水果切割 的英文怎麼說
中文拼音 [shuǐguǒqiēgē]
水果切割
英文
fruit cutting-
It still works well when the mulched straw is more then lot / ha. ( 3 ) an experiment was conducted on a self - made testing equipment to investigate the chopping properties of wheat straw under different conditions. on the basis of testing results, main cutting curves of wheat straw were given under different cutting speeds of rotary blade, with different straw lengths, different moisture contents, different cutting position, different thick of knife edge, with and without shear bar
（ 3 ）為了研究帶狀粉碎防堵裝置對麥秸的切碎效果，在特製的實驗臺上，應用了虛擬儀器測試技術對不同處理的麥稈進行了切斷試驗，得到了在不同切割速度下對不同長度、不同含水率的麥稈、麥稈的不同切割部位以及有定刀和無定刀情況下的切斷率，為麥秸粉碎裝置的設計提供了依據。The results of large - scaled culture show that 48g clone crushed by tissue disintegrator in the course of initial period and its inoculating density is 0. 35g / l, a month later, the clone departed directly and its density is 1. 5g / l, the highest density of each jar could be obtained 410g, the growth speed mostly doubled per week
大規模培養結果表明在20l廣口瓶中（有效水體15l ） ， 48g克隆在起始培養時經組織搗碎機粉碎切割，切割時間10s （細胞段長度約200um ） ，並按0 . 35g l接種，一個月後不粉碎直接分瓶，分瓶密度1 . 5g l ，一個月後最大密度410g瓶，生長速度約每周翻一番。Suitable for precision instruments maintenance and cleaning, such as lcd, notebook, wafer, semiconductor products
我們生產的無塵擦拭布具超強除塵效果、高吸水率、柔軟不損傷表面，完全采鐳射切割。It is widely applicable to lotus paste filling with equal density, applied in cutting and rationing the fruit filling
適用於各類密度均勻的蓉餡料、水果餡料的切割定量。Some problems of the turbomachinery runner are introduced in the paper, which includes the hydraulic computation and analysis of the turbomachinery runner, the optimum selection and practical application of the reconstruct scheme, and test verification of increasing capability after the reconstructing
主要介紹了豐滿電廠水輪機轉輪出水邊切割增容的水力計算和分析、方案的優選及實施、增容效果的試驗驗證。Based on the quality of incision, the paper puts forward the plan of how to choose the craft parameters and quality parameters of pre - mixed abrasive water - jet, how to work on the experiment of the incision quality and how to analyse the result of the experimentation
摘要以切割質量研究為切入點，提出了前混合磨料水射流切割質量實驗設計中工藝參數的選取與質量參數的選定、切割質量實驗方案實施以及實驗結果分析的方案。[ 3 ] the greatest error is 50 % between the result given by the affinity law of u. s. a and that calculated by using the trim law issued in this work
（ 3 ）發現在輸送水時美國的葉輪切割定律計算結果與本文相差最大為50 。按美國的切割指數用於離心油泵葉輪切割，誤差比較大。Based on the findings of the investigation, the following conclusions should be made : [ 1 ] the affinity law of impeller trim for the centrifugal oil pump 65y60 is obtained when handling water from the experiments
通過研究，取得到了以下研究成果： （ 1 ）得到了輸送水時65y60型離心油泵葉輪切割定律。分享友人