模具溫度 的英文怎麼說

中文拼音 [mójùwēndù]
模具溫度 英文
o mold temperature
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 模具 : mould; matrix; pattern die; die模具鋼 die steel
  • 溫度 : [物理學] temperature
  1. This will reduce and equalize mold temperatures.

    這樣會降低和均衡模具溫度。
  2. Injection molding too satuated molding temperature too low

    3模具溫度過低。
  3. The green body of high quality could be obtained at injection molding temperature from 160c to 180 c, injection molding pressure from loompa to 120mpa, keeping pressure from 40mpa to sompa, mold - temperature 32c, cooled from 2 min to 4 min

    注射溫度為160 180 ，注射壓力為100 120mpa 、保壓壓力為40 50mpa 、模具溫度為32 、冷卻時間為2 4min注射成型后，注射坯的質量較好。
  4. Mold temperature is controlled by water flow in cooling channels.

    模具溫度可用冷卻槽中水的流動來控制。
  5. The sensitivity algorithm is a knowledge of research on the affection of parameters varies to system performance. combination with pressing force and infuse time predicted model, by using sensitivity algorithm, the affection of cast temperature, mould temperature and infuse pressure on infuse time is researched deeply, and the affection of cast temperature, infuse time and infuse pressure on the pressing force in the origination stage of extrusion process. the sensitivity analysis has huge instructing significance to the selection of parameters

    靈敏度演算法是分析參數變化對系統性能影響的一種有效工具，所以本文引入靈敏度演算法，結合壓制力和浸滲時間預測模型，深入研究了澆注溫度、模具溫度和浸滲壓力對浸滲時間的影響關系，以及澆注溫度、模具溫度、浸滲時間和浸滲壓力對擠壓過程起始階段壓制力的影響，對于參數的選取，具有一定的指導意義。
  6. 3 stages of temperature control, 2 levels of injection pressure, non - stage abjustment injection speed and back pressure, be suitted in precise shaping of engineering plastic

    料筒油溫控制，兩極注塑壓力，射速、背壓無段調整，上、下模具溫度獨立控制。
  7. Mould temperature is constant when no one is operating

    在無人操作的狀態下，模具溫度是恆定的。
  8. Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times

    加工窗口分析、其它零件的模流分析，檢查熔體溫度、模具溫度、注塑壓力和充填時間。
  9. Based on the numeric analysis of the model, the effects of melt temperature, injection time, mold temperature and pre - filled volume on the cell size were studied especially

    在對該數學模型進行數值分析的基礎上，著重研究了熔體溫度、注塑時間、模具溫度、初始填充量對微泡尺寸的影響。
  10. The solution is to attach a device to measure the clamping force and to control the clamping force to within a tolerance as mould temperature changes

    解決辦法是安裝一個裝置在模具溫度改變時去測量鎖模力並且將其控制在一個公差范圍內。
  11. Reduce barrel and mould temperature

    降低機筒和模具溫度
  12. Boundary element simulation of the temperature field of ti - 1023 alloy isothermal - forging mold

    1023鈦合金等溫鍛造模具溫度場的邊界元模擬
  13. Thermal fe analysis can predict punch and die temperature distribution during the cooling process. holes drilled in the die allow for faster cooling

    溫度有限元分析可以預測冷卻過程中沖床和模具溫度的分佈，模具中沖孔的冷卻速度比較快。
  14. It consists of upper and lower supporting cores, and has the function to open mould at six directions. the japanese plc is used as the computer control system for the machine, and omron digital display controller is used as the temperature control in order to guarantee the absolute balance of the temperature of the upper and lows dies

    本機是水平分型全自動射芯機，它具備上、下頂芯及六個方向開模的功能，採用plc控制、 omron數顯溫控儀，保證上、下模具溫度的絕對均衡。
  15. Melt temperature and or mould too cold

    熔化和或模具溫度太低
  16. Study on temperature control of mould for plastic microstructure part

    微結構塑件模具溫度控制探討
  17. Poor temperature control of mould

    模具溫度控制差
  18. Study and application of the temperature distribution in molds

    注塑模具溫度分佈規律的研究及應用
  19. Study on temperature field of dies in die casting process of magnesium alloys

    壓鑄鎂合金模具溫度場分佈的研究
  20. Mk series mould temperature controller

    Mk系列模具溫度控制器
分享友人
分享到 Line

分享到臉書