氣壓固結 的英文怎麼說

中文拼音 [qìyāgùjiē]
氣壓固結 英文
gas pressure consolidation
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 壓 : 壓構詞成分。
  • 固 : Ⅰ形容詞（結實; 牢固; 堅硬） firm; hard; solid Ⅱ副詞1 （堅決地; 堅定地） firmly; resolutely 2 [書...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 氣壓 : [氣象學] pressure; atmospheric pressure; barometric pressure; gas pressure; air pressure
  1. By comparing the dry plate pressures drop and distributions of velocities simulated on single valve with those of double valves, it was found that there was intense turbulence in the flow fields around fixed - valve, there were eddy areas between valve side orifices and tray wall, there were eddies above the valves too, these led to the complex behaviors of gas perforating valve, these had a great effect on the gas - liquid mass transfer process. at the same time, in order to prevent the disadvantageous effect of gas between one valve with another on the gas - liquid mass transfer, it was very effective to change the fields of gas perforating valve by folding the edges of valve

    通過對數值模擬得出的單閥和雙閥塔板的干板壓降及流場速度分佈分析對比后發現，固定閥周圍流場存在較強的湍動，閥側孔與塔板壁面區域以及閥體的上方空間存在明顯的渦流區，使氣體穿閥后的行為變得復雜，並對氣液傳質過程產生重大影響；模擬結果表明，為防止和削弱固定閥間的對沖造成的「死區」對傳質帶來的不利影響，通過折邊來改變氣體的氣路是非常有效的，模擬值與實驗值基本得到吻合。
  2. In this thesis, flow regime identification and malfunction diagnosis of fluidization were studied with fractal technology, the presented methods for both flow regime identification and malfunction diagnosis were proved of effectivity. main achievements are as following : 1. fractal brownian motion ( fbm ) was made from gauss noise and compared with pressure fluctuation signal of gas - solid fluidization, which demonstrated the similarity between the fbm and the signal

    在通過fbm （分數布朗運動）數據模擬證明了氣固流化床壓力波動信號與分數布朗運動是相似的基礎上，提出了用分數布朗運動來模擬氣固流化床壓力波動信號，並採用r s分析法從信號時間序列中提取出hurst指數，通過分析信號hurst指數值對流化床流型和結塊故障進行了研究。
  3. The investigation of a lot of parameters about treated sandstone, brick materials and earthen materials with fluorited polymers has been carried out, such as the formation of polymer, the penetration depth, porosity, capillary absorption and penetration coefficient, water uptake, compressive strength, drilling resistance, absorption isotherms of water vapor, water vapor diffusion, color changes as well as resistance to desegregation of water, frizzing - throwing cycles, worming - cooling cycles, and so on. in addition, the influence of salt crystallization, acid and base, and uv aging have also been assessed in order to better understand the protection effects and utilization possibility of two fluorinated polymers, mainly according to astm standard and the combination of international methods together with general technological

    分別以國家級文物保護單位的土質、砂巖和磚材文物樣品為對象，依據astm標準及國際通用文物保護研究方法與評估準則相結合，通過膠化物形成周期、滲透深度、孔隙度、毛細吸水和滲透系數、持水量、抗壓強度、抗鉆強度、吸附水蒸氣的能力、透氣性、外觀顏色等系列參數的測定，及凍融、冷熱循環、酸堿腐蝕后抗壓強度的衰減、可溶鹽對保護效果的影響、酸堿及光照對表面保護效果的影響，對兩種含氟聚合物及其與有機硅的共混物在文物加固保護和表面防護中的可行性和保護效果給予了系統研究。
  4. The characteristics of high pressure gyratory sprayed pumping discusses is presented, which is applicable in wide range of scope and ground layers, convenient for construction, long durability, wide source of materials. mechanism for subgrade strengthening : complex foundation of cement solid and earth between piles was formed by pulsant load of flowing pressure and spraying flow, water wallop, cavitation phenomenon, water wedge effect, extrusion force and air flow agitation etc so as to enhance foundation bearing force and reduce settlement and deformation

    高壓旋噴注漿技術具有適用范圍、適用地層較廣，施工方便，耐久性好，材料廣闊等特點；其加固地基機理主要是通過流動壓、噴射流的脈動負荷、水塊的沖擊力、空穴現象、水楔效應、擠壓力、氣流攪動等效應形成水泥固結體與樁間土的復合地基，從而提高地基承載力，減少沉降變形。
  5. One was based on the sbs sensitive membrane and " gas phase " immunoassay technology. by immobilized anti - tb or anti - trichinosis on the sbs membrane, it can be used to determine m. tuberculosis and trfohiflosjs. the other one was based on the protein a sensitive membrane and " liquid phase " immunoassay technoiogy

