水錐理論 的英文怎麼說

中文拼音 [shuǐzhuīlún]
水錐理論 英文
water coning theory
  • : 名詞1 (由兩個氫原子和一個氧原子結合而成的液體) water 2 (河流) river 3 (指江、河、湖、海、洋...
  • : Ⅰ名詞1. (錐子) awl2. (似錐物) awl-shaped things 3. (錐體) cone Ⅱ動詞(鉆) drill; bore
  • : Ⅰ名詞1 (物質組織的條紋) texture; grain (in wood skin etc ) 2 (道理;事理) reason; logic; tru...
  • : 論名詞(記錄孔子及其門徒的言行的「論語」) the analects of confucius
  • 理論 : theory
  1. By use of this theoretical solution, the stress for various dryers with different pyramidal neck dimension is solved to study the influencing of dimension change on the stress level, from that the design request of the dimension of this transitional structure is put forward

    通過運用本解法對各規格烘缸不同頸過渡尺寸的應力求解,研究頸過渡尺寸對該結構段應力平的影響情況,並由此提出過渡結構尺寸設計的要點。
  2. The theoretical study of the recovery percent vs. water cut of thin and bottom water reservoir in luliang oilfield is based on developing its geologic and flow models, obtaining oil - thickness ratio, oil - water viscosity ratio, relative permeability curve parameter and chart of effect of bottom water toning, etc., on water - yielding pattern of the reservoir

    摘要在建立了陸梁薄層底藏地質及滲流模型基礎上,採用研究的方法,研究了薄層底油藏采出程度與含率關系式,並獲得了油厚比、油粘度比、相滲曲線特徵參數以及底進等對油藏產規律的影響關系圖版。
  3. The conclusions are as follows : ( 1 ) high - pressure water - atomization can be used to produce a pre - alloyed steel powder with high apparent density, high green strength, size - stability after sintering and low hydrogen - loss content ; ( 2 ) the higher smelting temperature and / or water pressure, the finer particle size of steel powders ; ( 3 ) when the atomization angle holds in a reasonable value ' s range the obtained powder will have a better particle size distribution ; ( 4 ) an optimum atomization technological parameters : liquid steel flux, water pressure and water prick angle was obtained ( 5 ) reduction variables ( temperature, holding time, material - bed ' s thickness and reducing gas flux ) have a significant effect on the particle agglomeration and properties of final powder was given ( 6 ) different alloying methods were developed to modify properties of ferrous powder materials and hence to broaden its applications in ferrous powder metallurgy industry

    本文系統研究了霧化預合金鋼粉生產工藝及合金化方法對鐵基粉末冶金材料性能影響,詳細研究了冶煉、霧化、還原工藝參數對預合金鋼粉化學成份和物性能影響,並得出如下結: ( 1 )採用高壓霧化技術可用於生產高密度、高強度、尺寸穩定性的低氫損含量的霧化預合金鋼粉。 ( 2 )冶煉溫度越高,高壓壓力越大,所得生粉顆粒粒度越細。 ( 3 )角調整在一個適當角度范圍內可獲得粒度組成較好的生粉。
分享友人