模具結構 的英文怎麼說

中文拼音 [mójùjiēgòu]
模具結構 英文
mold construction
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 模具 : mould; matrix; pattern die; die模具鋼 die steel
  • 結構 : 1 （各組成部分的搭配形式） structure; composition; construction; formation; constitution; fabric;...
  1. Configuration of plastic packaged mould. pre - heating unit

    塑封模具結構.預熱座
  2. The inside fashion of the sway oil pump stator is complex, its wall thickness is pockety and the metal flow law is difficult to master. at the present time, the investigation of warm extrusion forming technique for the nonuniform wall thickness forging has few to been done. the forming technique and die configuration which use for production have not achieve optimization

    由於轉向油泵定子的內部形狀復雜，零件壁厚分佈不均，金屬流動規律難于掌握，目前人們對這種非均勻壁厚鍛件的溫擠壓成形工藝研究幾乎沒有，其成形工藝及生產用模具結構並未達到最優化。
  3. We make moldings strictly according such process, plan and assign jobs, designing the mould structure, rough working, accurate working, test, benchwork assembly, post treatment, test and production. we adopt standard moulding accessorics in order to make our customer fast and accurately get what they need at any time

    我們嚴格按照「策劃分配任務?模具結構設計?粗加工?精加工?檢測?鉗工裝配?后處理?檢測?生產」的生產工藝流程進行模具製造，採用標準化的模具配件讓我們的客戶隨時、快捷、準確地獲取您之所需。
  4. In the paper, the finite element simulation software dynafrom is applied to analyze the affect of different blank holder during the forming process of laminose stepped tubular part, predict the possible defects such as wrinkle and break, obtain the rational style of blank holder avoiding the occur of defects and determine the rational configuration of die. the forming affect of thin - wall shallow stepped tubular part is analyzed when using different lubricate condition ( friction coefficient ). by this method, the relationship between friction coefficient and drawing depth of laminose stepped tubular part is obtained

    本文利用有限元模擬軟體dynafrom分析了不同類型的壓邊圈對薄壁階梯筒形件成形過程的影響規律，預測了採用不同類型壓邊圈時可能出現的成形缺陷如起皺和拉裂，獲得了防止缺陷產生的合理壓邊圈形式，確定了合理的模具結構形式；分析了不同的潤滑條件（摩擦系數）對薄板階梯筒形件成形的影響，獲得摩擦系數與薄板階梯筒形件的拉深深度的關系；分析了階梯筒形件成形過程中的不同階段的應力應變分佈、毛坯材料厚度變化情況，並獲得了階梯階梯筒形件能一次拉深成形的條件。
  5. The non - uniform deformation behavours and the movement of the weld seams, the wrinkling of the workpieces and the methods to control the non - uniform deformation were investigated by adjusting the die structures, the blank holding method and the blankholding force distribution

    通過調整模具結構和壓邊方法及壓邊力分佈，對坯料不均勻變形規律及焊縫的移動規律、坯料的起皺規律及控制坯料不均勻變形的方法進行了探討研究。
  6. The cold shaping process and die structural of egg - shaped cylindrical shell

    卵形截面柱殼型模冷壓彎成形工藝及模具結構
  7. Based on the technological analysis of the auto front lamp holder plate with 3 angles, the layout for forming the part with a multi _ position progressive die and the structure of the die were put forward

    在對汽車前燈座三角盤進行工藝分析的基礎上，提出了該零件多工位級進沖壓成形排樣方案及相應的模具結構。
  8. The traits of progressive die for ic lead frame have been introduced with emphasis on the ironing stage in layout design and stripping micro - adjustment, safety setup of the structure

    摘要紹了ic引線框架級進沖模的特點並著重講述了其排樣設計中的整形工位和模具結構中的卸料、微調和安全機構，可供精密級進沖模設計參考。
  9. Abstract : having been finished the design of squeeze casting machine shell model, it provides design key points of squeeze casting model with slant slide parts, researches the technology about the product and optimizes the parameters of technoloy and model structure. the results are suitable for similar squeeze casting of parts

    文摘:通過對機座擠壓鑄造模具的設計，給出了斜滑塊擠鑄模的設計要點，研究了製件的工藝過程，對工藝參數和模具結構參數進行了優化，研究結果可供類似零件的擠壓鑄造所借鑒
  10. The forming technology data have been defined on the analysis of the forming technology of az31 magnesium alloy thin - walled tubes by using isothermal forming and forward extrusion deforming of hollow blank process and the design of die structure has been introduced

