氣體計量器 的英文怎麼說

中文拼音 [qìtǐjìliángqì]
氣體計量器 英文
gasometer
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 體 : 體構詞成分。
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 氣體 : gas; gaseous fluid
  • 計量 : calculate; estimate; meterage; metering; batching; measure
  1. This paper deriving the theory work inflection point in the static stage characteristics curve of small measurement range linear dimension measurement. by the way of high pressure and back pressure pneumatic measure and designed the parameter of the mainly and measure spray head, which are the key component in the spray head - baffle pneumatic sensor. the different groups for the main - spray head and the measure spray head, will effect the dynamic and static stage characteristic parameter. the author have done contrast experiment and optimization design to test and verify the theory derivation whereby made the rang of show valve of pneumatic measure system measure range up to 40 u m, the sensitivity up to 100mv / u m, resolution up to 0. 05 p m, the uncertainly of measure is less than 0. o2 u m, satisfaction of requirement of groups the carboy hatch thickness size precise measure of soft shims

    對高壓背壓式氣動測量用於小量程線性尺寸測量的靜態特性曲線的理論工作拐點進行了推導，對氣動測量系統中的噴嘴-擋板型氣動傳感器中的關鍵部件? ?主噴嘴和測量噴嘴的參數進行了理論設計，對主噴嘴和測量噴嘴的不同組合，將影響測量系統靜、動態特性指標的噴嘴參數進行了對比實驗和優化設計，並通過實驗驗證了理論推導，從而使氣動測量系統量程的示值范圍達到40 m ，靈敏度達到100mv m ，解析度達到0 . 05 m ，測量不確定度小於0 . 2 m ，滿足了壓縮機缸蓋軟體墊片厚度尺寸精密測量分組的要求。
  2. The key components in laser gyro is he - ne ring laser, and the reciprocal action theory between light and medium is the base in studying the ring laser, use the lamb half classical theory, and on the base of density matrix theory, the optical brounch equation was established, which described the movement of amplifying medium atom in the ring syntonic cavity, and according to the medium polarize theory the self consistent equations was deduced, which describe the light intensity and phasic of the counter - propagating wave. on the basis of this equations, adopted the simulation software matlab and virtual instrument programming language labwindows / cvi, we can do some simulated experiments in study the phenomenas such as amplify and dispersive characteristic of medium, mode pushing effection, burned hole effection and pattern competition, lock - in of frequency and the characteristic of light intensity and phasic of the counter - propagating wave in laser gyro

    激光陀螺的核心部件為he - ne環形激光器，而掌握光與介質的相互作用理論是研究激光器的關鍵，採用拉姆半經典理論為主，在密度矩陣理論的基礎上，推導環形諧振腔中描述he - ne氣體增益介質原子運動的光學布洛赫方程，運用介質極化理論得出描述激光陀螺反向行波的光強、位相所滿足的自洽場方程組，在此基礎上，運用matlab模擬軟體和虛擬儀器編程語言labwindows / cvi ，對激光陀螺中的介質增益色散特性、頻率牽引效應、燒孔效應及模競爭、閉鎖效應及環激光的光強和相位特性進行模擬試驗研究，並且運用全量子理論，對激光工作原理進行分析，得出二能級系統單模輻射場的光子數密度分佈，得出激光場的光子統計分佈，模擬激光場的動態建立過程。
  3. Utilising dissolved gases analysis, a new insulation fault diagnosis method for power transformers is proposed. this method is based on the group grey relational grade analysis method. first, according to the fault type and grey reference sequence structure, some typical fault samples are divided into several sets of grey reference sequences. these sets are structured as one grey reference sequence group. secondly, according to a new calculation method of the grey relational coefficient, the individual relational coefficient and grade are computed. then according to the given calculation method for the group grey relation grade, the group grey relational grade is computed and the group grey relational grade matrix is structured. finally, according to the relational sequence, the insulation fault is identified for power transformers. the results of a large quantity of instant analyses show that the proposed method has higher diagnosis accuracy and reliability than the three - ratio method and the traditional grey relational method. it has good classified diagnosis ability and reliability

