槽半徑 的英文怎麼說
中文拼音 [cáobànjìng]
槽半徑
英文
groove radius-
Powerformer have some changes in constract with the conventional generator ， subsequently it also have some new problems in order to have an economical ， efficient ， credible development and application the structure and the philosophy of electromagnetism of powerformer will be on speaking terms changes electrical design ， magnetism design ， thermal design and structural design are have some new changes above all ， the electromagnetism parameter and the harmonic magnetomotive force of powerformer are studied in this paper first ， it mainly utilizes analytics to deduce formula of slot leakage reactance it considers three instances ， including monolayer - slot ， multilayer isometric - slot and multilayer anisometric - slot then ， the analytics and the fem are utilized to calculate slot leakage reactance of stator winding of prototype of powerformer and compare their results second ， the theory of utilitzing fem to calculate the reactance of powerformer is simply introduced ， including stable reactance ， transient and subtransient reactance specially ， the saturated influence of the stable reactance is considered then ， the results are analysed final ， it mainly introduces the influence of harmonic magnetomotive force of stator winding and analyses the harmonic magnetomotive force of stator winding then ， it mainly analyse harmonic magneto - motive force of stator winding through arranging various arrays of stator winding and observe their influence
基於上述原因，本文對powerformer的電磁參數以及定子繞組諧波磁勢進行了研究。首先是用解析法推導出powerformer定子繞組槽漏抗的計算公式，考慮了單層圓形半閉口槽、多層等半徑圓形半閉口槽和多層不等半徑圓形半閉口槽三種情況，並對powerformer樣機的定子繞組槽漏抗用解析法和有限元法進行了計算，並比較其結果；其次，簡要介紹了有限元法計算powerformer電抗參數的原理，包括穩態電抗、瞬態電抗和超瞬態電抗，對穩態電抗考慮飽和影響，對結果進行分析；最後，介紹定子繞組諧波磁勢對電機運行性能的影響並對定子繞組諧波磁勢進行了分析。然後通過對定子繞組進行不同排列來分析定子繞組諧波磁勢，看看繞組排列對諧波磁勢的影響。The compliance-calibration specimen has a slot of finite-tip radius in place of a crack.
柔度算定試樣是用一個有限端部半徑的槽來代替裂紋。Chip breaker groove radius
斷屑槽底半徑Based on the analysis of the kinetic track of the scallion during planting, basic relationships ' among the characteristic parameters of the transplanter with two flexible metal disks, including the velocity of the transplanter, the rate of transplanting, the spacing between seedlings, the angle of releasing seedlings, the diameter and length of seedlings, have been set up in this paper, and then a mathematic model of optimum design for the transplanter with the final planting angle of seedlings ( y = 90 ) has been formulated and solved with good results. according to the optimum solutions, a new type of transplanter with two flexible metal disks has been developed and the field tests of the transplanter have been conducted
為了實現大蔥機械化移栽，作者分析了國內各種移栽機的結構特點，確定了以撓性圓盤式栽植器為研究對象，在分析撓性圓盤式栽植器的運動軌跡和特徵參數的基礎上，完整地確立了撓性圓盤式移栽機的基本參數：栽植頻率、栽植株距、機組前進速度、輸送帶上秧槽的間距、撓性圓盤半徑、撓性圓盤的轉速、夾苗株數以及傳動比之間的相互關系，並建立了以蔥苗栽植傾角= 90為目標的優化設計數學模型，提出了撓性圓盤式大蔥移栽機的優化設計方法。Well radius top
槽頂圓角半徑If the confirmed size from the above formula is not practical, it is necessary to apply flange wheel hub and checking board, the checking board should be connected with gear with bolt, and the bolt should be on special pitch circle radius
21 . 1如果從上面公式確定的鍵槽尺寸不實用，那麼應採用帶鍵的法蘭式輪轂和檢查板，檢查板用螺栓連接在輪上，螺栓處于特別的節圓半徑上。Well iner radius
槽底半徑The paper analyses affecting on - movement law of special cam that by transition arc radius of special cam, we conclude that transition arc radius should be great than half of groove ' s width and that sharp - angled transition will bring excessive removal while nc - machining
摘要對空間凸輪的過渡圓弧的半徑大小對凸輪運動規律的影響進行了分析，得出過渡圓弧半徑應大於槽寬的一半，尖角過渡數控加工時會產生過切現象。R average key way radius
R平均鍵槽半徑分享友人