正弦調制 的英文怎麼說

中文拼音 [zhēngxiándiàozhì]
正弦調制 英文
sinusoidal angular modulation
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  1. Digital pwm techniques for sine inverter power

    正弦逆變電源的數字脈寬調制技術
  2. This thesis introduces the base theory and correlative information of variable frequency speed variation, and expatiates sinusoidal pulse width modulation ( spwm ). the principle of svpwm is in - depth discussed, and a simple algorithm for svpwm is ratiocinated

    本文介紹了交流變頻調速的發展概況，分析了其基本原理，闡述了正弦脈寬調制（ spwm ）原理，對svpwm理論進行了研究，給出了svpwm的簡單實現演算法。
  3. Moreover, it does not necessarily need waveforms other than sinusoids, for both modulator and carrier, in order to produce interesting musical sounds

    而且，它不一定需要調制器和載波波形（除了正弦波）來創作有趣的樂聲
  4. 1 m 0. 5, the phase - shifted angle 6 is controlled in term of sine law which makes the magnitude of resonant voltage track a reference sine voltage, and the resonant voltage is rectified, filtered, inverted and then the better sine - voltage output is obtained, theoretical analysis and experimental results show that for the resistive load and inductive load, the switches of leading leg of the phase - shift - controlled circuit are always turned on at zvs, and ones of lagging leg are turned on at zvs ( < 0 ) or turned off at zcs ( ( > 0 ), moreover, all switches in the low - frequency inverter are always turned on and off at zvs, the measured circuit efficiency for rated load reaches up to 88 %

    從功率單向流動角度出發，提出了一種lcc諧振型恆頻移相單相高頻鏈逆變電路拓撲，在調制系數0 . 1 m 0 . 5情況下，控制移相角按正弦規律變化，使諧振電壓脈沖列的幅值追蹤參考正弦電壓信號，經過整流、濾波、低頻逆變，從而獲得正弦度較好的輸出電壓。理論分析和實驗結果證明對于阻性負載或阻感性負載，移相全橋具有超前橋臂零電壓開通，滯后橋臂或者零電壓開通（ _ 0 ）或者零電流關斷（ _ 0 ）的軟開關特性，而低頻逆變器的各個開關均實現零電壓條件下的開通與關斷。
  5. Voltage segment network constituted by electron switch of bta and controlled by single chip microcomputer constitutes a new fast electronic regulator. for bta cross zero touch off, sine wave which is exported is integrity. a new way to generate stable ac current is found with feed back control system by single chip microcomputer. so a new high power ac current regulator is developed

    採用單片機控制雙向可控硅作為電子開關所組成的電壓分節網路，組成新穎快速的電子調壓器；由於雙向可控硅過零觸發，所以其輸出是不失真的完整正弦波；再用單片機組成反饋控制系統，從而找到了交流穩流的新方法，研製出一個大功率交流穩流電源
  6. Abstract : voltage segment network constituted by electron switch of bta and controlled by single chip microcomputer constitutes a new fast electronic regulator. for bta cross zero touch off, sine wave which is exported is integrity. a new way to generate stable ac current is found with feed back control system by single chip microcomputer. so a new high power ac current regulator is developed

    文摘:採用單片機控制雙向可控硅作為電子開關所組成的電壓分節網路，組成新穎快速的電子調壓器；由於雙向可控硅過零觸發，所以其輸出是不失真的完整正弦波；再用單片機組成反饋控制系統，從而找到了交流穩流的新方法，研製出一個大功率交流穩流電源
  7. During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied

    在溫度場的模擬中，模擬結果表明，保壓時間是影響製件成形質量的關鍵因素之一，擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大，需進行參數之間的協調，只有當變形區內部始終維持準固態時，才能實現穩定的液-固擠壓成形過程；在變形場的模擬中，根據液態浸滲擠壓的成形特徵，選用了雙曲正弦剛-粘塑性有限元計算模型，研究了變形過程中應力應變場的變化規律，研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。
  8. There are five parts are as follows : in part one, the concept of switching function is introduced first to establish the nonlinear mathematical model of the induction motor variable frequency speed adjustment system which is fed by a sine pulse width modulated ( spwm ) inverter and takes the effect of the main magnetic circuit saturation into consideration, then the low frequency oscillation of the system is simulated according to the model. next, from the view point of energy conversion of the inverter - induction system, a criterion for the low frequency oscillation is proposed to determine whether the system is in low frequency oscillation which is judged by whether the interval of the negative current component of the inverter input current is more than 1 / fc ( fc is the carrier wave frequency of the inverter ) or not

    首先引入開關函數概念，建立了正弦脈寬調制（ spwm ）逆變器供電異步電動機，考慮主磁路飽和時的變頻調速系統整體數學模型，模擬系統的低頻振蕩；其次從逆變器-異步電動機系統能量轉換角度出發，提出通過檢測逆變器輸入電流中負電流的間隔時間是否大於1 / f _ c （ f _ c為逆變器載波頻率）來判定系統是否出現低頻振蕩；最後的實驗結果驗證了系統低頻振蕩建模和判據的實用性和正確性。
  9. ( 4 ) periodicity and pseudo - modulation when sampling sinusoidal signals the periodicity and pseudo - modulation due to non - integral sampling of sinusoidal signal are analyzed

