機軸限速器 的英文怎麼說
中文拼音 [jīzhóuxiànsùqì]
機軸限速器
英文
shaft governor- 機 : machineengine
- 軸 : 軸Ⅰ名詞1. (圓柱形的零件) axle; shaft 2. (對稱部分的直線) axis 3. (圓柱形的纏繞器物) roller; spool Ⅱ量詞(用於纏在軸上的線以及裝裱帶軸子的字畫)
- 限 : Ⅰ名詞(指定的范圍; 限度) limit; bounds Ⅱ動詞(指定范圍, 不許超過) set a limit; limit; restrict
- 速 : Ⅰ形容詞(迅速; 快) fast; rapid; quick; speedy Ⅱ名詞1 (速度) speed; velocity 2 (姓氏) a surna...
- 器 : 名詞1. (器具) implement; utensil; ware 2. (器官) organ 3. (度量; 才能) capacity; talent 4. (姓氏) a surname
- 限速 : maximum speed / speed limit
-
One new type double backspin rotor type sand mixing machine passes technique appraisal of qingdao tianheng machinery co., ltd. this machine adopts double rotor configuration researched internationally ; the rotor is installed on different output axis of same reducer, which produces comparative cross cutting speed by using rotors with different speed that makes sands get strong cutting and friction force. therefore, it can reduce clay and quicken sand mixing
一種新型雙逆轉子式混砂機在青島天恆機械有限公司通過技術鑒定,該機採用國際首創的雙轉子結構,其轉子安裝在同一減速器的不同輸出軸上,利用兩個軸的不同轉速使轉子間產生相對交叉剪切速度,使砂子受到的沖剪及搓擦力加強,從而減少粘土團,加快砂子的混合。In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology
為使二維振動傳感器在兩主軸方向的靈敏度大致相同,敏感元件採用高度對稱的四梁結構,其中每個軸向上均採用帶折疊梁的雙側叉指電容結構,採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件,具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算,並利用有限元法進行了模擬分析,根據模擬結果得出了優化參數;在確定敏感結構的基礎上,研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析,利用差動測量技術得到由振動引起的微小電容變化量,經c - v介面電路進行相位調制處理,然後通過解調輸出與加速度成正比的電壓信號。Trued cylindricity and enhanced fitting configurations in major bearing areas reduce stretching and greatly increase chain life. our unique shot - peened surface layer, with residual compressive stress considerably improves fatique properties. kmc is a leading manufacturer of bicycle, motorcycle, automobile and industrial transmission chains
Kmc桂盟集團是全球居領導地位的自行車摩托車汽車和工業傳輸鏈條製造商,工業傳動事業部經營產品項目包含標準鏈條皮帶馬達非標鏈條皮帶輪傳動配件輪同步輪鏈輪扭力限制器聯軸器減速機等。One pencil is the simulative milling cutter. parameters setting, milling cutter radius compensation, graphics drawing of the work - piece machined, realizing local control, etc. are the tasks of pc, while line & arc interpolation, motion segment acceleration & deceleration control, position protection at a high precision rate and so on are the duty of dsp motion controller. in the end, the system can draw the cutter center track of the work piece ' s program track accurately
上位pc機主要完成相關參數設定、刀具半徑補償相關運算及繪制被加工工件的輪廓(程編軌跡) 、實現本地控制等內容;下位機dsp控制器則充分利用美國ti公司的tms320c31浮點dsp的高速度、高精度完成運動控制中的實時直線和圓弧數值插補、運動段加減速控制、運動軸行程限位保護等內容。The table is a important device in the hardware - in - the - loop simulation system, and it simulates the flight of unmanned aerial vehicle so as to achieve flying parameters from those sensors. the signals of sensors in the table are transmitted by many cables previously, thus it confines the movement range of the three - axis frameworks. as the perfomance of uav become complicated, the signals cables are replaced by wire rings in some tables, but it brings many difficulties and unreliable factors for the simulation table ’ s design also. bluetooth, as a new short - range wireless communication technology, is a reasonable and feasible scheme in this condition
三軸模擬轉臺是無人機地面半實物模擬系統中的重要設備,用來模擬飛機在空中的姿態和角運動,以驅動傳感器產生飛行姿態、角速度及角加速度信號。早期轉臺上傳感器信號通過穿在框架中的電纜進行傳輸,這就限制了框架的運動范圍。隨著無人機任務的復雜程度不斷提高,出現了採用導電滑環傳遞信號的模擬轉臺,但這也給轉臺設計帶來了困難,且存在不可靠因素。分享友人