極限斷裂荷載 的英文怎麼說
中文拼音 [jíxiànduànlièhézǎi]
極限斷裂荷載
英文
ultimate breading load- 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
- 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
- 斷 : Ⅰ動詞1 （分成段） break; snap 2 （斷絕;隔斷） break off; cut off; stop 3 （戒除） give up; abstai...
- 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
- 荷 : 荷名詞（蓮） lotus
- 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
- 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
- 斷裂 : break; disrupt; flying off; fracture; fragmentation; out break; rift;crack;bursting;rupture;rendi...
-
Here we obtain the strain compatibility method ande equilibrium of forces and concepts of fracture mechanincs, they can be used to predict the ultimats strength in flexure that can be achieved by such elements, given the cfrp cross - sectional area, or conversely, the required cfrp cross - sectional area to achieve a targeted resisting moment of rehabilitated flexureal elements
Cfrp加固梁在承受彎曲荷載時的破壞是鋼筋屈服后碳纖維斷裂和鋼筋屈服后混凝土壓碎。本文通過應變相容方法和對破壞機理的定義，由給定的cfrp橫截面積預測加固梁的極限彎曲強度；或者相反，在已知加固梁的極限彎曲強度時可以求出所需的cfrp橫截面積。At the same time in this paper we analyze nonlinear behavior of masonry through finite element method program and obtain its load when the wall start to crack and when it destroy, the p - u curve and so on. a comparison has been made between the data obtained from the experiment and the calculated through finite element method program so that we can study the cause of crack. in this paper we use finite element method to study concrete ' s character to analyze masonry, satisfactory results have been attained
因此本文在對灰砂磚砌體進行力學性能試驗的基礎上，分析其裂縫產生的破壞模式與開裂機理，並論述了將斷裂力學知識運用於研究砌體裂縫問題的可行性；同時，本文運用有限元方法對結構低周反復加載靜力試驗所做的灰砂磚墻片進行非線性分析計算，得出墻片的開裂荷載、極限荷載、 p ? u曲線，裂縫在墻體上的分佈等，與試驗所得數據對比，以便於研究裂縫的開裂機理，並將研究混凝土的有限元方法運用到對砌體的研究中，取得了較滿意的結果，為類似的試驗分析提供了一條新的思路。Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure
試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
分享友人