法蘭密封 的英文怎麼說

中文拼音 [fǎlánmìfēng]
法蘭密封 英文
flange seal
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 蘭 : 1 [植物學] （蘭花） orchid2 [植物學] （蘭草） fragrant thoroughwort3 [植物學] （古書上指木蘭） li...
  • 密 : Ⅰ名詞1 （秘密） secret 2 [紡織] （密度） density 3 （姓氏） a surname Ⅱ形容詞1 （距離近; 空隙小）...
  • 法蘭 : [機械工程] flange
  1. Engine flywheel housings with sealed flanges

    密封法蘭發動機飛輪殼
  2. Full face gaskets for flanges ; nominal pressures 6, 10, 16, 25

    法蘭用全密封面墊片.公稱壓力為6 10 16 25
  3. Basis for calculation of aluminium alloy pipe flanges with full face gasket

    具有全密封墊鋁合金管法蘭的計算基準
  4. Press the flange and replace the side sealing ring

    壓緊法蘭（均勻用力）更換側密封圈。
  5. 2 flange can base of custmers request to according state criterion of hg gb jb ansi jis bs din to smithing also can confirm by pact, because of machining craft of airproof - side, so advice to choose flat weld flange of board form neck form. airproof - sides are all planar airproof form, in order to install pipeline, we can afford volitant flange of flat welding

    2法蘭可根據用戶需要按hg gb jb ansi jis bs din等國家標準，可以是鍛造，也可由合同確定，因密封面加工工藝建議選用板式平焊法蘭帶頸平焊法蘭。
  6. It can be installed in horizontal or vertical. sealing gasket must be put on the connected, then equably tight the bolt

    本閥可水平安裝或垂直安裝，安裝時兩法蘭連接中間必須加密封墊片，然後鎖緊螺栓。
  7. Note : this table for the convention flange connection worm gear and worm drive metal hard seal fixed ball valve model establishment, the major parts material and the suitable operating mode, other requests and its model establishment sees the ball valve model establishment method

    注：本表為常規法蘭連接蝸輪蝸桿傳動金屬硬密封固定球閥的型號編制、主要零件材料及適用工況，其他要求及其型號編制見球閥型號編制方法。
  8. Connectors, electrical, circular, coupled by threaded ring, fire - resistant or non fire - resistant, operating temperatures 175 c continuous, 200 c continuous, 260 c peak - hermetic receptacle with round flange attached by soldering or brazing - product standard

    連續工作溫度為175 200極端溫度為260時耐火或不耐火的由螺紋環連接的環形電連接器.軟焊或銅焊上圓頭法蘭密封插座.產品標準
  9. Straight pattern valves with flange socket placed in shunt - part 1 : without lining

    分流器法蘭密封管座的直排型閥門.第1部分:無襯
  10. Straight pattern valves with flange socket in main power connection - part 3 : with rubber lining

    主電源連接裝置帶法蘭密封的流量觀察孔玻璃閥門.第3
  11. Different vacuum sealing and microwave transport

    微波傳輸系統真空法蘭密封結構設計特點
  12. Pipe flanges for ordinary use - sealing surfaces - forms and dimensions

    一般用途管法蘭密封面形狀和尺寸
  13. Jgd - f rubber flange pressurized pad

    Jgd - f型橡膠法蘭密封墊
  14. Jgd - f rubber flange gland bush

    Jgd - f型橡膠法蘭密封墊
  15. Flange sealing surface

    法蘭密封面
  16. Straight pattern valves with flange socket placed in shunt - part 2 : with enamel lining

    分流器中帶法蘭密封的流量觀查孔玻璃閥門.第1部分:琺
  17. Straight pattern valves with flange socket in main power connection - part 1 : without lining

    主電源連接的法蘭密封管座直排型閥門.第1部分:無襯
  18. Straight pattern valves with flange socket in main power connection - part 2 : with plastic lining

    主電源連接的法蘭密封管座直排型閥門.第2部分:帶塑料
  19. Design of processing device for the spot recovery of flange sealing - face on large - sized pressure vessels

    大型壓力容器法蘭密封面現場修復加工裝置的設計
  20. Flanges for tank trucks ; gaskets

    油罐車的安裝法蘭.密封墊
分享友人
分享到 Line

分享到臉書