模壓收縮率 的英文怎麼說
中文拼音 [móyāshōusuōlǜ]
模壓收縮率
英文
constriction allowance-
With the established rf front - end system simulation platform, adding the digital modulated baseband signal, this paper simulated the multifold digital modulated signal ’ s transmission, such as 2ask, qpsk, and 16qam. then researches of power compression and phase noise of local oscillation influence the bit error ratio for different modulated system. the designing is satisfied multifold functions request with the high - powered and integrated broadband rf front - end
隨后在建立的寬帶射頻前端通用模擬平臺上，加入基帶數字調制信號，對多種數字調制格式的信號在該通用平臺上的傳輸作了研究，模擬了2ask 、 qpsk和16qam等調制格式信號的發射與接收，研究了功率壓縮和本振相位噪聲對不同調制的誤碼率影響，實現了滿足多種功能要求的寬帶高性能綜合射頻前端的設計。The results showed that the intensity of uterine contraction was reinforced by mifepristone and misoprostol used in combination ; and the random uterine contraction was effectively inhibited and the effective uterine contraction was strengthened by acupuncture
為探討針刺、藥物抗早孕的作用機制，我們採用早孕大鼠模型，建立間接反映子宮內壓的記錄方法，安放電極記錄子宮收縮頻率、強度作為判斷宮縮變化的指標，科學、簡便、靈敏、客觀地記錄宮內壓變化及子宮收縮情況。With the different loading ratio of parallel to axis and normal to axis direction, damage defects will occur bulking problem. by varying the degree of material anisotropy relative to the loading axis such as poisson ' s ratio and shear modulus, crack growth bulking strain value parallel to or normal to the loading axis is different. the parameters controlling the growth or arrest of the delamination damage are identified as the geometry and the depth of defects and radius of cylindrical etc. at last, it was investigated that the delamination damage is often induced by the tip of matrix damage under higher stress
研究結果表明:殼體筒段受軸向拉伸和內壓載荷作用時，軸向和環向載荷的比率不同，母層和子層可能發生拉伸屈曲，也可能發生收縮屈曲，或者同時發生拉伸和壓縮屈曲;母層與子層各向異性存在差異，即泊松比與剪切模量不匹配時，將使子層板的邊界上承受壓縮和剪切作用，當分層達到臨界狀態則發生屈曲，當母層與子層的各向異性差異越大，則發生分層屈曲的可能性越大;分層損傷的屈曲應變值與子層自身的彈性模量、分層子層的形狀、厚度以及圓柱半徑等因素有關。Based on the comparative analysis of two available heat system plan, the paper selects the water - water heat pump system plan. after a series of character analysis, design calculation ; the style of compressor including media choosing and its circle dynamic calculation for the thermodynamic system is determined. besides this, based on some basic measure of thermodynamic analysis, the heat pump coefficient of performance is discussed ; the exergy analysis for the water - water heat plan is conducted ; the calculation formula of heat pump exergy efficiency is derived ; an optimal model for heat pump together with thermal machine is established and the main exchanger equipment in heat pump system including its resistance calculation is designed in details
本文通過對兩種系統方案進行比較分析，確定了水環熱泵系統的基本方案，經過定性分析和設計計算，進行了壓縮機的選型、工質的選擇、熱力系統的循環計算等基本設計，同時應用熱力學分析的一些基本方法，討論了如何評價熱泵系統的性能系數，並對電廠循環水余熱回收熱泵系統進行了（火用）分析，得到了熱泵過程（火用）效率的計算公式，建立了熱泵?熱機聯合機組優化模型，還對熱泵系統的主要換熱設備進行了詳細的結構設計和阻力計算，最後對熱泵系統進行了技術經濟分析和評價。Controlling shrinkage ratio and surface - quality through optimization of process conditions in smc molding
模壓工藝控制製品收縮率和表面粗糙度分享友人