氣門的 的英文怎麼說

中文拼音 [qìménde]
氣門的 英文
spiracular
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 門 : Ⅰ名詞1 （房屋、車船等的出入口 ） entrance; exit; door; gate 2 （形狀或作用像門的東西） switch; va...
  • 的 : 4次方是 The fourth power of 2 is direction
  1. Power assisted air gates - travel - way air locks - type doors with pressure

    動力輔助作動的空氣門.行車道空氣鎖.壓力門
  2. Air regulation systems in mining - wing air locks for travelling tracks - double - wing type doors with pressure reduction

    礦山空氣調節系統.車道用的側翼式空氣門.具有減壓平
  3. The two types of engine valves are intake and exhaust.

    發動機氣門的二種型式是：進氣口和排氣口。
  4. Reciprocating internal combustion engines - designation of the direction of rotation and of cylinders and valves in cylinder heads and definition of right - hand and left - hand in line engines and locations on an engine

    往復式內燃機旋轉方向氣缸和氣缸蓋上氣門的標志及直列式內燃機右機左機和發動機方位的定義
  5. The position of the valves during the power stroke are both closed.

    在作功沖程期間，氣門的位置都是關閉的。
  6. The spring is under compression, which means it tries to expand and thereby tries to keep the valve seated.

    彈簧被壓縮時，意味著彈簧要努力伸張，從而努力保持氣門的落座狀態。
  7. During the process of measuring valve phase, the grating displacement sensor and photoelectric axis - angle encoder are applied to measure the displacement of valve and the angle of curving shaft respectively. their signals are sampled and imported into computer. then the three signals are compared to find the relationship of valve phases in order to offer the reliable measuring parameters for the researchers and quality controllers

    在氣門相位測量中，採用光柵位移傳感器和光電軸角編碼器，分別將發動機進、排氣門位移量和曲軸旋轉位移量的變化信號通過采樣，輸入計算機，對三路信號加以比較找出氣門的相位關系，從而為設計開發人員、品質控制人員提供可靠的測量參數。
  8. The structure and characteristic of electronic throttle is introduced and a fuzzy neural network control algorithm based on gauss function is presented

    本文介紹了電子節氣門的結構和特點，提出了基於模糊高斯函數神經網路的電子節氣門控制方法。
  9. Precise control of electronic throttle is critical to drive ability, fuel economy and emission performance of hybrid electrical vehicle

    摘要電子節氣門的精確控制對于混合電動車的驅動性能、燃油經濟性能和排放性能是尤其重要的。
  10. In this paper, the general theory and numerical solution procedure were described. by building a diesel modeling with vertical valves and a piston bowl, a whole cycle was calculated, which include intake stroke, compression stroke, expansion stroke and exhaust stroke

    通過對帶有進、排氣門的柴油機進行計算，模擬了一個完整循環內進氣道、氣門和缸內氣體流動的全過程。
  11. Ruian nanfang valve factory, set up in 1995, emerged with sanhuan group of hubei air valve plane is a joint stock cooperation enterprise. it adopts the kernel technology and many years production experiences from hubei air plant. its workmanship and quality are in the leading position in the same field at home

    瑞安市南方氣門廠屬股份合作制民營企業，始建於一九九五年，后與三環集團湖北氣門廠聯合，吸取了湖北氣門廠的技術精髓和多年生產氣門的生產技術工藝流程經驗，生產工藝產品質量名列國內同類產品前茅。
  12. Zhejiang shang yu dong xin automobile parts manufacture co., ltd ( former zhejiang yu huan san you engine valve factory co., ltd ) is a professional manufacturing factory which produces automobile valves

    浙江省上虞市東鑫汽車配件製造有限公司（原浙江玉環三友氣門廠） ，是生產汽車氣門的專業製造廠，公司擁有一支高素質員工隊伍，有著多年從事汽車氣門開發、生產、服務的豐富經驗。
  13. To coordinate the four - stroke cycle, a group of parts called the valve train opens and closes the valves ( moves them down and up, respectively )

    那些打開和關閉氣門的氣門傳動是為了協調四沖程的工作循環（使他們各自上下移動） 。
  14. Automatic mechanical transmission as so called amt, accomplishes automatic gearshift based on manual fixed - shaft and dry clutch, which takes ecu as kernel, and then uses hydraulic system to control clutch, gearshift and manipulates throttle by adopting electronics technique and automatic gearshift theory

    電控機械式自動變速器（ amt ）是在傳統固定軸式變速器和乾式離合器的基礎上，採用電子技術和自動變速理論，以電子控制單元為核心，通過液壓執行系統控制離合器的分離與接合，選換檔操作以及發動機節氣門的調節來實現起步、換檔的自動操縱。
  15. The air inlet noise is one of the major aerodynamic noises of the diesel generator as a result of the pressure fluctuation caused by the periodic opening and closing of the inlet valve

    進氣噪聲是柴油機的主要空氣動力噪聲之一，它是由進氣門的周期性開啟與閉合而產生的壓力起伏變化而形成的。
  16. Recheck clearance on all valves again after locknut is tightened

    防松螺母擰緊后，再對所有氣門的間隙重新檢查一次。
  17. Fuel efficiency and power output and emission of an internal combustion engine can be significantly improved by optimizing intake and exhaust valve timing and duration and lift as speed changes during operation

    改變發動機氣門的開啟相位、持續時間和升程是改善發動機性能，提高熱效率和減少有害排放的一種重要方法。
  18. Considering the probability of the collision of the valve and the piston of the engine, to obtain the adjust ability of valve timing of the haecvvs in different speeds, the moving of the valve and the piston have been simulated. some strategies to avoid the collision have been put forward. the temperature of solenoid coil rose sharply both in low engine speed and in high engine speed

    根據發動機活塞的運動規律及電控可變氣門系統的啟、閉特性，對不同轉速下活塞與氣門的相對位置進行模擬，以保證氣門不與活塞發生碰撞為約束條件，對氣門正時調節能力隨轉速的變化規律進行了研究，在此基礎上討論了氣門與發動機活塞避免碰撞的方案。
  19. This device is an important part in valve driving mechanism, it works according to the movement rule of cam to ensure the exhaust port open and close correctly, so that it can make the diesel engine running normally

    該推桿裝置是氣門驅動機構中的重要部件，它按照凸輪的運動規律進行工作，來完成進排氣門的正確開啟和關閉，從而使柴油機正常運行。
  20. The valve seating velocity in the haecvvs was found to be lower under conditions of high and low speed of the diesel engine. and it was found that the haecvvs could work steadily

    對電控可變氣門系統中氣門的運動速度進行了研究，發現在高、低轉速時，電控可變氣門系統均具有氣門落座速度低的特點。
分享友人
分享到 Line

分享到臉書