止口 的英文怎麼說
中文拼音 [zhǐkǒu]
止口
英文
front edge-
Facing leans out from front edge
前襟止口反吐Split at front edge
止口下部搭疊過多Front edge is out of square
止口反翹Front edge is upturned
止口反吐Front edge is uneven
止口縮角Some bacteria protect against halitosis, the formal name for really bad breath, while others cause the pungent odor, says a team of researchers from the forsyth institute in boston
來自波士頓福塞斯研究所的一個研究小組發現,口腔內有一些細菌可以防止口臭,也就是口腔異味的產生,而另一些的作用則剛好相反。Supporting upstairs. change your bad customs in you life. first, you should rinse your mouth after having meal, this is very important. following don ' t forget brush your teeth when you get up and go to bed. remember
看看有沒有蛀牙,如果沒有就看看胃好不好.一般都是這兩方面引起的.現在有一種藥叫"口苦口臭一把抓" ,外用有口泰,還可以防止口腔潰瘍的哦Bust dart seam allowance must be ironed upward
胸折止口要燙向上面。Measure coaxiality of tow holes with three - coordinates machine
利用三座標測量機測量止口孔的同軸度Development of new conveyor idlers in no need of processing tube ends for installing bearings
新型免加工止口托輥的研製Front cut point
止口圓角點線5 tape extensions at the top must be securely enclosed in the facing or waistband … … … … no raw edges showing
"拉鏈帶" "頂部多出的止口應藏入腰頭貼內,不能外露。7 raw edge at hem on knit garments must be covered by twin needle cover - stitch, and must not be exposed
對于針織袖口、褲腳或衣腳,其"雙針綱底"縫線必須完全蓋過止口。1tc series boring and facing head is besed on 1ta series boring head with special cutter disc and cutter driving devicees, it not only functions of 1ta series boring head, but also can complete endface, external, splling and corner cutting
1tc系列鏜孔車端面動力頭是在1ta系列鏜削頭基礎上配置專用刀盤及進刀裝置而成,除具備鏜削頭的鏜孔功能外,還可完成車端面、車外圓、車止口、切槽、倒角等加工工序。1tc series boring and facing head is based on 1ta series boring head with special cutter disc and cutter driving devicees, it not only functions of 1ta series boring head, but also can complete endface, external, splling and corner cutting
1tc系列鏜孔車端面動力頭是在1ta系列鏜削頭基礎上配置專用刀盤及進刀裝置而成,除具備鏜削頭的鏜孔功能外,還可完成車端面、車外圓、車止口、切槽、倒角等加工工序。Mayo experts offer these tips to help prevent it
梅奧門診的專家們提出以下幾種防止口臭的方法。Problem. mayo experts offer these tips to help prevent it
梅奧門診的專家們提出以下幾種防止口臭的方法。Pay attn. the workmanship of ironing, don ’ t press the seam too much and avoid the seam allowance see through by heavy pressing
注意燙工,骨位不要燙太重,避免縫骨止口起痕。7 zippers tape tail must be secured with back tack to the seam allowance …. this applies to both lap style and invisible zippers
對于某些"隱藏拉鏈款式"或"外露拉鏈款式" ,其拉鏈帶尾端須與衣身的止口用平車縫合。It can not only manufacture die holders of various standards for customers, but also non - standard holders according to their drawings. the processing includes precise frames, water - carrying holes, angle holes, thimbles, front edges, and 3 - d forming dies
不僅?客戶製作各種標準模架,還可根據客戶的來圖要求,製作各種非標模架,加工范圍包括精框精框,運水孔加工斜孔頂針止口及三維成型模具加工等。分享友人