槽鍵 的英文怎麼說

中文拼音 [cáojiàn]
槽鍵 英文
sunk key
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 鍵 : 名詞1 [機械工程] （使軸與齒輪、皮帶輪等連接並固定在一起的零件） key 2 [書面語] （插門的金屬棍子）...
  1. Keyway broach with chamfer types and dimensions

    帶倒角齒鍵槽拉刀型式與尺寸
  2. Bores and keyways for flexible couplings metric series

    柔性耦合器的鏜孔和鍵槽
  3. Bores and keyways for flexible couplings inch series

    柔性耦合器的鏜孔和鍵槽
  4. Stressed - type fastenings with taper action ; taper keys with gip head, keyways, dimensions and application

    錐度驅動應力型緊固件.彎頭斜鍵鍵槽尺寸和應用
  5. Five key groove bit multiple keys bit hexagonal bit

    五鍵槽花鍵六角鉆頭
  6. For the 30. 2mm shaft, there are still larger over measure to load. the strength is increased by optimization. for ? 17. 4mm shaft, the strength is increased by enlarge the inner dimension of the spline ; for 30. 2mm shaft, the strength is increased by adjust the structure at the boundary between the key groove and the ring groove, the highest stress of the shaft is at bottom and terminal of the spline after optimization

    其中對17 . 4mm泵軸的優化，通過增大花鍵內徑，提高了花鍵齒底的強度，降低了應力集中點附近的應力；對30 . 2mm電機軸的優化，通過在軸承鍵的環槽端增加倒角，有效降低了該位置的應力集中，使軸的最大應力點從軸承鍵與環槽的交界處轉變到花鍵根部與收尾的交界處，提高了電機軸整體結構強度的合理性。
  7. Widened flat body keyway broach types and dimensions

    加寬平刀鍵槽拉刀型式與尺寸
  8. Tool inspection methods part 19 : keyway broaches

    刀具產品檢測方法.第19部分:鍵槽拉刀
  9. Flat body keyway broach types and dimensions

    平刀體鍵槽拉刀型式與尺寸
  10. Technical specifications for keyway broaches

    鍵槽拉刀通用技術條件
  11. Washer for keyway broaching. dimensions

    鍵槽拉削用墊片.尺寸
  12. Holder for keyway broach. dimensions

    鍵槽拉刀夾頭.尺寸
  13. Was the keyway created using a min arc condition dimension of. 0. 63

    鍵槽的生成是用了0 . 63最小圓狐的尺寸條件。
  14. Bearing sleeves for milling machine arbors, for milling cutters with longitudinal keyway

    第1部分:銑床心軸用和帶縱向鍵槽的銑刀用軸承座套
  15. Rod - ends with self - aligning ball bearings. long threaded shank and keyway. dimensions and loads

    帶自位球軸承的桿端.長螺紋桿和鍵槽.尺寸和負荷
  16. Table 5. the max key way stress of the contunious running gear sk

    表15 .連續工作輪的最大允許鍵槽應力sk
  17. Serrations for surgical instruments ; profile angles, groove distances

    外科器械的細花鍵連接.齒形角槽的間距
  18. Tangential keys and tangential keyways for alternating shock loads

    交變沖擊負荷用切向鍵與切向鍵槽
  19. Shell end mills with tenon and parallel key drive ; dimensions

    帶榫和平行鍵槽的筒形端銑刀.尺寸
  20. Semi - circular woodruff keys - dimensions of cross sections and keyways

    鍵和鍵槽的剖面尺寸
分享友人
分享到 Line

分享到臉書