模壓螺紋 的英文怎麼說
中文拼音 [móyāluówén]
模壓螺紋
英文
stamped thread-
Main products include suited offset point imprinter bearing sets comber gear for weaving industry metal mould and gear vacuum gear synchro gear worm worm wheel. acme whorl fitting and all kinds of fittings with various gears
主要產品：印刷行業各種膠印機和印后設備輪及軸承套，紡織行業精梳機輪，金屬板材壓延模具和輪，真空泵輪同步帶輪蝸桿蝸輪副acme螺紋副各種直斜錐及各種盤類和軸類件等機械加工件。Insert nuts ; heavy type for plastics mouldings and pressure die castings with dead hole
嵌入螺母.第4部分:塑料模製件和壓鑄件用重型閉式螺紋In the construction of the tanghe inverted siphon on mid - roule of south - to - north water transfer project, some reliable construction processes and techniques are applied such as belt conveyor with three - rail gantry, construction with combined steel formwork, straight screw sleeve connection for reinforcement and the crushed stone - planting method etc., by which better construction effects are obtained
摘要南水北調中線唐河倒虹吸工程項目施工中，根據工程特點，採用了三軌門架式皮帶布料機、鋼模板聯體施工、鋼筋滾壓直螺紋套筒連接、混凝土施工縫栽石法等可靠的施工技術和施工工藝，取得了較好的效果。This is a thread producing machine which uses its three thread rolling dies, mounted in the same seperation angle of 120 ', to realize roll forming of the workpiece, for metal has the performence of plastic deformation under the pressure operation
該機床是利用金屬在壓力之下產生塑性變形的特點，用三個互成120度夾角的滾模，對工件進行滾壓成型的螺紋加工設備Demoulding mechanism of taper thread and hydraulic pressure side core - pulling mechanism, gating system and other structures were designed for the mold, and the working process of the mould was described in detail
在模具中設計了圓錐螺紋脫模機構、液壓側抽芯機構、澆注系統和其它結構的設計，以及模具工作過程。Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly
摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。The mesh of copper tubes and loading ways of the balls are the key problems during three dimensional fe simulation of ball spinning of inner grooved tubes
摘要內螺紋管滾珠旋壓三維有限元模擬中，銅管的網格劃分和滾珠加載方式是模擬的關鍵問題。Successfully simulated and replayed the complicated ball spinning of inner grooved tubes through the establishment of simplified sixth rotational symmetrical fe model and the adapting of local remeshing techniques
通過建立簡化的六分之一旋轉對稱模型和採用網格局部重劃分技術，成功地模擬和再現內螺紋管滾珠旋壓成形過程。Engineering drawing system can draw two dimension curve graphs, main detail drawing and assembly drawing. the curve of internal trajectory and dynamic simulation of particle external trajectory. the detail drawing includes the graph of chamber, grain design, connection body, nozzle, some standard part
工程繪圖可以繪制二維曲線圖和零部件圖，其中二維曲線包括有內彈道壓（推）力?時間曲線、質點外彈道動態模擬曲線；零部件圖包括有標準螺栓與螺紋孔、燃燒室結構圖、裝藥設計截面圖、連接底結構圖、噴管結構圖及火箭發動機總體裝配圖。分享友人