槽內移動 的英文怎麼說

中文拼音 [cáonèiyídòng]
槽內移動 英文
intra-alveolar movement
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 內 : 名詞1. （內部; 里頭; 里邊） inner; inside; within 2. （妻子或妻子的親屬） one's wife or her relatives 3. （姓氏） a surname
  • 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
  • 移動 : 1 （改換原來的位置） shift; move 2 [力學] translation motion; removal; shifting; dislocation; dis...
  1. Based on the analysis of the kinetic track of the scallion during planting, basic relationships ' among the characteristic parameters of the transplanter with two flexible metal disks, including the velocity of the transplanter, the rate of transplanting, the spacing between seedlings, the angle of releasing seedlings, the diameter and length of seedlings, have been set up in this paper, and then a mathematic model of optimum design for the transplanter with the final planting angle of seedlings ( y = 90 ) has been formulated and solved with good results. according to the optimum solutions, a new type of transplanter with two flexible metal disks has been developed and the field tests of the transplanter have been conducted

    為了實現大蔥機械化移栽，作者分析了國內各種移栽機的結構特點，確定了以撓性圓盤式栽植器為研究對象，在分析撓性圓盤式栽植器的運動軌跡和特徵參數的基礎上，完整地確立了撓性圓盤式移栽機的基本參數：栽植頻率、栽植株距、機組前進速度、輸送帶上秧槽的間距、撓性圓盤半徑、撓性圓盤的轉速、夾苗株數以及傳動比之間的相互關系，並建立了以蔥苗栽植傾角= 90為目標的優化設計數學模型，提出了撓性圓盤式大蔥移栽機的優化設計方法。
  2. The equipment adopts centrifugal sliding plow groove rotor and is the newest structure evaporator at present. it can form membrane under the condition of small flow. comparing with that of fixed space drag evaporator, its evaporation capacity can increase 40

    本設備採用離心式滑動溝槽轉子，是目前國外最新結構蒸發器，在流量很小的情況下也能形成薄膜，在簡體蒸發段內壁表面附著處理液中的淤積物可被活動刮板迅速移去，和固定間隙的刮板蒸發器相比，蒸發量可提高40 69 。
  3. The blades can be movable in the slots during shaving

    剃削過程中，刀片能在凹槽內移動。
  4. When the belts have been located in the belt pulley grooves, moves the drive motor away from the driven shaft so that uniform teensioning of the belts is achieved

    在安裝新皮帶時，要用手動的方式使電機向驅動軸移動而使所有皮帶均處于滑輪槽內。
  5. The author has adopted sap2000 procedure to make 3 - d static and dynamic analysis and obtained the designing internal force, displacement and dynamic characteristic parameter of each element under different load cases

    對渡槽結構採用結構分析程序sap2000進行三維靜力和動力分析，得出了各類構件在不同工況下設計內力值、位移值以及渡槽的動力特性參數等。
  6. Analysis of gaseous slip flow and heat transfer in micro rectangular channels

    微矩形槽道內的氣體滑移流動和傳熱分析
分享友人
分享到 Line

分享到臉書