橫向撓曲 的英文怎麼說

中文拼音 [héngxiàngnáoqū]
橫向撓曲 英文
cross flexure
  • 橫 : 橫形容詞1. （蠻橫; 兇暴） harsh and unreasonable; perverse 2. （不吉利的; 意外的） unexpected
  • 撓 : 動詞1. （輕輕地抓） scratch 2. （擾亂;阻止） hinder 3. （彎曲,比喻屈服）yield;flinch:不屈不撓indomitable; unyielding
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 橫向 : broadwise; infeed; crossrange; abeam;transverse; transverse direction; cross; crosswise; lateral;...
  1. As an application of this fem preprocessing system, the simulation on the welding process of missile ’ s oil box was performed, in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed. the simulation results show that the deformations under varied welding sequences are almost the same. downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction

    對于某型號導彈油箱結構焊接過程的數值模擬計算，主要考察了每塊立板上各段焊縫焊接順序的調整、四塊立板之間不同的焊接順序以及焊接起始端的選擇對結構焊后變形的影響規律，模擬結果表明:壁板在各種焊接順序下的整體變形規律基本相似，即焊後壁板沿焊縫縱向發生了向下的撓曲變形，中部向下變形量最大;沿焊縫橫向發生了向上的撓曲變形，壁板兩端部變形量較大，且壁板前端變形大於壁板後端。
  2. In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered

    確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  3. Observing the mechanics and effect of the new strengthening method with test and finite element method is supposed to offer a guide for technology and become valuable in theory and practice. both compression test, including four reinforced and three control specimens, and shear - compression test, including nineteen reinforced and four control specimens are being studied in this paper. the research on the curves of load - strain, load - deflection and hysteretic shows that the transverse translation of the reinforced columns is well controlled with an upgrading of both ductility and ultimate bearing capacity ( ubc )

    本文對4根鋼絲網外噴高強砂漿加固鋼筋混凝土柱和3根對比鋼筋混凝土柱進行了軸壓試驗研究，並對19根加固鋼筋混凝土柱和4根對比鋼筋混凝土柱進行了剪壓試驗研究；通過對試件荷載-應變曲線、荷載-撓度曲線和滯回曲線等的研究表明，採用該加固方法能有效的約束柱子橫向變形，並對提高鋼筋混凝土柱的極限承載力和延性有明顯的效果；同時根據理論及加固機理分析提出了適應於此加固方法的軸壓極限承載力計算公式。
  4. The paper gives a summary for the current technology situation of foreign and civil in the field on torsion and distortion of box gird bridges. by general bending theories, transfer matrix methods is used in the torsion and distortion of continues box gird bridges

    在分析變截面連續箱梁扭轉與畸變內力時所採用的方法是一種比較實用的計算方法即傳遞矩陣法，研究任意變截面連續箱梁的扭轉、畸變及橫向撓曲。
分享友人
分享到 Line

分享到臉書