死區調節器 的英文怎麼說

中文拼音 [sǐqūdiàojiéqì]
死區調節器 英文
dead zone regulator
  • 死 : Ⅰ動詞（失去生命） die Ⅱ形容詞1 （不顧生命; 拚死） to the death 2 （達到極點） extremely; to death...
  • 區 : 區名詞（姓氏） a surname
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 節 : 節構詞成分。
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 調節器 : regulator; adjuster; governor; controller; conditioner; actuator; phaser
  • 調節 : regulate; adjust; monitor; measure; take care of; condition; regulation; adjustment; conditioning...
  1. The core instrument for frequency - following is the pll. the dsp is used to realize the regulating of the dead time on - line

    用鎖相環作為頻率跟蹤的核心器件，根據最佳死區的理論，用dsp實現死區的在線調節。
  2. Firstly. operation principle of induction heating is introduced and the actuality of the power supply for induction heating is summarized. then, the scheme of structure of the power supply is established : uncontrolled rectifier and buck chopper constitute dc circuit. in this part, operation principle of a kind of soft switching buck chopper is presented mainly and the conclusion that the power semiconductor devices operate in soft switching is also illustrated by analysing the operation principle of all stages ; series resonant inverter is selected as inverter circuit via comparing the advantage and shortcoming of parallel resonant and series resonant. moreover. the work principle of series resonant inverter is analysed and the calculating method of the best dead time is put forward as well

    文中首先介紹了感應加熱電源的工作原理並綜述了國內外的研究現狀。接下來分析並制定了電源主電路的構成方案：在對比幾種功率調節方式的基礎上選擇了不控整流加斬波調壓作為直流部分。在這部分里，重點研究了一種軟開關buck變換器，通過分析各階段的工作原理說明了開關器件如何工作在軟開關狀態；對于逆變器部分，在比較了串、並聯逆變器優缺點的基礎上選擇了串聯諧振逆變器，並詳細分析了串聯逆變器的工作原理，提出了最佳死區的計算方法。
  3. In the digital inverter, we adopt the technology of digital dynamic waveform correction, which can compensate the delay between control signal and output waveform, and ensure the accuracy of control. at the same time, the technology of digital dc component adjustment was introduced, by which we can exactly compensate the control signal, and realize adjusting dc component of output on the premise of output performance

    在基於dsp的數字變換器平臺中，採用全數字波形校正技術，完全補償了控制信號延時、功率管開關延時以及死區時間對輸出spwm波形所產生的畸變，充分保障了變換器控制的準確性；採用數字直流分量調節技術，可以精確地對控制信號進行補償，在充分保證輸出性能的前提下，實現了輸出直流分量的調節。
  4. Finally, the rules used to design the induction motor and set the inverter v / f curve are summarized to improve the stability of the system movement in the forth part of the dissertation, three measures are brought forward to eliminate the system low frequency oscillation. the first measure adopts pulse based dead time compensation to suppress the oscillation. as second measure, considering the motor and inverter as an integration, the discontinuous space vector modulated strategy named dpwm3 is proposed for the first time to suppress the oscillation

    措施一是在總結常用死區補償方法的基礎上，提出脈沖為基礎的死區時間補償法（ pbdtc ）對死沈陽工業大學博士學位論文區進行補償，抑制系統的低頻振蕩;措施二是從逆變器與電機的機電一體化配合更加完善的角度，首次提出採用不連續空間矢量調制策略dpwm抑制系統的低頻振蕩;措施三是通過對系統中電機參數的調節，達到抑制系統低頻振蕩的目的;最後進行了實驗驗證。
  5. In the realization of the inverter control circuit, the signal from the pll is input to ir2110 via adjusting phase and forming dead time. sg3525 is selected as the core device of the chopper. meanwhile. two pulse that will input to the chopper can be obtained by simple design. besides. the circuit of which core chip is dsp is described

    在逆變控制電路的具體實現中，用鎖相環作為頻率跟蹤的核心器件，經相位調整、死區形成等環節得到兩路觸發信號，輸入到ir2110中即可作為逆變器的驅動信號。
分享友人
分享到 Line

分享到臉書