水壓噴嘴 的英文怎麼說

中文拼音 [shuǐyāpēnzuǐ]
水壓噴嘴 英文
hydraulic nozzle
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 壓 : 壓構詞成分。
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 水壓 : water gage; hydraulic pressure （用英寸高度表示的）水壓泵 hydraulic pump; 水壓鍛造 hydraulic forg...
  1. As to the work about theory analysis, at first, the paper describes the atomizing and humidifying process of the centrifugal nozzle with firing pin type, high pressure and little aperture and liquid physical properties. later, combining with the structure characters of this kind of nozzle, the paper studies on the theory of the atomizing and humidifying process by three phases, which is water film forming phase, water film falling into pieces phase, and heat and mass transfer between water and air phase in turn

    理論工作方面，首先描述了撞針型高壓小孔徑離心式噴嘴的霧化加濕過程和液體的物理性質，然後結合撞針型高壓小孔徑離心式噴嘴的結構特點，將其霧化加濕過程分三個階段進行機理上的研究，這三個階段依次為液膜形成、液膜初次破碎及二次霧化、水與空氣的熱濕交換。
  2. Based on the theory analysis and experiment work, the paper studies the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture. compared with the traditional air washer, the high efficiency and energy saving character of this kind of nozzle is stood out

    課題從理論和試驗兩方面分析研究了撞針型高壓小孔徑離心式噴嘴的霧化加濕性能，並將其與傳統噴水室加濕系統進行能耗比較，突出了撞針型高壓小孔徑離心式噴嘴高效節能的特點。
  3. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  4. Integrated the work on theory and experiment, the paper provides technical performance material at large about the automating and humidifying character of the centrifugal nozzle with firing pin type, high pressure and little aperture to the manufacture and user. with the valuable reference during the selecting the equipment and ascertaining the parameters, the users could select and control the humid parameter

    課題的理論與試驗兩方面工作相結合，為撞針型高壓小孔徑離心式噴嘴的霧化加濕性能提供了較為詳細的技術性能資料，為生產廠家和用戶在設備選型和參數選擇過程中，提供了有價值的參考，便於用戶正確而經濟地選擇、控制濕度參數，有效調節噴嘴孔徑、噴水初溫和噴水壓力的大小。
  5. With gelatin liquor as adhesive and wheat meal as granulation material, the effects on spray granule ' s strength of fluidizing gas velocity, bed temperature, nozzle air pressure and adhesive concentration were studied experimentally in a batch conical fluidized bed spray particle generator

    本文在一間歇錐形流化床噴霧造粒器中，以食用小麥澱粉為原料，以明膠的水溶液為粘結劑，實驗研究了流化氣速、床層溫度、噴嘴霧化空氣壓力、粘結劑濃度對噴霧造粒顆粒強度的影響。
  6. Low frequency micro - vibration causes the micro - fluid to produce uniform dispersion and injection which carried out a hydrophobization treatment on the inner wall of micro - nozzle, thus eliminated the spontaneous flowing of micro - fluid inside the micro - nozzle due to wet ting effect so as to let the micro - injection be provided with a digitalized and volume controllable character

    壓電陶瓷低頻微振動使得微流體產生均勻的離散和噴射；對微噴嘴內壁進行疏水化處理，從而消除微流體由於濕潤作用在微噴嘴內部的自發性流動，使得微噴射具有數字化量可控的特徵。
  7. Based on the induction phenomenon caused in gas hydrate formation, the influential rules of its gas entrance mode, temperature, pressure, water resources and nozzle on the induction time are analyzed by means of experimental study on the induction time of gas hydrate formation obtained by water spray and enhancement

    摘要以氣體水合物形成過程中的誘導現象為基礎，通過對噴霧強化方式制取天然氣水合物的誘導時間進行試驗研究，考察分析了系統進氣方式、溫度、壓力、水源及噴嘴等因素對誘導時間的影響規律。
  8. Studies the impact of nozzle aperture, initial temperature and pressure of spray water and initial air state on humidifying effects based on an orthogonal test

    摘要通過正交試驗確定了噴嘴孔徑、噴水初溫、噴水壓力及空氣初狀態對加濕效果影響的顯著程度。
  9. Quantitatively analyses the concrete influences on atomizing humidifying performance of the nozzle aperture, initial temperature and the pressure of spray water and the water - air ratio through a single factor experiment

    通過單因素試驗定量分析了噴嘴孔徑、噴水初溫、噴水壓力以及水氣比對霧化加濕的具體影響。
  10. Gas - fired central heating boilers - specific requirements for the domestic hot water operation of combination boilers of nominal heat input not exceeding 70 kw

    裝有常壓送風噴嘴的燃氣集中供暖鍋爐.公稱熱輸入量不超過70kw的混合鍋爐的家庭熱水供暖的具體要求
  11. Its atomized parcel is so small that no drip is separated out. this kind of centrifugal nozzle has high humidifying efficiency and low energy cost, which could be used in many situations in textile factories such as directly humidifying in workshop and humidifying in air pipeline