    基於變壓器油中溶解氣體分析，提出了一種基於群灰色關聯度分析的變壓器絕緣故障診斷新方法.首先根據故障類型與灰色參考序列構造，選擇變壓器典型故障樣本構造多組參考序列，這些參考序列組構成一個灰色參考序列群.其次根據給出的新的關聯系數計算方法，計算個體關聯系數和關聯度.然後根據給出的群灰色關聯度計算方法，計算群灰色關聯度和構造群灰色關聯度矩陣.最後根據關聯序識別變壓器絕緣故障診斷.通過大量變壓器絕緣故障診斷實例分析，所提方法診斷準確性與可靠性優於三比值法和傳統的灰色關聯分析方法，具有較好的分類診斷能力和可靠性
  4. Aiming at such problems in combustion system of homemade middle and miniature boiler, as a complex system with the character of dead zone, time variation, serious non - linearity, large time delay, coupling and a lot of disturbance, this paper presents a new set of optimal control resources. by using well - matched control method on system, stable automatic running is realized. having the serious divulgence coals difference a lot from each other in character, instability of chemistry, value of lowest emission of heat, home - made boiler controller is not at all ideal. instead of traditional model that controls the ratio based on proportional control or with the correct signal of the amount of oxygen, this paper, combined with intellect control theory - - fuzzy control and self - optimizing concept, propounded a kind of fuzzy self - optimizing controller to be used in air supplying system of the boiler, and expatiates on the idea of dividing the control process into two parts, dynamic and static to realize, thus meets the demand of homemade boiler economic running

    本設計針對國產中、小型電站鍋爐燃燒系統參數時變、嚴重非線性、干擾因素復雜、耦合嚴重、模型不易確定的特點，提出多變量協調控制方案，解決了系統可控性差，難以實現穩定自動運行的問題；在此基礎上，改變以往以煙氣含氧量控制送風的傳統模式，針對國產電站鍋爐設備主體及一、二次送風迴路泄露嚴重，煤種混雜、成分不穩定、燃燒發熱值低、燃燒效率不高等問題，應用智能控制理論中的模糊控制技術，結合自尋最優控制的思想，設計了一種模糊自尋優控制器，應用在電站鍋爐送風控制系統上，並闡述了動靜態兩種實現途徑，通過在線優化風煤配比，實現最佳經濟燃燒，切實保障了鍋爐的經濟運行。
  5. The gas feed automation system, which includes field instruments, gas feed controller, wireless remote supervising system, and so on, will realize following functions : gas flow measurement, gas pressure and temperature measurement, gas flow control, gas pressure regulation, intermittent gas lift, wireless remote monitoring, and etc. this paper will discuss the following content in detail : first part is introduction

    該自控系統包括現場變送儀表、氣舉配氣控制器和無線遠程監控等，主要完成天然氣流量計量、氣體壓力溫度檢測、天然氣流量控制、管道干壓調節、間歇氣舉以及遠程監控等功能。本文將會重點介紹以下內容：首先是概述部分，簡要介紹了氣舉採油技術和氣舉配氣系統的地位和現存問題，並介紹了配氣自控系統的主要性能和優點。
  6. With the viewpoint of dynamic and distributed parameters and parameters qualitatively coupled, computing modules of evaporator, gascooler, internal exchanger are programmed. in addition throttling valve and compressor are programmed. following are the main points of this thesis

    本文從製冷系統模擬的角度，用動態分佈參數及參數間定量耦合的觀點考察了蒸發器、氣體冷卻器和回熱器，編制了各個部件相應的計算程序。
  7. In order to look for the key factors governing fluidization characteristics in the dense phase pulverized powder feeder, the effects of the different operating conditions and the geometrical variables on the mass ratio of powder and gas and the stable conveying time of the system were investigated in the self - developed special dense phase powder conveying test - bed

    摘要為了尋找影響濃相粉體給料器流化特性的關鍵因素，在自行設計的專用小型濃相粉體輸送試驗臺上，考察了不同操作參數和結構參數對輸送固氣質量比和穩定給粉時間的影響，總結了各因素對流化質量的影響規律。
  8. Experiments on the gas flow patterns in the flowmeter prove that the algorithm used in arm digital gas mass flowmeter is capable of significantly improving the sensitivity of the heat sensor, hence superior in terms of the measurement of gas mass flow

    並將此演算法應用於以arm處理器為核心的數字式氣體質量流量計中實驗證明，該方法能夠明顯改善熱式傳感器的動態響應速度，實現其快速補償。
  9. Our next - generation high - resolution spectrometer is a novel combination of optics and electronics that is ideal for applications such as characterizing lasers, measuring gas absorbance, and determining atomic emission lines

    我們下一代高解析度分光計，是一種新的光學和電子學器件的組合，對在激光特徵分析，測量氣體吸光率和確定原子散射線等領域的應用很理想。
  10. An instrument for measuring the force or volume of inspiration or expiration in the lungs

    呼吸氣量測定器；肺活量計用以測量肺部吸入或呼出空氣的力量或體積的一種儀器
  11. Verification scheme of gas flow measuring instruments

    氣體流量計量器具檢定系統
  12. The precise measurement of thermodynamic temperatures, for example with a gas thermometer, is very difficult. practical temperature scales were therefore introduced to make use of instruments such as platinum resistance thermometers which are much easier to use and give much higher precision measurements