    一種是基於sbs膜固定抗體的壓電氣相兔疫技術，我們利用該技術首次對結核病和旋毛蟲病分別進行了快速診斷：另一種是基於蛋白a定向修飾抗體的壓電液相兔疫傳感技術，我們利用該技術首次對結核病進行了診斷。
  6. Some research results are achieved as follows : ( 1 ) layout of lpg supply system and modification of body construction are carried out, and structural analyses of fuel supply bracket are performed. then fuel bottle with single - welding line and valve type specially used for lpg motorcycle is designed and fabricated, and boil - off pressure adjuster and mixing unit of lpg fuel supply are successfully developed

    主要工作和結論如下： （ 1 ）完成了lpg摩托車燃料供給系的總體布置與整車改裝，及其燃料供給系支架與座墊支承的結構分析和抗彎加固；設計和製造加工出組合閥式、單焊縫結構的lpg摩托車專用鋼瓶；實現汽化調壓器與混合器的良好匹配及長縫式等比例式空氣與燃氣混合器的成功開發。
  7. The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine

    用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。
  8. In this paper, high heat penetration into a moving particulate bed is described mathematically with a comprehensive heat and mass transfer model. the distribution of gas velocity and pressure, the temperature field of gas and solid in the moving particulate bed are examined for different conditions. the results show that thermal penetration into the moving packed - bed particles by fluid flow in porous media is high only in the position near the gas entrance. the thermal penetration thickness tends to increase with the fluid flow velocity and decrease with the particle moving velocity. in the region of thermal penetration, the porosity of solid bed has significant effect on gas field and pressure loss. it is feasible to reduce the gas pressure loss by a larger width / height packed bed in design and operation. the correspondence between thermal infection depth and particle bed height would be helpful to keep high oapacity of reactor and reduce the cost of operation

    針對移動顆粒床中物料層內的高溫氣體滲流傳熱現象，考慮滲流與傳熱的相互作用，採用局部非熱平衡假設建立了多孔介質滲流傳熱物理數學模型並進行了數值計算.研究了不同情況下床內填充多孔介質中的流速、氣固溫度和床層壓力損失.計算結果表明，高溫熱氣對移動床顆粒料層的熱滲透主要發生在滲流入口端區域，增大入口滲流速度以及減小床層物料下移速度將導致物料溫度沿床高慢速下降，熱滲透深度擴大，熱滲透作用區域內的物料溫度水平提高.在熱滲透作用區域，孔隙率對流場和壓力損失有很大的影響.研究結果對于移動顆粒床反應器的設計與運行具有一定的參考作用
  9. The " green " bricks are then treated in an autoclave under steam pressure forming hydrated calcium silicate bonding the aggregate particles into a strong and durable brick

    然後該綠色磚在一個高壓鍋的蒸汽壓力下進行處理，形成水化硅酸鈣再結合聚合物顆粒的堅固耐用的磚塊多孔磚和加氣
  10. On the other hand, through inhibted performances of concrete and mortar, the permeability refutations with different w / c, ages, admixture, and physics chemistry absorb regulation of different viscosity permeable liquid, the liquid - gas method is proved science and accuracy. because adopting with liquid - gas method it case clearer concrete permeability regulation. different concretes relativity is more exact and more efficiency and fixed quantity

    另一方面，我們利用混凝土所固有的性質：不同水灰比混凝土、砂漿、抗滲性能規律；不同齡期混凝土的抗滲規律；不同外加劑、摻合料抗滲性能之間相互對比規律；不同黏度滲透液物理化學吸附對測試結果影響的規律；用規律來映證溶液氣壓法的科學性，準確性。
  11. Temperature kits : contact must be properly fixed in the evaporator export pipelines, real - time communication evaporator components to temperature degrees, the material will be filled through interlinked capillary pressure due to the expansion of corrugated boxes ; swelling corrugated boxes on the pressure for change in the thrust pole with an adjustment screw and spring - loaded ball - type valves to adjust the resistance of the degrees of refrigeration volume precision adjustments

    感溫包：是必須妥善接觸固定在蒸發器的出口管道上，感知蒸發器實時回氣溫度的部件，它將充填物質的熱脹冷縮壓力通過相通的毛細管提供給膨脹波紋箱；膨脹波紋箱依據壓力的變化推動推力桿結合過熱度調整螺絲和彈簧的阻力來調整球型閥的開度，實現製冷量的精確調整。
  12. Abstract : according to the characteristics of solid - liquid two - phase flow, the equation of motion and the equation of continuity for hammer computation are deduced in this paper. the equations are applied to analyze the effect of different prevention deveces used to relieve water hammer pressure in pipeline transport with displacement pumps. it is concluded that the air vessel and pressure relief valve are better than other devices

    文摘:本文針對固液兩相流的特點，建立了水擊計算的運動方程及連續方程，並採用新方程對礦山常採用的容積泵輸送中使用的儲氣罐、泄壓閥、緩閉逆止閥等減緩水擊壓力的防護措施進行了計算分析，得出儲氣罐、泄壓閥減壓效果最好的結論。
  13. An interpolation program is used to convert the fluent result data to the ansys load data. it is a new method to analyze turbine tip clearance. in this paper, some research of the numerical computation of the tip clearance of aero - engine is done, the parametric method is used and the research on the flow, heat and structure integration analyses is accomplished