    著重討論連續信號采樣過程中抽樣定理對正弦信號的非整數抽樣序列的周期性，偽調制性和調制周期的周期性。
  10. The main circuit is consisted of 18 thyristors circuit and protection circuit. with the help of control subsystem, it can get the output of low frequency voltage ( current ) with the shape of sine wave ; the core of the control subsystem is the cpu of 87c196kc, and the synchronization circuit, the pulse - widen circuit, and the power - enlarged circuit form the accessorial subsystem of the control system. it possesses all the functions of digital triggering, digital tuning, analog / digital conversion ; the input transfer can isolate the input and output ; and the circumfluence reactor can reduce the circumfluence

    主迴路採用由18個晶閘管組成的三相零式電路，並輔以晶閘管的保護電路，通過控制可以得到低頻正弦波的電壓（電流）輸出；控制迴路主要以87c196kccpu為核心，其外圍電路包括同步電路，脈沖拓寬電路，功率放大驅動電路等，完成了數字觸發、數字調節、模數轉換等功能；進線電源變壓器具有變壓和隔離作用；環流電抗器則實現了有效抑制主迴路瞬時脈動環流的功能。
  11. 3 using current injecting frequency modulation method and modulating sine wave around the resonator point, the lock - in phenomena is observed in a comparatively short period of time. this has achieved the basic goal for a closed loop r - fog

    3 、採用電流注入法，在諧振點附近進行正弦調制，實現了對諧振點的短時間鎖定，達到了閉環光纖陀螺設計的首要基本要求。
  12. Firstly, according to the detailed analysis on the mathematical model of pmsm, the principle of field oriented control ( foc ) is illustrated. spwm and svpwm are analyzed and contrasted in detail too, and the digital realization techniques based on dsp are given

    本文首先在分析永磁同步電機數學模型的基礎上，闡述了永磁同步電機矢量控制基本原理；對正弦波調制技術（ spwm ）和空間矢量調制技術（ svpwm ）兩種脈寬調制策略進行了詳細的分析和對比研究，給出了基於dsp的數字化實現方法。
  13. Continuous single tune jamming is an effective jamming to linear frequency - modulated radar. however it can not suppress signal output after being full of the sidelobe suppress filter of the jammed bi - phase coded radar, no matter how great the power of it may be

    單頻正弦波干擾對線性調頻雷達是一種有效干擾，但對於二相編碼雷達無論具有多大的功率在充滿二相編碼雷達接收機的旁瓣抑制濾波器后也不能壓制信號主瓣，因此是一種無效干擾。
  14. The system can generate three - phase spwm pulses and has following characters : the range of modulation frequency is from 0 khz to 4 khz. and can be divided to 7 classes to control. the carrier frequency may be selected up to 24 khz, and can be divided to 8 classes to control ; rotational frequency is defined to 16 bits

    該系統能產生三相六路正弦脈寬調制（ spwm ）波形;調制頻率范圍為0 4khz ，分7級控制; 16位的速度控制解析度;載波頻率分8級控制，最高可達24khz ;系統介面兼容intel系列和motorola系列單片機;該系統控制簡單、精確，易修改，可現場編程;同時具有脈沖延時小、最小脈沖刪除、過壓和過流保護功能等特點，可應用於pwm變頻調速系統的全數字化控制。
  15. In this paper, a simple and practical circuit for laser diode modulation is presented, the principle circuit and the principle of choosing component are given, at last, application in sine wave modulation in non - cooperative target phase shift laser rangefinder is introduced

    本文介紹了一種簡單有效的半導體激光器調制電路，給出了電路原理圖，元件的選擇原則，最後介紹了在非合作目標相位式激光測距系統中實現正弦調制的應用。
  16. A system with repmsm ( rare earth permanent magnet synchro - nous motor ) as executing motor is presented in this thesis. the hardware platform for the ac speed regulating system is based on tms320f240 dsp controller and uses ipm ( intelligent power model ) as the power device in the invert circuit

    系統選用正弦波永磁同步電動機為執行電機，以ti公司的tms320f240dsp晶元為控制核心，以智能功率模塊（ ipm ）為逆變電路功率開關器件，構成交流調速系統的硬體平臺。
  17. The system uses the permanent magnet synchronous machine as the driver motor based on the idea of polygonal flux linkage locus and the permanent magnet brush - less motor is as the momentum balance motor by means of speed and current loop in order to track driver motor precisely and rapidly. the harmonious control of driver motor and balance motor is realized by making full use of the dsp hardware resource and complicated programmable logic device. the software design is composed of c and assembly language to realize motor control arithmetic of polygonal flux linkage locus

    衛星天線伺服控制系統以正弦波永磁同步電機作為驅動電機，採用多邊形磁鏈軌跡法（電壓空間矢量法）的控制策略；動量平衡電機採用永磁無刷直流電機，通過電流環、速度環達到快速、精確跟蹤驅動電機的目的，確保了衛星姿態恆定；設計方案中充分利用了dsp硬體資源和復雜邏輯陣列實現了驅動電機和平衡電機的協調控制，並通過c語言和匯編語言的混合編程實現了電機的多邊形磁鏈軌跡控制演算法。
  18. The three - phase spwm pulses are generated through sine wave compared with triangular wave. during design, we make use of a changed structure of nco ( numerically controlled oscillator ) to

    數字化設計是本系統的特點，系統最終生成的三相spwm脈沖是基於三相正弦調制波和三角載波比較得到的。
  19. A linearization method to design biorthogonal cosine modulation ( bcm ) filter banks is proposed

    摘要介紹了一種用於設計雙正交餘弦調制濾波器組的線性化方法。
  20. A design example is presented to demonstrate the validity of the proposed algorithm

    設計實例表明，該演算法對于雙正交餘弦調制濾波器組的設計是非常有效的。
分享友人
分享到 Line

分享到臉書