榫 的英文怎麼說
中文拼音 [sǔn]
榫
英文
名詞(榫頭) tenon-
Railway transport equipment. clevis and tenon joints. inner brass rings type bs
鐵路運輸設備. u形環和榫接頭.型銅制內環Boards tongued and grooved made of coniferous timber
針葉木製的接榫木板Chamfered boards tongued and grooved made of coniferous timber
針葉類木製開有榫和槽的削邊鑲板Secret mitre dovetail joint
暗接斜角鳩尾榫Through dovetail joint
貫穿鳩尾榫Single dovetail joint
單鳩尾榫First, the theory of fretting wear and studies on fretting fatigue were introduced and the parametric method was used in the process of creating the model of dovetail joints in ug software. the elastic contact problem is analyzed in finite element method ( fem ) and is used to the parameters " distribution and contact stress of the joint are obtained on the base of ansys code. with the effect factor of load frequency, the prediction method of fretting fatigue life of dovetail joint under low and high / low cycle complex load is proposed
本文介紹了微動損傷的機理和微動疲勞壽命的研究方法;利用ug軟體對燕尾榫聯接結構創建了參數化實體模型;基於ansys軟體平臺求解彈性接觸問題,獲得了榫聯接結構接觸應力及接觸狀態量的分佈;在已有微動疲勞壽命預測模型的基礎上,引入載荷頻率影響因子,對低周、高低周復合載荷作用下的燕尾榫聯接結構進行了微動疲勞壽命的預測,與試驗結果對比表明採用本文提出的方法預測榫聯接結構的微動疲勞壽命是有效的。Wood. assembly. multiple finger joints. flexion test
木材.組裝.多榫接頭連接.彎曲試驗Rolling stock. articulations with clevis and tenon and with gudgeon. inner steel rings type as, ag
鐵路車輛.帶u形環和榫的耳軸聯接. ,型鋼制內環Butt mitred joint
對接角榫Locks - mortice locks - part 1 : mortice locks for rebated doors
鎖.榫接鎖.第1部分:槽口門用榫接鎖The cross - piece is mortised into the upright post
橫梁和立柱是用榫眼接合一起的This seems to be a six - lever mortise, milady
這把鎖似乎是六榫眼的,夫人Woodworking machines - specification for slot mortising machines
木工機械.第12部分:開榫機規范Locks - mortise locks - part 3 : mortise locks as multipoint locks
鎖.榫接鎖.第3部分:多插頭榫接鎖Double planes for plane irons with central handle
帶中心柄刨刀的榫舌刨Mechanical tooling for wood. cutters for rabbet. dimensions
木材機加工刀具.榫口加工刀具.尺寸Through modeling experiment, this method is proved to be feasible for analyzing the rabbet assembly structure
通過模態實驗校驗的手段證明用這種方法進行榫接裝配系統動力學分析是可行的。Then the forging blade body is formed by fitting the data of forging blade to spline and b - surface, calling the rabbet and boss, generating the draft angle. then the related parameter is calculated
將鍛件型面數據擬合成樣條曲線、樣條曲面,調入榫頭和凸臺,作出模鍛斜度,生成葉片鍛件實體,並計算了鍛件的相關參數。Libraries ( driven by dimensions ) of rabbets and bosses are set up by user defined feature of ugh. the position relationships between the blade bodies, the rabbets and the bosses of the blade forging parts are studied
根據常用榫頭與凸臺形狀,總結其尺寸關系,利用ugii提供的用戶自定義特徵功能,建立了尺寸驅動的榫頭庫、凸臺庫,並提供了建庫方法。分享友人