氣泡狀流動 的英文怎麼說
中文拼音 [qìpāozhuàngliúdòng]
氣泡狀流動
英文
bubble flow- 氣 : Ⅰ名詞1 (氣體) gas 2 (空氣) air 3 (氣息) breath 4 (自然界冷熱陰晴等現象) weather 5 (氣味...
- 泡 : 泡Ⅰ名詞1 (氣泡) bubble 2 (像泡一樣的東西) sth shaped like a bubble Ⅱ動詞1 (較長時間地放在液...
- 狀 : Ⅰ名詞1 (形狀) form; shape 2 (情況) state; condition; situation; circumstances 3 (陳述事件或...
- 流 : Ⅰ動1 (液體移動; 流動) flow 2 (移動不定) drift; move; wander 3 (流傳; 傳播) spread 4 (向壞...
- 氣泡 : air bubble; bubble; bubble cell; pin hole
- 流動 : 1. (液體或氣體移動) flow; run; circulate 2. (經常變換位置) going from place to place; on the move; mobile
-
Image edge detection method for ert system of gas - liquid two - phase flow
水平井筒氣液兩相分散泡狀流流動模型According to dynamical characteristic of the bubble motion in the flow field, and under the assumptions of isothermal system without interior heat source, uniform bubble size, and ignoring surface tension, the mathematical expressions for interfacial momentum exchanges have been deduced which include drag, virtual mass force, and lift
針對氣液泡狀流中氣泡運動力學特性,在系統絕熱、無內熱源、忽略表面張力、氣泡尺寸均一前提下建立了氣液相間曳力、虛質量力、升力的數學模型表達式。The difficult-to-describe flow of gas, with its large deviations from plug flow and the bypassing of solids by bubbles, represents an inefficient contacting system.
氣體流動狀態難以描述,與活塞流離較大,由於氣泡產生而使固體顆粒發生溝流,這些都表示接觸效率降低。This paper analyzed the mechanism that gas and liquid flow through the holes according to the fluid characteristics of the compound tray, and put forward that there are three states of liquid flowing, gas flowing and blocked for the holes because of the foam fluctuating on the tray while the compound tray operates
本文根據復合塔板的氣液流動特點,分析了氣液穿孔流動的機理。根據前人的研究結果,提出復合塔板在操作時,由於泡沫層的波動,其篩孔存在通氣、通液和阻塞三種狀態。Another measure of holdup is the k factor used by bankoff in connection with the bubble flow pattern in gas-liquid flow.
滯留現象的另一個度量是Bankoff在氣-液流動的泡狀流型中所採用的因數K。Mushy pvc ( dop + additives ) - beater ( stir well ) - vacuuming ( materiel has been completely dewatered and debubbled after vacuuming ) or mix with color paste which has been processed by ball mill and then dropped into mould cavity by needle cylinder ) - solidified in the constant temperature box ( color fixing ) - input basic material - sent to the constant temperature box in the flowing way and then forming and then forming and sent out automatically - cooled by fan - finished products
糊狀pvc (增塑劑dop +助劑- - -打漿機攪拌均勻- - -抽真空處理) (真空機處理后的物料已完全脫離水分和氣泡)或球磨機處理后的色漿混合後用針筒滴入模具形腔- - -放入恆溫箱中固化(色彩定形) - - -注入底料- - -流水式送入恆溫機,定型后自動送出- - -風扇冷卻- - -成品The results demonstrate that the bubble velocity will increase with the increasing of the bubble volume, decreasing of resin viscosity and external pressure
此外,樹脂種類和樹脂流動狀態對氣泡的運動速度也有較大的影響。Another measure of holdup is the k factor used by bankoff in connection with the bubble flow pattern in gas - liquid flow
滯留現象的另一個度量是bankoff在氣-液流動的泡狀流型中所採用的因數k 。The experimental results show that the method is effective to identify the flow patterns of bubbly, plug, stratified, wavy, slug and annular in a horizontal pipe. the identification accuracy is shown as follows : bubbly flow is 93. 3 %, plug flow is 85. 3 %, stratified or wavy flow is 97. 3 %, slug flow is 98. 6 %, and annular flow is 92. 7 %. an estimation of the process time is 22 frame / s
實驗結果表明,該方法能自動有效地識別水平管道內的氣泡流、塞狀流、層狀流、波狀流、彈狀流和霧環狀流等基本流型;識別準確率如下:氣泡流為93 . 3 ,塞狀流為85 . 3 ,分層流為97 . 3 ,彈狀流為98 . 6 ,霧環狀流為92 . 7 ;識別圖像速度約為22幀秒,適合於在線實時識別兩相流流型。Thus, it is essential to know the movement behavior in resins in order to reduce voids and control porosity content effectively
本文藉助圖像跟蹤和數碼採集照相系統,研究了氣泡體積、樹脂粘度、外壓、樹脂種類和樹脂流動狀態對單個氣泡運動規律的影響。分享友人