氣動執行器件 的英文怎麼說

中文拼音 [qìdòngzhíhángqìjiàn]
氣動執行器件 英文
air activator
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 執 : Ⅰ動詞1 （拿著） hold 2 （執掌） take charge of; control; manage; wield 3 （堅持） persist in; sti...
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  1. First, it is compressible and cushiony ; second, it can be transported to a long distance with a little power loss ; the last, its flux and velocity of flow are quite high, so the reaction time of the operators can been considerably shortened. aiming to solve the problems of vibrating machinery such as short life - span, poor cushion and high energy consumption, the writer, on the basis of characteristic of pneumatic mentioned, contrives a set of valve controlled pneumatic vibrator, which has larger output vibrating force and longer life - span with simple structure. then, it is applied to drive a vibrating screen and the result is fairly well

    文中針對氣動技術本身的特性及優點，如：可壓縮，具有緩沖性；能耗損失小，便於遠距離輸送；流量大、流速高，執行元件響應速度快等，以解決振動機械在應用過程中的緩沖、能耗以及使用壽命等問題為目的，設計出一套輸出激振力大、結構簡單、使用可靠的閥控氣動激振器，並將其成功地運用到振動篩上，取得了較好的效果。
  2. After the introduction of the selected elements, the thesis gives out a design which includes a front control center based on siemens s7300 plc 、 a line connection of the master profibus and the distributed intelligent i / o et200m system 、 a real - time display system of pressure sensors and a gas supply system with stop valve and electric actuator

    本文在介紹了所選擇器件情況基礎上，設計了基於siemenss7300plc為前端控制中心，利用profibus總線接分散式智能i / o et200m系統，壓力傳感器現場顯示，截止閥加電動執行器實現配氣的方案。
  3. Based on remaining the dismantling and loading, we make full of the equipped instrument, and fall the whole cycle into three modules : speed - adjusting module, pressure module and multi - execution instrument module. we must compile the related plc control program and pc control program, and redesign the control cabinet and re - fix the electric cycle. we complete the auto - control of the hydraulic experiment table through the loading and recapitulate debugging

    在保留其元件可裝拆性的基礎上，我們充分利用現有液壓實驗臺的液壓元件，對其基本迴路進行重新組合，分為調速、壓力和多執行元件控制迴路三個模塊，並編制可編程式控制制器程序和上位機數據採集程序控制迴路動作，重新設計該實驗臺的電氣控制櫃，並進行現場接線和安裝調試，實現所有教學必須實驗迴路的自動控制。
  4. Elimination of bracket or connection adopter for directly fitting offers easy and correct installation. please contact us for installation of spring return pneumatic actuators

    直接安裝可避免不必要的連接支架或連接套件，便於現場安裝及減少安裝偏心誤差。安裝彈簧復位式（單作用）氣動執行器請及時和我們聯系。
  5. Analysis of common failures occurred in engines with electronically controlled fuel injection system is carried out from six aspects : ecu, sensor, acuator, connection, air and fuel lines, as well as air and fuel filters

    從ecu常見故障，傳感器故障，執行器故障，插接件（或連接導線）連接故障，連接管道松脫故障，空氣、燃油濾清器堵塞故障6個方面宏觀分析電噴發動機的常見故障並舉例分析。
  6. The article put forward the general plan to realize intelligent pneumatic actuator and studied and analyzed on some of key technical questions : low power - consumption electrical - pneumatic converting unit and low power - consumption control circuit solution which is based on piezo ceramic principle and meet the requirements of intrinsically safe explosion - proof ( ib ct5 ) ; general software solution which realizes the goal of intelligence and hart communication function ; reliability design solution which answers the purpose of mtbf 16000 hours and regard electrocircuit, machine unit and software as main parts

    本課題以氣動調節閥的智能化為研究目標，提出了實現氣動執行器智能化的總體方案。並對其中幾個關鍵技術難題進行了研究分析：以滿足本安型防爆要求（ ib ct5 ）的基於壓電陶瓷原理的電氣（ i / p ）轉換單元、低功耗的控制電路方案；以實現智能化和hart網路通訊功能為目標軟體總體設計方案；以mtbf 16000小時為目標和以電子電路、機械零部件、軟體為主體的整機可靠性設計方案。
  7. This equipment is for general assembly of clutch pressure plate assembly and calibration of diaphragm finger ; the whole machine is driven by compressed air and air cylinder is controlled by electromagnetic valve by finishing multiple functions ; this equipment divides into two basic types for light - duty and heavy - duty, it also can be made into light & heavy duty equipment according to user ' s request

    本設備用於汽車離合器壓盤總成的總裝和膜片分離指的校正；設備動力用壓縮空氣，執行元件用電磁閥控制氣缸以完成多項功能；本設備分輕型及重型兩種基本型號，也可按照用戶要求，將輕型與重型做成雙工位設備。
分享友人
分享到 Line

分享到臉書