槽型 的英文怎麼說

中文拼音 [cáoxíng]
槽型 英文
groove profile
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  1. Narrow gauge mine car open type wheel assembly castle nuts

    礦山窄軌車輛.開式輪對.槽型螺母
  2. Grooved pins. full length paralled grooved, with chamfer

    帶槽銷.有倒角的全長度直槽型銷
  3. Iron and steel. 70 g grooved rail and its fish plates

    鋼鐵. 70mmg槽型軌和其魚尾板
  4. Iron and steel. 60 g grooved rail and its fish plates

    鋼鐵. 60mmg槽型軌和其魚尾板
  5. Concrete kerb units - requirements and test methods - national addition to nf en 1340 : concrete industrial products - kerbstones and gutters - profiles

    混凝土路邊石.要求和試驗方法. nf en 1340的國家補充件:混凝土工業產品.路邊石和水槽.型材
  6. This bridge was built with precast channel girder sections, but could be built with aashtoi girders or box sections.

    該橋是採用預制的槽型梁修建的，但是也可利用AASHTOI的標準工型梁或箱型梁修建。
  7. Web - based machining chip - breaking predictive system of three - dimensional grooved inserts

    基於網路的三維槽型刀片斷屑預報系統研究
  8. Dimensions of clevis and tongue couplings of string insulator units

    絕緣子串元件槽型和扁腳連接的尺寸
  9. It can be classified as u - tube tank stabilizer and flume anti - rolling tank according to structural configuration, and the former has three types, namely passive, active control and controlled passive tank in terms of the control mode

    減搖水艙按結構形式可分為u型減搖水艙和槽型減搖水艙，而u型減搖水艙可以設計成被動式、主動控制式和可控被動式三種。
  10. Flute type deformation

    槽型形變
  11. The study of insert groove on chip - breaking mechanism

    刀片槽型對斷屑性能的實驗
  12. Fea of the broken processing of the insert with complex three - dimension chip - breaker

    復雜三維槽型刀片斷屑過程有限元分析
  13. Prediction of the breaking area of 3 - d chip former using rbf neural networks

    神經網路在可轉位三維槽型刀片斷屑范圍預測中的應用
  14. In the test of transmission coefficient property, semi - circle type, rectangle type, trapezoid type and concave type dyke are studied. research study is on the effect of relative water depth over the dyke to the transmission coefficient of the four different types dyke, and the comparison is done. finally, the experimental formula is given to the transmission coefficient, which are compared with the present formulae

    在潛堤透射特性的研究中，選取半圓型、矩型、梯型和槽型潛堤作為研究對象，在分析各個影響因素對潛堤透射影響的基礎上，選取最主要的影響因素，即相對堤頂水深作為研究的重點，分析研究了堤頂相對水深對四種結構型式潛堤透射系數的影響，比較分析了四種結構型式潛堤透射特性，在此基礎上，總結了計算潛堤透射系數的經驗公式，並與已存在的計算公式進行了對比，最後對潛堤的促淤效果進行了評估。
  15. Screw conveyors - specification for fixed trough type

    螺旋輸送機.第1部分:固定式槽型規范
  16. Reduced hexagon thick slotted nuts with mj thread

    Mj螺紋小六角槽型厚螺母
  17. Reduced hexagon slotted thick nuts with mj thread

    Mj螺紋小六角槽型厚螺母
  18. A kind of drainage material consisting of a white polypropylene channel - shaped core surrounded by a gray long - fiber hot - bonded non - woven filter fabric, with metal conductor inside for measuring the driven depth

    灰色長纖維熱粘無紡布濾膜包裹（通過粘合）白色聚丙烯槽型芯板組成的排水材料，內裝配金屬電子導線用於測量打設深度。
  19. This problem mainly involves two parts. of course, there are many factors affecting chip ' s type, but the most important factor is tool ' s groove type. so it is necessary to study tool ' s groove

    切屑控制最主要的兩個方面是切屑折斷和切屑處理，而在影響切屑形成與折斷的諸多因素中，刀片斷屑槽型的影響最大，所以，研究斷屑槽型是十分必要的。
  20. Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly

    摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。
分享友人
分享到 Line

分享到臉書