    本文對渦輪機匣氣熱固一體化分析方法做了研究，通過編制了載荷轉換與施加程序，從氣熱計算模型中提取溫度場計算結果，並作為載荷加入到熱固耦合計算模型中，實現了高壓渦輪機匣的一體化計算分析，為實現渦輪葉尖間隙的氣熱固一體化分析打下了基礎。
  14. First, the working principles of the combustion control system of marine main boiler in present use and its disadvantages are discussed in the paper ; in the light of the structure and motion traits of marine main boiler, the combustion control systems of single and double cross amplitude limits are designed. at the same time, the schematic diagram of system and recovery curves of some relative parameters are given, the system working principles and its advantages and disadvantages are discussed. based on the combustion control system of dual - crisscross amplitude limit, by selecting the independent variable, the fixed offset is improved into variable offset, the combustion control system of variable offset dual - crisscross amplitude limit is designed

    首先討論了目前船用主鍋爐燃燒控制系統的工作原理及存在的不足；針對船用主鍋爐的結構及運行特點，設計了單交叉限幅燃燒控制系統和雙交叉限幅燃燒控制系統，同時給出了系統原理圖及有關參數的過渡過程曲線，討論了系統工作原理及優缺點；在雙交叉限幅燃燒控制系統的基礎上，將固定偏置經過自變量的選取，改進成變偏置，設計了變偏置雙交叉限幅燃燒控制系統，給出了系統原理圖及有關參數的過渡過程曲線，同時也給出了空氣壓力和燃油流量正負偏置函數與變偏置折線函數的關系式。
  15. Then, the idea of integrating the standard configurable modules to building the basic model universal ats is brought forward, and the basic model universal ats fitting the rocket engine ground test is built by using the scheme of “ vxi ( or pxi ) and plc ”

    將基本型通用ats應用到不同類型的固體火箭發動機、燃氣發生器和壓力恢復系統地面試驗中。經過近千次試驗考核，系統滿足試驗需求，達到了預期設計目標。試驗驗證了開放式柔性ats體系結構的合理性和基本型通用ats設計的可行性。
  16. The pore air pressure gradually goes up with the developing of axial strain in the process of the dynamic torsional shear test of loess, but the pore water pressure hold the line or goes up a little in the last. the stress - strain dynamic constitutive relationship of intact loess and man - made loess show the hyperbolic model. there are some remarkable differences of strength and strain between unsaturated loess and saturated loess

    研究結果表明：非飽和黃土在動力扭剪試驗過程中，隨著軸向變形的發展，孔隙氣壓力逐漸上升，而孔隙水壓力則基本保持不變或後期略有升高；原狀黃土和重塑黃土的應力應變本構關系呈雙曲線型；非飽和黃土和飽和黃土的強度及變形特性存在明顯差異；進而分析了含水量、固結應力和固結應力比對黃土動力特性的影響本文最後對非飽和土的有效應力計算公式進行了討論。
  17. The model analysis of the deployed beams were studied in both theory way and simulation way. the differences of the beams in different pressures were studied. investigations showed that the method of modeling for short and long rolled beams is doable ; the process of fold maybe lead so large displacement and stress that membrane is damaged at local areas, ration and material wrinkle generates,

    研究結果表明:本文提出的分別針對短、長捲曲折疊充氣管的建模方法是有效的;在充氣管展開過程中，充氣速度越大，展開的速度越快，但由於阻尼損耗，二者並非線性關系;充氣速度過大不利於結構展開過程的穩定性;充氣支撐管的氣壓越大其固有頻率越高，但影響效果很小。
  18. The distribution of negative pore - water pressure, the action of atmosphere pressure and the restraint of deformation determined the consolidation status of vacuum consolidation

    抽真空作用下試樣的固結狀態與情況與試樣中負壓分佈、大氣壓的作用情況和變形約束條件等因素有關。
  19. In this paper, some aspects of vacuum preloading were studied as follows. vacuum consolidation test and load consolidation test were performed and compared for different kind of soil samples. after analyzing the results of tests, the four major mechanisms of vacuum consolidation were defined as : variation of capillary potential, drainage of sealed bubbles, vaporization and action of atmosphere pressure, in which, the action of atmosphere pressure is the most important factor

    首先對不同土樣進行了一系列室內真空固結和加載固結的對比試驗，通過對試驗結果的比較分析，明確了抽真空引起土樣固結的原因，即抽真空作用會在四個方面對試樣產生影響：毛細管勢的改變、封閉氣泡的排出、汽化現象及大氣壓的作用，而其中大氣壓的作用是最主要的。
  20. Being used the before - mentioned method, fold models of a column tube was established. by simulating analyses, effects of inflation velocity on the deployment process of different structures were investigated

    本文還分別從理論和模擬兩個角度對展開后，作為支撐結構的充氣管進行了模態分析，考察了不同充氣壓力對充氣支撐管的固有頻率的影響規律。
分享友人
分享到 Line

分享到臉書