    要準確測量熱力學溫度（如使用氣體溫度計來進行測量）是十分困難的，因此利用鉑電阻溫度計等作測量器的實用溫標便被採用，令使用更為容易及測量更為精確。
  13. Nozzle in the furnace the gas - quenching pressure can be 15 bar, airflow is big and uniform, cooling rate is very high

    配置內置高效熱交換器，以及經優化設計的氣淬系統，冷卻氣體流量均勻且流速大，冷卻速度高
  14. Based on advanced technology, this thesis bring forward the optimal scheme and set down general system - drawings and flow charts. using step7 - micro software, we achieve the auto - control aim in drinking water treatment. in practice, the complexity and non - linaerity exit in the system of water treatment, so we apply fuzzy control in water treatment and design a kind of controller which structure can be altered according to the using - rate of ozone and the variety of water quality

    實際飲用水處理系統由於存在復雜性、非線性、時變性，本文根據臭氧生物活性炭水處理工藝存在復雜性、非線性、時變性等特點，將模糊控制應用在水處理這一不確定的非線性時變系統，針對不同水溫下臭氧利用率及水質的變化，設計一種基於系統過程狀態的變結構的模糊控制器，以單片機作為主要控制硬體，按查表方式設計軟體，對進水閥門開度進行在線控制，調節臭氧氣體與進水的比例（臭氧流量及濃度不變） ，達到氣水比最優化。
  15. Considered the tiny quantity of the hydrogen, first we choose the gas chromatography technology to analyze the component of the work gas and to obtain the chromatography curve. then, treat the curve with the adaptive aperiodic stochastic resonance algorithm in order to eliminate the apparatus noise submerged in the tiny hydrogen signal. at last, calculate the quantity of the hydrogen based on that the quantity varies directly as a function of the area of the chromatography curve

    考慮到氫的含量非常微弱，在測量時採用氣相色譜法，並通過自適應非線性隨機共振演算法對色譜信號進行處理，以便提取出被儀器噪聲淹沒了的微弱氫信號的色譜曲線，最後根據氫含量與其色譜峰面積呈正比計算出工作氣體中的氫含量。
  16. As the key of the sample injection, a digital control instrument of mass flow controller ( mfc ), which can work in online and offline mode, was designed. it can give 4 flow signals accurately at the same time. the concentration and flux of the sample gas can be set by the instrument software

    進樣裝置的核心是自行設計開發的新型流量控制儀，該儀器採用數字介面，可以以聯機和脫機方式工作，能夠同時快速準確地輸出4路流量控制信號，對測試氣體的流量和濃度進行設定。
  17. The pressure switch is suitable for almost all liquid and gaseous mediums and is used in vacuum technology pump control, gas technology stock monitoring, leak detection, filter monitoring dirt detection, as well as a whole variety of measurement tasks in hydraulics and pneumatics, in machine, equipment and plant construction, in process technology and in building technology

    壓力開關幾乎適用於所有液體和氣體介質，可以用於真空技術氣泵控制氣體技術貯存量監測泄露探測過濾監測灰塵探測，也用於過程技術和建造技術的機器機械和設備製造中的所有液壓和氣壓測量任務。前置式設計使開關能用於高粘稠和結晶介質。
  18. It is an effective way to solve this problem by combining piezoelectric quartz crystal sensor array with chemometrics. however, there were few reports in designing electric circuit, which would influence the response due to mutually interfering between oscillators. so, it is necessary to design a vibration circuit and develop it into small and convenient instrumentation to overcome this limitation

    另一方面，單一的具有選擇性的傳感器在實際多組分氣體的檢測中受到限制，而採用壓電石英傳感器陣列再結合化學計量學手段進行數據處理卻是解決這個問題的一個有效途徑，然而在它的電路設計方面，由於共振電路間的相互影響，使檢測受到很大幹擾，因此設計一個相互無干擾的起振裝置來解決這個問題是十分有必要的。
  19. In experimentation, the project adopts computer, data collection board, sensor and software. finally, the theory analsis is validated that the contact of noise elimination, velocity of flow, resistance loss

    在試驗中，採用了以計算機、數據採集卡、傳感器和處理軟體得到阻性消聲器的動態特性，從而驗證了阻性消聲器的消聲量、氣體流速和阻力損失之間聯系的理論分析。
  20. In order to change the behindhand state in measurement of natural gas of liaohe oil field, we make the technique reformation, using the normal hole - board, intelligent sensor, natural gas compression factor, arithmetic of volume flux and compensatory technology

    為了改變遼河油田天然氣落後的計量狀態，我們採用標準孔板、智能傳感器、國際標準天然氣壓縮因子、體積流量演算法和補償技術進行天然氣計量技術改造。
分享友人
分享到 Line

分享到臉書