油泵組件 的英文怎麼說
中文拼音 [yóubèngzǔjiàn]
油泵組件
英文
assembly number oil pump-
Specification for subsurface sucker rod pumps and fittings
抽油泵及其組件規范This system includes fuel oil tank, fuel oil pump, fuel oil hand pump, auxiliary engine daily service tank, piping and valves
本系統由燃油艙、燃油駁運泵、燃油手搖泵、輔機日用油櫃、管路及閥件等組成The second chapter simply introduces the development of alternate asynchronous inverter technology and retrospects some types of energy - saving systems for hydraulic elevators. then the working principles of the project are discussed and analyzed at four different working status, i. e. light load upwards, heavy load upwards, light load downwards and heavy load downwards. and the chapter focus on the introduction of structure design of pump station, calculation and type selection of pump / motor reversible units, research on oil leakage principles of accumulator circuit, design of accumulator - pump / motor pressure - energy transformer and integrated valve blocks, etc. the last but not the least, the electrical wiring of vector inverter control cabin and design of computer control and data acquisition system are introduced
論文第二章首先簡單介紹了交流異步電動機變頻調速技術的發展概況，在回顧電梯液壓控制系統節能技術的基礎上，介紹了本課題研製的「採用蓄能器的液壓電梯變頻節能控制系統研究」的基本原理，分析了動力系統在電梯轎廂輕載上下行、重載上下行等四種典型工況下的基本工作狀態和工作方式；詳細地介紹了本課題節能系統液壓動力泵站的結構設計和參數設計，重點研究了液壓動力泵站的結構設計、液壓泵馬達可逆性問題及其選型設計計算、蓄能器迴路泄漏油損失機理的研究及其補償裝置的設計、蓄能器-泵馬達壓力能量轉換裝置的設計、多功能集成控制閥組的設計等內容；最後簡單介紹了本課題矢量控制變頻控制櫃的外部附件電氣接線、計算機控制及數據採集系統的硬體設計等內容。High pressure pipe assemblies for diesel fuel injection pump test bench
柴油機噴油泵試驗臺用高壓油管組件Electrical submersible pump - technical specifications
潛油電泵機組技術條件Diesel engines - high - pressure fuel injection pipe assemblies - general requirements and dimensions
柴油發動機.高壓燃料噴射泵組件.一般要求和尺寸Failure analysis and technical improvement of distributing valve assembly of a main fuel pump
某主燃油泵分油活門組件失效分析及工藝改進There is a high precision anti - interference leakage detection sensor fitted in the enclosed oil chamber, and a thermosensitive element fitted in stator winding to carry out automatic protection of pump motor
該泵密封油室內設置有高精度抗干擾漏水檢測傳感器，定子繞組內預埋了熱敏元件，對水泵電機自動保護。In this paper, the load status for different shafts is analyzed after introducing their structures, and the several dynamic models are established under analyzing the status of load. the strength of the shafts is calculated with three - dimensional finite element method by ansys software. the mesh generation is automatic, and we use the method to generate 10 - node or 20 - node elements
本文在分析潛油電泵機組具體結構特點的基礎上，對不同類型的軸類零件做了受力分析，根據分析需要建立了不同的力學模型，並應用三維等參數單元法對軸類零件進行了強度分析和計算。分享友人