正反面接線 的英文怎麼說

中文拼音 [zhēngfǎnmiànjiēxiàn]
正反面接線 英文
front back connection
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 反 : Ⅰ名詞1 （方向相背） reverse side 2 （造反） rebellion 3 （指反革命、反動派） counterrevolutionari...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 接線 : 1 [電學] （連接導線） wiring2 （電話員接通線路） work a telephone switchboard; connection接線插座...
  1. In order to solve the problems of which the spiral bevel gear of oerlikon type is necessary to out and modify repeatedly, a new method was developed to predict the contact pattern and greatly reduce the cost for manufacturing by means of building a tooth contact analysis model of prolate epicycloids bevel and hypoid gears for oerlikon skm2

    摘要為解決奧利康錐齒輪加工過程中需要反復試切、修正的問題，根據奧利康skm2機床建立了加工延伸外擺線齒錐齒輪和準雙曲面齒輪的齒面接觸分析模型，提出了一種可預測齒面接觸質量、降低設計加工成本的新方法。
  2. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  3. Some people thought the regular education should not be changed because it is a matter of fundamental importance for generations to come. on the contrary, some thought the regular education system would let a nation perish and it was necessary to turn middle schools and universities into short - term training courses that would produce qualified personnel for both the front and the rear. in others " opinion, the whole educational system should be arranged, enriched, adjusted, improved, and expanded, meanwhile, some facilities matching the war should be increased

    一些人認為教育是百年大計，不應更改；另一些人的主張與此完全相反，他們認為維持正常教育就是在堅持「亡國教育」 ，大中學校應全面轉軌，變成各種戰時短期培訓班，直接為前線後方輸送抗戰人才；也有人主張一面對整個教育事業加以整理、充實、調整、改進、擴充，一面增加一些適應抗戰需要的設施。
  4. Through the excel program, and combining the inside and outside environment of the excavation and stress field and displace field, the data of stress and displacement of points are analyzed in variable depth and load grade and terminal state. the spss software has been applied to the statistics of geometry parameter of failure surface, and the failure surface criterion is created by the linearity regression from d ( the longest horizontal distance between the failure surface and the side face of the slope ), ho ( the depth

    此外，應用spss軟體對試驗破壞滑弧的幾何參數進行統計分析，並對滑弧的最大水平深入距離d及d處至坑底的高度h _ 0結合各水理指標進行多元線性回歸，建立滑面的判據，並對此判據進行修正，且用實際工程對其進行評價，通過反算已知滑面的c 、值，表明邊界條件對破壞形式有極大的干擾作用，所直接看到的破壞類型土體不是發生整體滑移破壞，而是剝落式的潰屈破壞。
分享友人
分享到 Line

分享到臉書