    摘要本文通過對az31鎂合金薄壁管材成形的工藝分析，採用了空心坯正擠壓、等溫成形的工藝方法，確定了其成形工藝參數，並介紹了該薄壁管材的擠壓模具結構設計。
  11. Based on testing repeatedly, the structure of mould is further optimized and the technological parameter is further optimum seed, a reasonable lubricating way and annealing mean is lain down

    通過試驗研究，進一步優化了模具結構，優選了工藝參數，制定了合理的退火規范和潤滑方式。
  12. A mould with an oblique guide pin scroll box structure was designed for the core pulling in two directions of a mould with two cavities

    採用能解決一模兩腔的兩面抽芯問題的斜導柱滑塊結構的模具結構，設計出電流線圈架注射模模具。
  13. The mold design subsystem is divided into two modules which one is mold structure design and the other is mold component design

    模具設計子系統分為模具結構設計和模具零件設計兩個模塊。
  14. The system involves five parts : soft - cpu, expert system of mold structure, data input, punch - pressing technology analyses and calculation, mold design

    本系統包括五個子系統:軟cpu子系統、模具結構專家系統、數據錄入子系統、沖壓工藝分析計運算元系統、模具設計子系統。
  15. In the thesis, the author researches how to express the die case, organize the case base, and retrieve the case. at ( he key nearest algorithm system, fuzzy reasoning is used to retrieve the case according to the similarity between the die structure cases. the system also provide a strategy to reuse the retrieved case and make the system can study by itself

    論文中提出了模具智能化cad系統的體系架構和智能化方案；將基於實例推理的技術應用到模具結構設計當中，針對這個問題詳細的討論了模具結構實例的表達，模具結構實例庫的組織，模具結構設計過程當中針對具體的應用情況如何進行模具結構實例的檢索；本文應用模糊推理技術採用了權值鄰近法根據模具結構實例之間的相似度進行模具結構實例的檢索，並且給出了系統再學習的具體策略，使整個系統具有自學習的功能。
  16. In this paper, the cold die forging technology of the counter gear was analysed, the cold die forging was designed, the blank dimensions and the figure were calculated and choosed, the allowable deformation degree was checked, the equipment for the deformation was selected, the blank treatments before the cold die forging were draw up and the die structure of the cold die forging was designed

    分析了計數器齒輪的冷模鍛工藝，設計了冷模鍛件圖，計算及選用了毛坯尺寸及形狀，驗算了許可變形程度，選擇了變形用的設備，擬制了冷模鍛前的毛坯處理及設計了冷模鍛模具結構。
  17. Abstract : in this paper, the cold die forging technology of the counter gear was analysed, the cold die forging was designed, the blank dimensions and the figure were calculated and choosed, the allowable deformation degree was checked, the equipment for the deformation was selected, the blank treatments before the cold die forging were draw up and the die structure of the cold die forging was designed

    文摘:分析了計數器齒輪的冷模鍛工藝，設計了冷模鍛件圖，計算及選用了毛坯尺寸及形狀，驗算了許可變形程度，選擇了變形用的設備，擬制了冷模鍛前的毛坯處理及設計了冷模鍛模具結構。
  18. Abstract : this paper analyses the structure characteristics, die structure and design plan of qd1212 driving terminal. the sliding part design is becoming more ideal after several times of modification

    文摘:分析了qd1212驅動端蓋結構特點，壓鑄件模具結構及設計方案；該模具滑塊部分的設計經過多次修改後更趨合理，鑄件易於脫模。
  19. Its reliability has been tested though examining. the influence laws of mould structure, including wiper die and the style, size and installed position of mandrel, have been studied. combined with the theoretical analysis of perfect pure bending, the tendency of relative bending radius r / d and relative wall thickness t / d to one of the major quality target - the maximum wall thickness reduction ratio is also studied

    通過數值模擬研究獲得了包括防皺塊和芯棒形式、尺寸和安裝位置在內的模具結構對製件成形質量的影響規律；結合對理想純彎曲的理論分析，研究獲得了相對彎曲半徑r / d 、相對壁厚t / d對製件主要質量指標之一的最大壁厚減薄率的影響趨勢和大小。
  20. For improvement of effectivity and reduction as much as possible of reciprocaing motion stroke o f oil press, amplifier - mechanism of distance has been applied to structure adde d hence realization of speed autotransmitting

    為了能提高效率，讓油壓機往復運動行程盡量縮短，模具結構中採用了增距放大機構並分析了實際應用中出現的誤差，增加了可調結構，可完全實現快速自動上下料。
分享友人
分享到 Line

分享到臉書