構件抗扭剛度 的英文怎麼說

中文拼音 [gòujiànkàngniǔgāngdù]
構件抗扭剛度 英文
torsional stiffness of member
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 抗 : Ⅰ動詞1 （抵抗; 抵擋） resist; combat; fight 2 （拒絕; 抗拒） refuse; defy 3 （對等） contend with...
  • 扭 : 動詞1 （掉轉; 轉動） turn round 2 （擰; 旋轉） twist; wrench 3 （擰傷） sprain; wrench 4 （走路時...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. The results of the limited element analysis and experiment study confirms that both the resisting ended batten and using angle batten in place of plate one could make the laterally stiffness of such member more strong. that maybe provides somewhat practical benefits for designing the twin - wall truss

    本文還通過矩陣分析法和模擬試驗研究，證實了端綴板的存在對抵抗側向屈曲有明顯提高；而選用角鋼代替綴板材料相對于板形板，有助於提高構件的側移剛度和翹扭轉剛度，這對于單軸對稱綴板柱的設計也具有一定的實用價值。
  2. From above analysis, the thesis gets conclusions as following : ( 1 ) the frequencies of multi - tower building are so dense and the coupling in each mode is so evident that the cqc method instead of srss should be used to calculate the seismic action effect ; ( 2 ) torsion effects is distinct between the modes of asymmetry multi - tower structure and it is necessary to take translation - torsion coupling into account ; ( 3 ) the effect of the enlarged base rigid on the seismic properties is very big, the rigid ratio of the enlarged base to towers in asymmetry multi - tower structure should be designed in a proper range ; ( 4 ) the distribution of plane rigid is asymmetry because of the asymmetry layout of towers. the torsion effects of structure not only result in large torsion internal force in vertical element resisting lateral displacement, but also make large influences on the stress of transfer plate and near floors, thus it is necessary to strengthen those floors

    通過上述分析，得出以下主要結論：多塔樓結構存在頻率密集現象，各振型間耦聯效應明顯，地震作用計算應採用cqc組合原則而不能簡單地採用srss組合原則；非對稱多塔結構的振型中，扭轉作用明顯，平扭耦聯效應值得考慮；裙樓剛度對整體結構的抗震性能影響很大，非對稱多塔結構宜控制裙樓與塔樓剛度比在適宜的范圍；非對稱多塔易導致平面剛度分佈不均勻，結構扭轉效應不僅在豎向抗側構件中引起較大的扭轉內力，對轉換層樓板應力有較大的影響，且延續至相鄰樓層，對相應樓層均應採取相應的加強措施。
  3. Torsional stiffness of member

    構件抗扭剛度20
  4. The whole building can be equivalent to a cantilever bar, and the structural total displacements can be divided into parallel displacement and rotational displacement based on the harmonize condition of displacement, and the parallel shear and the rotational shear of the elements can be accordingly obtained by selecting the renegade body from top to bottom in turn

    根據位移協調條件，將結構的位移分解成平動與轉動成分，得到相應的結構平動時構件所承擔的剪力與結構轉動時構件所承擔的剪力，再根據力的平衡條件，推導出雙向地震作用下考慮構件抗扭剛度時結構的線彈性扭轉角，並對構件的剪力及變形進行了修正。
  5. Also the failure modes and the cracking torque, original stiffness, ultimate torsion strength and ductility are discussed in this case. the factors affected torsion bearing capacity of high - strength concrete frame column is analyzed too. the seismic performances of normal - strength and high - strength concrete frame column subjected to biaxial eccentric compression, shear and reversed torque are studied

    以軸壓比和相對偏心距為主要研究參數，揭示高強鋼筋混凝土構件在單向、雙向偏壓剪單調、反復扭矩作用下的破壞特徵、開裂扭矩、剛度、強度、延性等特性，分析了影響高強混凝土框架柱抗扭承載力的因素。
  6. Calculation of torsion performance of tall building structures based on torsion stiffness of elements

    考慮構件抗扭剛度的高層建築結構抗扭計算
  7. With the better torsion performance of box section beams and beam - columns than members with open cross - section and the progress of the manufacturing technology of box section members, the box section members find wider and wider application, especially in high rise buildings

    箱形截面梁與樑柱由於較其它形式的截面具有較好的兩個主軸方向抗彎剛度和抗扭剛度，隨著鋼結構的不斷發展，箱形構件製作工藝的完善和日趨成熟，箱形截面構件的應用越來越廣，尤其是在多高層建築中。
分享友人
分享到 Line

分享到臉書