的導流作用，可得到更好的出流效果。

In the other method, young ' s modulus, residual stress, and bending strength are characterized under a wedge tip by means of micro bridge deflection tests

利用楔形壓頭和薄膜微橋撓曲法，得到了標準氮化硅、低應力氮化硅和氮化鋁薄膜的楊氏模量、殘余應力和彎曲強度。

The theoretical model on reinforced earth retaining wall was given. 5. a lateral displacement analysis model about reinforced earth retaining wall that treats the wall ' s face panel as an elastic foundation beam has been presented

在楔體破壞的基礎上，探討了加筋土支擋結構的側向土壓力分佈規律，建立了一種加筋土支擋結構側向變形分析的理論模型。

Wedged mechanism of die

沖模的楔形機構