波紋管膨脹節 的英文怎麼說

中文拼音 [bōwénguǎnpéngzhàngjié]
波紋管膨脹節 英文
expansinon bellows
  • 波 : Ⅰ名詞1 （波浪） wave 2 [物理學] （振動傳播的過程） wave 3 （意外變化） an unexpected turn of even...
  • 紋 : 名詞（花紋; 紋縷兒） lines; veins; grain
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  • 膨 : 動詞（物體的長度或體積增加） expand; swell
  • 脹 : 動詞1. （膨脹） expand; dilate; inflate 2. （脹大） swell; distend; bloat
  • 節 : 節構詞成分。
  • 波紋 : corrugation; flow mark; moire; cockles; dimple; washmarking; [電工] ripple
  • 膨脹 : expand; swell; dilate; inflate; puff; bulge; inflation; expansion; dilatation; buckling; swelling...
  1. Pipework - metal bellows expansion joints - general

    管道工程.金屬波紋管膨脹節.總則
  2. General specification for metal bellows expansion joints

    金屬波紋管膨脹節通用技術條件
  3. Code of practice for the selection and application of bellows expansion joints for use in pressure systems - metallic bellows expansion joints

    壓力系統用波紋管膨脹節選用慣例.第1部分:金屬波紋管膨脹節
  4. The software takes visual basic6. 0 as work flat, adopting activex technique, transfers autocad2000 painting orders from the exterior of vb through programme method. it is a re - exploitation software to design bellows expansion joints. the software adopts ejma, the current international widespread trade standard, as mathematics model

    波紋膨脹節是安裝在金屬管線上起熱補償、柔性連接等作用的管道連接構件，本文以visualbasic6 . 0作為操作平臺，採用activex技術，通過編程手段從vb外部調用autocad2000軟體中的繪圖命令，二次開發軟體，以目前國際上行業中普遍採用的ejma標準作為數學模型，編輯波紋膨脹節設計軟體。
  5. The teflon compensator, may call the corrugated pipe, also called theinflation festival, it may use for to eliminate the pipeline, thevessel either the equipment and so on the expansion and contractionwhich causes because of the climatic change or because otheroriginally thus cause heat expansion or displacement ; as one kind ofslow shaker

    聚四氟乙烯補償器，可稱波紋管，又稱膨脹節，它可用來消除管道、容器或設備等因氣候變化而引起的伸縮或因其他原因而導致的熱膨脹或位移；作為一種緩振器。
  6. Then experiment was processed to testify the calculated results. based on the theory of vibration mode, harmonic response and experiment, fea meshing, fea element and bound condition of expansion joint were analyzed. then a parametric fea modeling & post process software was developed by apdl and visual basic langrage

    本文採用有限元數值分析方法，利用大型商用有限元計算軟體ansys ，研究了基於結構參數化設計思想的波紋管膨脹節的振動模態和含波紋管膨脹節管系的振動響應分析方法，開展了波紋管膨脹節模態試驗驗證。
  7. Corrosion and protection of expansion joints in practical use

    波紋管膨脹節實際應用中的腐蝕分析與防護對策
  8. The software can realize diagram paper design of over ten thousand kinds of specification of u - type expansion joints and the design range is dn25 - 1000mm, low pressure and middle pressure, with compensating value smaller than the 300mm

    整個軟體可完成u型、加強u型和型各種規格波紋管的設計；通徑25 - 1000mm 、中低壓下、補償量小於300mm的u型膨脹節上萬種產品的圖紙設計。
  9. Research methods of expansion joint ' s mode and harmonic response were systemically studied and a fea modeling & post process software for project designer was built in this article. and it may contribute much to theory and project practice for expansion joint

    本文工作不僅較系統地完成了波紋管膨脹節振動模態與響應分析方法的研究，還為工程設計人員提供了基於參數化的有限元建模及后處理軟體，具有一定的理論意義和重要的工程應用價值。
  10. Expansion joint was one of the most important parts of pipe system. it can close the vibration off in pipe system and absorb the displacement caused by stress, axial force, transverse force and temperature grads. based on fea parametric analysis, ansys was used to study the mode and harmonic response of expansion joint in this article

    波紋管膨脹節是管系中的重要組成部件，它不僅能夠吸收由壓力、軸向力、橫向力、彎矩以及溫差等原因引起的位移，還可作為隔振元件用於管系的減振隔振。
  11. Meanwhile we discuss the multilayer bellows with boundary non - linearity theory, exercise fea software ansys construct a kind of novelty and logical model of multilayer bellows, then basically settle multilayer bellows of design and calculate. the results of ansys and the datum of experiments are accordant

    同時著重探討了多層波紋膨脹節，結合邊界非線性理論，運用有限元軟體ansys構造了一種新穎、合理的多層波紋管有限元模型，基本解決了多層波紋管設計計算問題。
分享友人
分享到 Line

分享到臉書