    撞針型高壓小孔徑離心式噴嘴的霧化粒子細小、無水滴析出、加濕效率高、耗能少，可直接向車間加濕，適用於紡織廠等多種應用場合。
  12. As to the work about experiment study, at first, the paper makes certain the prominent affecting factors to the automating and humidifying property of this kind of nozzle by orthogonal experiment. by jicha analysis method and fangcha analysis method, the paper got that the nozzle aperture, the initial water temperature and the spraying pressure have prominent effect to the humidifying property while the effect of the original air state is small

    試驗工作方面，首先通過正交試驗確定對撞針型高壓小孔徑離心式噴嘴霧化加濕性能影響顯著的因素，運用極差分析法和方差分析法，得到噴嘴孔徑、噴水初溫和噴水壓力對噴嘴的加濕性能影響顯著，而待加濕空氣初狀態的影響相對較小。
  13. Later, the paper ascertains how the prominent factors influence the humidifying effect by single factor experiment and got such solutions : when other situations do n ' t change, the nozzle flux will enhance with the increase of the nozzle aperture and spraying pressure. air ' s changing quantity of enthalpy and absolute humid, valid humidified quantity, humidifying efficiency and saturation efficiency will enhance with the increase of the initial water temperature. with the enhance of the praying pressure, the valid humidified quantity and air ' s changing quantity of enthalpy will increase first and decrease later, while the humidifying efficiency will drop

    然後通過單因素試驗確定影響顯著的因素如何作用加濕效果，得到：在其他條件不變的情況下，噴嘴流量隨噴嘴孔徑和噴水壓力的升高而增大，空氣焓變量、絕對濕度差、有效加濕量、加濕效率及飽和效率隨噴水初溫的升高而提高，有效加濕量和空氣焓變量隨噴水壓力的升高先增加然後有所下降，而加濕效率隨噴水壓力的升高而下降，焓變量和絕對濕度差隨水氣比的增加而增大。
  14. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
  15. Experiment shows that when the gas hydrate is obtained by spray, its induction time is generally shorter, its phenomenon is not obvious, setting of initial temperature and pressure with an autoclave has certain influence on induction time, but not obvious, water resources and spray nozzle have bigger influence on the induction time

    試驗表明，噴霧方式制取天然氣水合物時，誘導時間普遍較短，誘導現象不明顯；反應釜設定初始溫度和壓力對誘導時間有一定影響，但不是很明顯；水源和霧化噴嘴對誘導時間的影響較大。
  16. Water injection system includes pulverization system and controlling system of water quantity. pulverization system includes air resource, water resource and gas - mist nozzle ; controlling system of water quantity includes booster, controlling circuits. water quantity is decided by hydraulic pressure and gas pressure

    噴水系統包括霧化系統及水量控制系統，其中霧化系統包括空氣源（空氣壓縮機） 、水源（加壓水）及氣?霧噴嘴；水量控制系統包括比例調壓閥、控制電路部分。
  17. Mecc dayin has abundant experiences and advantages in designing hp nozzle seal and water supplying system. mecc dayin will supply high quality products and perfect service for you

    作為國內一流的專業生產液壓系統、液壓元件的邁克液壓公司的一個分廠，我們在高壓噴嘴的密封及整體配水系統的設計製作安裝調試方面都有更為整體化，全局化的設計經驗和優勢。
  18. 3. testing all the hydraulic parameters of the sprinkler installed with adjuster such as working pressure, water flux, the range of the sprinkler, intensity of water drop impact, characteristic of water distribution, etc. according to the testing data, we can learn the quantitative relations among the structure of the adjuster, working pressure, diameter of the nozzle, elevation of sprinkler, wind power, velocity of rotation and the range of water

    測試安裝「壓力調節器」后的噴頭的水力性能參數，即工作壓力、流量、射程、水滴的打擊強度、噴灑水分佈特性等。依據所測得的噴頭水力性能參數和射程數據，我們可較清楚的了解「壓力調節器」的結構形式、工作壓力、噴嘴直徑、噴射仰角、風力、旋轉速度和噴頭射程之間的定量關系。
  19. Grade with corrosion resistant binder ( waste water etc. ) sliding rings, sealing rings in construction of pumps, water meter pins, plungers, spraying nozzles, guiding and bearing parts, wearing parts in laboratory and milling and mixing plants, plugging parts gfk cable, etc

    耐腐蝕性的牌號，用於割捆機、滑動環、建築水泵中的密封環、水位計的銷釘、活塞、噴嘴、承壓零件、實驗室中的耐磨零件和銑削混合設備。
  20. Full size orifice - all series n388 valves have a full - size orifice to assure pipe size capacity. water passages are streamline to provide high water flow with minimal pressure loss

    全通徑噴嘴-所有系列n388閥門都有一個全通徑噴嘴以確保管道口徑的通過能力。水流道為流線型，在壓降最小前提下實現高流量。
分享友人
分享到 Line

分享到臉書